100NXXCAF

Model 100XXCAF Flangeless Attenuator 100 Watts General Specifications: Resistive Element: Thick film Substrate: Aluminum Nitride ceramic Electrical Specifications: Attenuation Range: 1, 2, 3, 4, 5, 6, 9, 10, 20 or 30 dB Frequency Range: DC – See Chart • DC – 3.0 GHz Power: 100 Watts • 100 Watts VSWR: 1.25:1 Features • AlN Ceramic • Non-Nichrome Resistive Element • Low VSWR Note: Tolerance is ±0.010”, unless otherwise specified. Designed to meet of exceed applicable portions of MIL-E-5400. Operating temperature is -55ºC to 155ºC (see chart for derating temperatures). Specifications subject to change with out notice. • 100% Tested Outline Drawing: USA / Canada: Toll Free: Europe: Available on Tape and Reel for Pick and Place Manufacturing Sheet 1 of 2 (315)432-8909 (800) 544-2414 +44 2392-232392 100NXXCAF (097) rev A.xlsx 100XXCAF Model Performance Specifications: Part Number Attenuation Value (A-B) Value (A-C) Value (B-C) Tol. Frequency Thickness "T" 100N1CAF 1dB+0.25/-0.6dB 4.8Ω 435Ω 435Ω ±4% DC - 2.2GHz 0.060 100N2CAF 2dB±0.40dB 9.6Ω 232Ω 232Ω ±4% DC - 2.2GHz 0.060 100N3CAF 3dB±0.40dB 15.2Ω 155Ω 155Ω ±4% DC - 2.5GHz 0.060 100N4CAF 4dB±0.40dB 22.0Ω 131Ω 131Ω ±4% DC - 2.5GHz 0.060 100N5CAF 5dB±0.40dB 28.5Ω 94.7Ω 94.7Ω ±4% DC - 3.0GHz 0.060 100N6CAF 6dB±0.40dB 33.7Ω 82.5Ω 82.5Ω ±4% DC - 3.0GHz 0.060 100N9CAF 9dB±1.0dB 50.6Ω 61.3Ω 61.3Ω ±4% DC - 2.2GHz 0.060 100N10CAF 10dB+1.5/-1.75dB 56.0Ω 60.0Ω 60.0Ω ±4% DC - 2.2GHz 0.060 100N20CAF 20dB±0.50dB 248Ω 61.0Ω 61.0Ω ±4% DC - 2.2GHz 0.040 100N30CAF 30dB±1.00dB 790Ω 53.0Ω 53.0Ω ±4% DC - 2.2GHz 0.040 Power De-rating: Mounting Footprint and Procedure: .025 MIN. (2 PLACES) BOARD LOWER THAN LEAD. BOARD EVEN WITH LEAD. BOARD LOWER THAN LEAD. BOARD HIGHER THAN LEAD. SUGGESTED STRESS RELIEF METHODS NOT RECOMMENDED APPLICATION SCALE: NONE SCALE: NONE 1. Make sure that the devices are mounted on flat surfaces (.001" under the device) to optimize the heat transfer. 2. Drill & Tap the heatsink for the appropriate thread size to be used. 3. Coat heatsink with a minimum amount of high quality silicone grease (.001" Max. thickness). 4. Position device on mounting surface & secure using socket head screws, flat & split washer, torque screws t the appropriate value. Make sure that the device is flat against the heatsink, (care should be taken to avoid upward pressure of the leads towards the lid). 5. Solder leads in place using an appropriate type solder with a controlled temperature iron (700°F). **For more details contact factory** USA / Canada: Toll Free: Europe: Available on Tape and Reel for Pick and Place Manufacturing Sheet 2 of 2 (315)432-8909 (800) 544-2414 +44 2392-232392 100NXXCAF (097) rev A.xlsx