C2327J5003AHF

Model C2327J5003AHF Rev H Ultra Low Profile 0805 3 dB, 90° Hybrid Coupler Description The C2327J5003AHF is a low cost, low profile sub-miniature high performance 3 dB coupler in an easy to use surface mount package. It is designed for WiMax, WiBro, WiFi, ISM, and EUMTS applications. The C2327J5003AHF is ideal for balanced power and low noise amplifiers, plus signal distribution and other applications where low insertion loss and tight amplitude and phase balance are required. The C2327J5003AHF is available on tape and reel for pick and place high volume manufacturing. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability. All parts have been subjected to rigorous qualification testing and units are 100% RF tested . Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25C) Features:           2300 – 2700 MHz 0.7mm Height Profile WiMax, WiBro, WiFi & ISM Low Insertion Loss High Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen-free Parameter Min. Frequency Port Impedance Return Loss Isolation Insertion Loss* Amplitude Balance Phase Balance (relative to 90°) Power Handling @85C Power Handling @105C Operating Temperature 2300 15 18 Typ. 50 18 22 0.3 0.1 4 -55 Max Unit 2700 MHz Ω dB dB dB dB Degrees Watts Watts ºC 0.4 0.9 8 4 2.4 +140 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C2327J5003AHF Rev H Typical Broadband Performance: 500 MHz. to 6000 MHz. Insertion Loss -3 -0.300 -6 -0.600 -9 -0.900 -12 -1.200 -15 -1.500 4500 6000 5 4500 4000 3500 3000 2500 2000 1500 -20 6000 -2 5500 -15 5000 -1.5 4500 -10 4000 -1 1000 0 -5 500 0 -0.5 3500 6000 0.5 3000 5500 10 2500 5500 1 2000 5000 15 deg 2 1.5 1500 4000 Phase Balance 20 1000 5000 Amplitude Balance 500 3500 Frequency [MHz] Frequency [MHz] [dB] 3000 2500 500 6000 5500 5000 4500 4000 3500 -3.600 3000 -3.300 -36 2500 -3.000 -33 2000 -2.700 -30 1500 -2.400 -27 1000 -2.100 -24 2000 -1.800 -21 1500 -18 1000 [dB] 0.000 500 [dB] Return Loss - Input 0 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 -36 500 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C2327J5003AHF Rev H Typical Performance: 2200 MHz. to 2800 MHz. Insertion Loss Return Loss - Input 0.0 0 -0.3 -6 -0.6 -0.9 -1.2 -15 -1.5 Frequency [MHz] 2800 2700 Frequency [MHz] Phase Balance Amplitude Balance 20 15 1 10 0.5 5 Frequency [MHz] 2800 2800 2700 2600 2500 -20 2400 -15 -2 2300 -10 2200 -1 -1.5 2700 -5 2600 -0.5 2500 0 2400 0 2300 deg 1.5 2200 2 [dB] 2600 2200 2800 -3.6 2700 -3.3 -36 2600 -3.0 -33 2500 -2.7 -30 2400 -2.4 -27 2300 -2.1 -24 2500 -1.8 -21 2400 -18 2300 [dB] -9 -12 2200 [dB] -3 Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 2800 2700 2600 2500 2400 2300 -36 2200 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C2327J5003AHF Rev H Definition of Measured Specifications Parameter Return Loss Isolation Insertion Loss Definition Mathematical Representation i, j, k, m is denoted as the port index of input, isolated, direct and coupled port for specific pin configuration shown in the table The impedance match of the coupler to a 50 system. Return Loss is an alternate means to express VSWR. The input power divided by the sum of the power at the two output ports. The input power divided by the sum of the power at the two output ports. Amplitude Balance The difference in power between the two outputs. Phase Balance The difference in phase angle between the two output ports. 20 log10 ( Sii ) 20log10 S ji 2 2 10log10 ( S mi  S ki ) 20log10 ( Ski ) Smi S ki  S mi  90 o *100% RF test is performed per spec definition for pin configuration 1 and port 1 (input port) is connected to pin1, port 2 (isolated port) is connected to pin 3, port 3 (direct port) is connected to pin 4 and port 4 (isolated) is connected to pin 6. Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C2327J5003AHF Rev H Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. 6x 0.35 4x 0.30 6x 0.33 0.66 6x 0.05 4x Transmission Line Plated thru holes to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Millimeters Mounting Footprint Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C2327J5003AHF Rev H Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 10,000 per reel. 2.00 .25 4.00 1.75 3.50 8.00 1.60 2.41 .81 4.00 Direction of Part Feed (Unloading) Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282