BD3150N50100AHF

Model BD3150N50100AHF Rev D PRELIMINARY Ultra Low Profile 0404 Balun 50Ω to 100Ω Balanced Description The BD3150N50100AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output locations on modern chipsets in an easy to use surface mount package covering the MMDS and the low end of the UWB frequency range. The BD3150N50100AHF is ideal for high volume manufacturing and delivers higher performance than traditional ceramic baluns. The BD3150N50100AHF has an unbalanced port impedance of 50 and a 100 balanced port impedance. This transformation enables single ended signals to be applied to differential ports on modern integrated chipsets. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The BD3150N50100AHF is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications: Specifications subject to change without notice. Features:           3100 – 5000 MHz 0.57mm Height Profile 50 Ohm to 2 x 50 Ohm Low Insertion Loss UWB & MMDS Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free Parameter Min. Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling @85C Power Handling @105C Operating Temperature 3100 13 ROOM (25C) Max Min. Typ. 5000 50 100 15 0.7 0.8 3 26 5000 10 0.9 1.5 7 1.0 0.6 +105 -55 Typ. 50 100 14 0.7 0.8 15 17 Max Unit 7000 MHz Ω Ω dB dB dB Degrees dB Watts Watts ºC 0.9 1.3 20 1.0 0.6 +105 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) Side View Bottom View (Far-side) .24 .57±.05 1.04±.10 3x .27 1 2 .24 3x .27 .30 .30 1.04±.10 .50 3x .25 3 4 3x .25 Pin Designation GND / DC Feed 1 + RF GND Dimensions are in Millimeters Mechanical Outline 2 Unbalanced Port 3 Balanced Port 4 Balanced Port Visit us at www.Anaren.com .50 Tolerances are Non-Cumulative USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD3150N50100AHF Rev D Typical Performance: 3 GHz to 7.2 GHz Differential insertion loss [dB] 3.6 4.2 4.8 5.4 6 Freq [GHz] Amplitude Balance 6.6 7.2 20 1.5 15 1 10 0.5 5 0 -0.5 [dB] 0 -0.3 -0.6 -0.9 -1.2 -1.5 -1.8 -2.1 -2.4 -2.7 -3 -3.3 -3.6 3 2 [degree] [dB] [dB] Return Loss 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 -36 3 -1.5 -15 4.2 4.8 5.4 Freq [GHz] CMRR 6 6.6 7.2 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 3 3.6 4.2 4.8 5.4 Freq [GHz] 6 6.6 7.2 Visit us at www.Anaren.com 3.6 4.2 4.8 5.4 6 Freq [GHz] Phase balance 6.6 7.2 6.6 7.2 -5 -10 3.6 4.2 0 -1 -2 3 3.6 -20 3 4.8 5.4 Freq [GHz] USA/Canada: Toll Free: Europe: Asia: 6 (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD3150N50100AHF Rev D PRELIMINARY Differential insertion loss 0 -0.3 -0.6 -0.9 -1.2 -1.5 -1.8 -2.1 -2.4 -2.7 -3 -3.3 -3.6 0.01 1.01 2.01 3.01 4.01 5.01 6.01 7.01 8.01 Freq [GHz] Phase balance 20 1.5 15 1 10 0.5 5 0 -0.5 [dB] [dB] Return Loss 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 -36 0.01 1.01 2.01 3.01 4.01 5.01 6.01 7.01 8.01 Freq [GHz] Amplitude Balance 2 [degree] [dB] [dB] Wide Band Performance: 0.01 GHz. to 8.01 GHz. 0 -5 -1 -10 -1.5 -15 -2 0.01 1.01 2.01 3.01 4.01 5.01 6.01 7.01 8.01 Freq [GHz] CMRR 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 0.01 1.01 2.01 3.01 4.01 5.01 6.01 7.01 8.01 Freq [GHz] -20 0.01 1.01 2.01 3.01 4.01 5.01 6.01 7.01 8.01 Freq [GHz] Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD3150N50100AHF Rev D Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. With No DC Bias 3x Transmission Line 3x .29 With DC Bias Plated thru hole to ground Plated thru hole to ground .33 3x Transmission Line 3x .29 .33 3x .29 .33 3x .29 .22 .50 .22 .50 .22 .22 .50 .50 Circuit Pattern Circuit Pattern Footprint Pad (s) Footprint Pad (s) Solder Resist Dimensions are in Millimeters Mounting Footprint Visit us at www.Anaren.com Solder Resist Dimensions are in Millimeters Mounting Footprint USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD3150N50100AHF Rev D PRELIMINARY Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282