C1720J5003A00

Model C1720J5003A00 Rev D Ultra Low Profile 0805 3 dB, 90° Hybrid Coupler Description The C1720J5003A00 is a low cost, low profile sub-miniature high performance 3 dB coupler in an easy to use surface mount package. It is designed for PCS, DCS, DECT, and WCDMA-3G applications. The C1720J5003A00 is ideal for balanced power and low noise amplifiers, plus signal distribution and other applications where low insertion loss and tight amplitude and phase balance are required. The C1720J5003A00 is available on tape and reel for pick and place high volume manufacturing. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and o Y thermal coefficient of expansion (CTE) of 17 ppm/ C. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°C) Features: • • • • • • • • • 1700 – 2000 MHz 0.7mm Height Profile PCS, DCS, DECT, & WCDMA-3G Low Insertion Loss High Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Parameter Frequency Port Impedance Return Loss Isolation Insertion Loss* Amplitude Balance Phase Balance (relative to 90°) Power Handling Operating Temperature Min. 1700 21 24 Typ. 50 27 36 0.3 0.2 1 Max 2000 0.4 1.0 5 4 +85 Unit MHz Ω dB dB dB dB Degrees Watts ºC -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) .079±.004 [2.00±0.10] Side View Bottom View (Far-side) 4X .026 [0.65] .039 [0.98] 1 2 3 6X .009 [0.22] .028±.002 [0.700±0.05] .049±.004 [1.25±0.10] Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation Input GND Isolated Direct GND Coupled 6 5 6X .012 [0.30] 4 Dimensions are in Inches [Millimeters] Mechanical Outline Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model C1720J5003A00 Rev D Typical Broadband Performance: 500 MHz. to 6000 MHz. Return Loss - Input 0 -3 -6 -9 -12 -15 [dB] Insertion Loss 0.000 -0.300 -0.600 -0.900 -1.200 -1.500 [dB] -18 -21 -24 -27 -30 -33 -36 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 -1.800 -2.100 -2.400 -2.700 -3.000 -3.300 -3.600 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 5500 Frequency [MHz] Frequency [MHz] Amplitude Balance 2 1.5 1 0.5 [dB] deg Phase Balance 20 15 10 5 0 -5 -10 -15 -20 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 0 -0.5 -1 -1.5 -2 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 -15 [dB] -18 -21 -24 -27 -30 -33 -36 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency [MHz] USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. 6000 6000 Model C1720J5003A00 Rev D Typical Performance: 1600 MHz. to 2100 MHz. Return Loss - Input 0 -3 -6 -9 -12 [dB] Insertion Loss 0.0 -0.3 -0.6 -0.9 -1.2 -1.5 [dB] -15 -18 -21 -24 -27 -30 -33 -36 1600 1700 1800 1900 2000 2100 -1.8 -2.1 -2.4 -2.7 -3.0 -3.3 -3.6 1600 1700 1800 1900 2000 2100 2100 Frequency [MHz] Frequency [MHz] Amplitude Balance 2 1.5 1 0.5 [dB] Phase Balance 20 15 10 5 deg 0 -0.5 -1 -1.5 -2 1600 1700 1800 1900 2000 2100 0 -5 -10 -15 -20 1600 1700 1800 1900 2000 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 -15 [dB] -18 -21 -24 -27 -30 -33 -36 1600 1700 1800 1900 2000 2100 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model C1720J5003A00 Rev D Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. 6X .014 [0.35] 4X .012 [0.30] 6X .013 [0.33] 6X .002 [0.05] .026 [0.66] 4X Transmission Line Circuit Pattern Footprint Pad (s) Solder Resist Plated thru holes to ground Dimensions are in Inches [Millimeters] Mounting Footprint USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model C1720J5003A00 Rev D Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. ØA ØC ØD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] ØC 2.0 [50.8] ØD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model C1720J5003A00 Rev D USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing.