C3337J5003AHF

Model C3337J5003AHF Rev H PRELIMINARY Ultra Low Profile 0805 3 dB, 90° Hybrid Coupler Description The C3337J5003AHF is a low cost, low profile sub-miniature high performance 3 dB coupler in an easy to use surface mount package. It is designed for LTE, WiMax and WiBro applications. The C3337J5003AHF is ideal for balanced power and low noise amplifiers, plus signal distribution and other applications where low insertion loss and tight amplitude and phase balance are required. The C3337J5003AHF is available on tape and reel for pick and place high volume manufacturing. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability. All parts have been subjected to rigorous qualification testing and units are 100% RF tested. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25C) Features:  3070 – 3900 MHz  0.7mm Height Profile  High Isolation, Low Loss  LTE Bands: 22, 42, 43  WiMax WiBro Applications  Surface Mountable  Tape & Reel  Non-conductive Surface  RoHS Compliant  Halogen-Free  100% RF Tested  -55°C to 105°C Parameter Min. Typ. Max Min. Typ. Max Min. Typ. Max Unit MHz Frequency 3300 3700 3070 3805 3300 3900 Ω Port Impedance 50 50 50 dB Return Loss 15 18 15 18 15 18 dB Isolation 18 22 18 22 18 22 dB Insertion Loss 0.2 0.3 0.2 0.4 0.2 0.3 dB Amplitude Balance 0.3 1 0.3 1.2 0.3 1 Degrees Phase Balance (relative to 90°) 3 7 4 7 3 7 ns Group Delay 0.05 0.055 0.06 0.05 0.06 0.07 0.05 0.055 0.06 Watts Power Handling (85ºC) 4 4 4 Watts Power Handling (105 ºC) 3 3 3 ºC Operating Temperature -55 105 -55 105 -55 105 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Nearside) 2.04±0.10 Bottom View (Farside) Side View 4x 0.37 0.68±0.07 1 2 3 2x 0.15 1.29±0.10 6x 0.98 6x 0.22 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location 6 5 4 4x 0.65 6x 0.30 Pin 1 2 3 4 5 6 Configuration-1 Input GND Isolated Direct GND Coupled Configuration-2 Isolated GND Input Coupled GND Direct Configuration-3 Direct GND Coupled Input GND Isolated Configuration-4 Coupled GND Direct Isolated GND Input Visit us at www.anaren.com Mechanical Outline -Dimensions are in Millimeters -Tolerances are Non-Cumulative USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C3337J5003AHF Rev H Typical Broadband Performance: 10 MHz to 8010 MHz Return Loss at Input Port Insertion Loss 0 0 -5 -0.3 -0.6 -10 -0.9 -15 -1.2 [dB] -1.5 -25 -1.8 -2.1 -30 -2.4 -35 -2.7 -40 -3 -45 -50 0.01 -3.3 1.01 2.01 3.01 4.01 5.01 Freq [GHz] 6.01 7.01 -3.6 0.01 8.01 1.01 2.01 Amplitude Balance (dB) 20 1.5 15 1 10 0.5 5 0 -5 -1 -10 -1.5 -15 1.01 2.01 3.01 4.01 5.01 Freq [GHz] 4.01 5.01 Freq [GHz] 6.01 7.01 8.01 6.01 7.01 8.01 0 -0.5 -2 0.01 3.01 Phase Balance 2 [degree] [dB] -20 6.01 7.01 8.01 6.01 7.01 8.01 -20 0.01 1.01 2.01 3.01 4.01 5.01 Freq [GHz] Isolation (dB) 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 -36 0.01 1.01 2.01 3.01 4.01 5.01 Freq [GHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C3337J5003AHF Rev H PRELIMINARY Typical Performance: 2900 MHz to 3900 MHz Insertion Loss Return Loss at Input Port 0 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] -3 -18 -1.8 -21 -2.1 -24 -2.4 -27 -2.7 -30 -3 -33 -3.3 -36 2.9 3.1 3.3 3.5 Freq [GHz] 3.7 -3.6 2.9 3.9 20 1.5 15 1 10 0.5 5 0 -5 -1 -10 -1.5 -15 3.1 3.3 3.5 Freq [GHz] 3.3 3.5 Freq [GHz] 3.7 3.9 3.7 3.9 0 -0.5 -2 2.9 3.1 Phase Balance Amplitude Balance (dB) 2 [degree] [dB] 0 3.7 3.9 3.7 3.9 -20 2.9 3.1 3.3 3.5 Freq [GHz] Isolation (dB) 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 -36 2.9 3.1 3.3 3.5 Freq [GHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C3337J5003AHF Rev H Definition of Measured Specifications Mathematical Representation Parameter Return Loss Isolation Insertion Loss Definition i, j, k, m is denoted as the port index of input, isolated, direct and coupled port for specific pin configuration shown in the table The impedance match of the coupler to a 50 system. Return Loss is an alternate means to express VSWR. The input power divided by the sum of the power at the two output ports. The input power divided by the sum of the power at the two output ports. Amplitude Balance The difference in power between the two outputs. Phase Balance The difference in phase angle between the two output ports. Group Delay Group delay is defined as the average of the mean group delay of the coupling path and the mean group delay of the direct path. 20log10 ( Sii ) 20log10 S ji 2 2 10log10 ( Smi  Ski ) 20log10 ( Ski ) Smi Ski  Smi  90o Group delay (ns) = Mean  GD  Smi    Mean  GD  Ski   2 where " Mean " is the arithmetic mean of the group delay over a frequency band. *100% RF test is performed per spec definition for pin configuration 1 and port 1 (input port) is connected to pin1, port 2 (isolated port) is connected to pin 3, port 3 (direct port) is connected to pin 4 and port 4 (isolated) is connected to pin 6. Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C3337J5003AHF Rev H PRELIMINARY Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. 6x 0.35 4x 0.30 6x 0.33 0.66 6x 0.05 4x Transmission Line Plated thru holes to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Millimeters Mounting Footprint Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model C3337J5003AHF Rev H Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 10,000 per reel. Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282