B0322J5050AHF

Model B0322J5050AHF Rev F PRELIMINARY Ultra Low Profile 0805 Balun 50Ω to 50Ω Balanced Description The B0322J5050AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation wireless chipsets in an easy to use surface mount package covering the GSM frequency. The B0322J5050AHF is ideal for high volume manufacturing and is higher performance than traditional ceramic and lumped element baluns. The B0322J5050AHF has an unbalanced port impedance of 50 and a 50 balanced port impedance. This transformation enables single ended signals to be applied to differential ports on modern semiconductors. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0322J5050AHF is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25C) Features: Parameter Min. Frequency  300 – 2200 MHz  0.7mm Height Profile Unbalanced Port Impedance  50 Ohm to 2 x 25 Ohm Balanced Port Impedance  Low Insertion Loss Return Loss  Surface Mountable Insertion Loss*  Tape & Reel Amplitude Balance  Non-conductive Phase Balance Surface  RoHS Compliant CMRR  Halogen Free Power Handling @85C Power Handling @105C Operating Temperature Typ. Max 300 12.2 2200 50 50 16 1.3 1.1 17 15 Min. 700 12.2 1.6 1.3 21 2 1.2 +105 -55 Typ. Max 2000 50 50 16 1.1 0.4 7 24 1.5 0.7 9 2 1.2 +105 -55 Unit MHz Ω Ω dB dB dB Degrees dB Watts Watts ºC * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing TOP VIEW (Near Side) SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 2.04±0.10 0.71±0.07 1 3 2 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 5 4 4x 0.65 6x 0.30 Designation Unbalanced Port GND Balanced Port Balanced Port Do not connect NC Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0322J5050AHF Rev F Typical Performance: 200 MHz to 2300 MHz Differential insertion loss 0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] [dB] Return Loss 0 -18 -2.1 -24 -2.4 -27 -2.7 -30 -3 -33 -3.3 -36 0.2 0.5 0.8 1.1 1.4 Freq [GHz] 1.7 2 -3.6 0.2 2.3 20 1.5 15 1 10 0.5 5 [degree] 2 0 -5 -1 -10 -1.5 -15 0.5 0.8 1.1 1.4 Freq [GHz] 0.8 1.1 1.4 Freq [GHz] 1.7 2 2.3 1.7 2 2.3 0 -0.5 -2 0.2 0.5 Phase balance Amplitude Balance [dB] -1.8 -21 1.7 2 2.3 1.7 2 2.3 -20 0.2 0.5 0.8 1.1 1.4 Freq [GHz] CMRR 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 -36 0.2 0.5 0.8 1.1 1.4 Freq [GHz] Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0322J5050AHF Rev F PRELIMINARY Typical Broadband Performance: 10 MHz to 8010 MHz Differential insertion loss 0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] [dB] Return Loss 0 -18 -1.8 -21 -2.1 -24 -2.4 -27 -2.7 -30 -3 -33 -3.3 -36 0.01 1.01 2.01 3.01 4.01 5.01 Freq [GHz] 6.01 7.01 -3.6 0.01 8.01 1.01 2.01 Amplitude Balance 7.01 8.01 6.01 7.01 8.01 20 1.5 15 1 10 0.5 5 [degree] [dB] 6.01 Phase balance 2 0 0 -0.5 -5 -1 -10 -1.5 -15 -2 0.01 3.01 4.01 5.01 Freq [GHz] 1.01 2.01 3.01 4.01 5.01 Freq [GHz] 6.01 7.01 8.01 6.01 7.01 8.01 -20 0.01 1.01 2.01 3.01 4.01 5.01 Freq [GHz] CMRR 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 -36 0.01 1.01 2.01 3.01 4.01 5.01 Freq [GHz] Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0322J5050AHF Rev F Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) Solder Resist 6x .41 4x .25 Plated thru holes to ground 3x Transmission lines .04 6x .33 .66 Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0322J5050AHF Rev F PRELIMINARY Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. 2.00 4.00 .25 1.75 3.50 8.00 2.41 1.00 1.60 4.00 Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282