C1015J5003AHF

Model C1015J5003AHF Rev B Ultra Low Profile 0805 3 dB, 90° Hybrid Coupler PRELIMINARY Description The C1015J5003AHF is a low cost, low profile sub-miniature high performance 3 dB coupler in an easy to use surface mount package. The C1015J5003AHF is ideal for balanced power and low noise amplifiers, plus signal distribution and other applications where low insertion loss and tight amplitude and phase balance are required. The C1015J5003AHF is available on tape and reel for pick and place high volume manufacturing. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability. All parts have been subjected to rigorous qualification testing and units are 100% RF tested. Detailed Electrical Specifications: Specifications subject to change without notice. Room (25C) Features:       1000 – 1500 MHz 0.7 mm Height Profile Surface Mountable Tape & Reel RoHS Compliant Halogen-Free Parameter Frequency Port Impedance Return Loss Isolation Insertion Loss* Amplitude Balance Phase Balance Power Handling @85C Operating Temperature Min 1000 17 20 Typ 50 20 25 0.5 0.84 3.8 -55 Max 1500 0.7 1.1 7 4 +85 Unit MHz Ω dB dB dB dB Degrees Watts ºC *Specification based on performance of unit properly installed on microstrip printed circuit boards with 50 Ω nominal impedance. Outline Drawing Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C1015J5003AHF Rev B Typical Broadband Performance: 500 MHz. to 6000 MHz. Insertion Loss (dB) 0 -5 -0.5 -10 -1 Insertion Loss (dB) Return Loss at Input Port (dB) Return Loss at Input Port (dB) 0 -15 -20 -1.5 -2 -25 -2.5 -30 -3 -3.5 -35 0.5 1 1.5 2 2.5 3 3.5 Freq [GHz] 4 4.5 5 5.5 0.5 6 1 1.5 2 20 1.5 15 1 10 0.5 0 -0.5 -15 2 2.5 3 3.5 Freq [GHz] 5 5.5 6 4.5 5 5.5 6 -5 -1.5 1.5 4.5 0 -10 1 4 5 -1 -2 0.5 3 3.5 Freq [GHz] Phase balance(degree) 2 Phase balance(degree) Amplitude Balance (dB) Amplitude Balance (dB) 2.5 4 4.5 5 5.5 6 4 4.5 5 5.5 6 -20 0.5 1 1.5 2 2.5 3 3.5 Freq [GHz] 4 Isolation (dB) 0 -5 Isolation (dB) -10 -15 -20 -25 -30 -35 0.5 1 1.5 2 2.5 3 3.5 Freq [GHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C1015J5003AHF Rev B Typical Performance: 900 MHz. to 1600 MHz. PRELIMINARY Insertion Loss (dB) Return Loss at Input Port (dB) 0 -5 -0.5 -10 -1 Insertion Loss (dB) Return Loss at Input Port (dB) 0 -15 -20 -2 -25 -2.5 -30 -3 -35 0.9 -3.5 1 1.1 1.2 1.3 Freq [GHz] 1.4 1.5 1.6 0.9 1 10 Phase balance(degree) 15 0.5 0 -0.5 1.5 1.6 1.4 1.5 1.6 -5 -1.5 -15 1.2 1.3 Freq [GHz] 1.4 0 -10 1.1 1.2 1.3 Freq [GHz] 5 -1 1 1.1 20 1.5 -2 0.9 1 Phase balance(degree) Amplitude Balance (dB) 2 Amplitude Balance (dB) -1.5 1.4 1.5 1.6 1.4 1.5 1.6 -20 0.9 1 1.1 1.2 1.3 Freq [GHz] Isolation (dB) 0 -5 Isolation (dB) -10 -15 -20 -25 -30 -35 0.9 1 1.1 1.2 1.3 Freq [GHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C1015J5003AHF Rev B Definition of Measured Specifications Parameter Return Loss Isolation Insertion Loss Definition Mathematical Representation i, j, k, m is denoted as the port index of input, isolated, direct and coupled port for specific pin configuration shown in the table The impedance match of the coupler to a 50 system. Return Loss is an alternate means to express VSWR. The input power divided by the sum of the power at the two output ports. The input power divided by the sum of the power at the two output ports. Amplitude Balance The difference in power between the two outputs. Phase Balance The difference in phase angle between the two output ports. 20log10 ( Sii ) 20log10 S ji 2 2 10log10 ( Smi  Ski ) 20 log10 ( Ski ) Smi Ski  Smi  90o *100% RF test is performed per spec definition for pin configuration 1 and port 1 (input port) is connected to pin1, port 2 (isolated port) is connected to pin 3, port 3 (direct port) is connected to pin 4 and port 4 (isolated) is connected to pin 6. Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C1015J5003AHF Rev B Mounting Configuration: PRELIMINARY In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. 6x 0.35 4x 0.30 6x 0.33 0.66 6x 0.05 4x Transmission Line Plated thru holes to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Millimeters Mounting Footprint Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C1015J5003AHF Rev B Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282