B0922J7575A50

Model B0922J7575A50 Rev C Ultra Low Profile 0805 Balun 75Ω to 75Ω Balanced Description The B0922J7575A50 is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output locations on modern chipsets in an easy to use surface mount package covering dual polarized commercial Satellite bands 950 MHz –1450 MHz & 1650 MHz – 2150 MHz. The B0922J7575A50 is ideal for high volume manufacturing and delivers higher performance than traditional wire wound baluns. The B0922J7575A50 has an unbalanced port impedance of 75Ω and a 75Ω balanced port impedance*. This transformation enables single ended signals to be applied to differential ports on modern integrated chipsets. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0922J7575A50 is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°C) • • • • • • • • • • Features: 950 – 2150 MHz 0.7mm Height Profile 75 Ohm to 2 x 37.5 Ohm Low Insertion Loss Sat LNB Chipset Compliant Input to Output DC Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Parameter Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling Operating Temperature Min. 950 Typ. 75 75 15 0.8 1.0 3 25 Max 2150 12 1.1 1.4 9 2 +85 -55 Unit MHz Ω Ω dB dB dB Degrees dB Watts ºC * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) .079±.004 [2.00±0.10] Side View Bottom View (Far-side) .026 [0.65] .027±.002 [0.70±0.05] .039 [0.98] .049±.004 [1.25±0.10] Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation GND Unbalanced Port GND Balanced Port NC Balanced Port 6 5 6X .012 [0.30] 4 1 2 3 6X .009 [0.22] Dimensions are in Inches [Millimeters] Mechanical Outline Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model B0922J7575A50 Rev C Typical Performance: 600 MHz. to 2600 MHz. Return Loss - Input 0 -3 -6 -9 -12 -15 [dB] Insertion Loss 0 -0.3 -0.6 -0.9 -1.2 -1.5 [dB] -18 -21 -24 -27 -30 -33 -36 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 -1.8 -2.1 -2.4 -2.7 -3 -3.3 -3.6 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 Frequency [MHz] Frequency [MHz] Amplitude Balance 2 1.5 1 0.5 [dB] Phase Balance 20 15 10 5 deg 0 -0.5 -1 -1.5 -2 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 0 -5 -10 -15 -20 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 Frequency [MHz] Frequency [MHz] CMRR 0 -3 -6 -9 -12 -15 [dB] -18 -21 -24 -27 -30 -33 -36 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 Frequency [MHz] USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model B0922J7575A50 Rev C Wide Band Performance: 500 MHz. to 8000 MHz. Return Loss - Input 0 -3 -6 -9 -12 -15 [dB] Insertion Loss 0 -5 -10 [dB] -18 -21 -24 -27 -30 -33 -36 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 -15 -20 -25 -30 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 7500 Frequency [MHz] Frequency [MHz] Amplitude Balance 2 1.5 1 0.5 [dB] deg Phase Balance 20 15 10 5 0 -5 -10 -15 -20 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 0 -0.5 -1 -1.5 -2 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 Frequency [MHz] Frequency [MHz] CMRR 0 -3 -6 -9 -12 -15 [dB] -18 -21 -24 -27 -30 -33 -36 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 8000 8000 Model B0922J7575A50 Rev C Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Mounting Footprint 6X .016 [0.35] 4X .012 [0.30] Part Orientation (Top View) 6X .013 [0.33] 6X .002 [0.05] .026 [0.66] 3X Transmission Line Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint Plated thru holes to ground USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model B0922J7575A50 Rev C Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. ØA ØC ØD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] ØC 2.0 [50.8] ØD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model B0922J7575A50 Rev C USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing.