PD0409J7575S2HF

Model PD0409J7575S2HF Rev B Ultra Low Profile 0805 Power Divider 75Ω to 75Ω Description: The PD0409J7575S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD0409J7575S2HF is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD0409J7575S2HF is matched to 75 Ω and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: GSM, WCDMA, DVB-H (Europe) and Terrestrial TV. The PD0409J7575S2HF does not include the resistive element and therefore, requires an external resistor for operation. The PD0409J7575S2HF is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°C) Features: • • • • • • • • • • • • 400-900 MHz 9.3 dB Isolation (output ports) Good Return Loss 0.5mm Height Profile 75Ω Input / 75Ω Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant External Resistor Required Halogen Free Parameter Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Min. 400 Operating Temperature -55 10 8.2 Typ. Max 900 75 75 12 0.5 0.1 1 9.3 2 Unit MHz Ω Ω dB dB dB Degrees dB Watts +85 ºC 0.6 0.6 3 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing: TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 0.54±0.05 1 2 3 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 4x 0.65 5 4 6x 0.30 Designation GND Input GND Output 1 GND Output 2 1 Model PD0409J7575S2HF Rev B Typical Broadband Performance: 500 MHz. to 8.0 GHz. Return Loss - Input Insertion Loss 0 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 [dB] [dB] -9 -18 6000 6500 7000 7500 8000 7000 7500 8000 5000 5000 4500 4000 3500 3000 2500 2000 1500 8000 7500 7000 6500 6000 5500 5000 -20 4500 -15 -2 4000 -10 3500 -1 -1.5 1000 -5 500 0 -0.5 3000 6500 5 0 2500 5500 10 0.5 2000 6000 15 1 deg 1.5 1500 4500 Phase Balance 20 500 5500 Amplitude Balance 2 1000 4000 Frequency [MHz] Frequency [MHz] [dB] 3500 3000 2500 2000 1500 500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 -36 2500 -33 -36 2000 -30 -33 1500 -27 -30 1000 -24 -27 500 -21 -24 1000 -18 -21 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 -36 Frequency [MHz] 2 Model PD0409J7575S2HF Rev B Typical Performance: 300 MHz. to 1000 MHz. Return Loss - Input Insertion Loss 0.0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] [dB] 0 -18 -21 -1.8 -2.1 -24 -2.4 -27 -2.7 -3.0 -30 -3.3 -33 1.5 15 1 10 0.5 5 1000 900 1000 900 800 700 1000 900 800 -20 700 -15 -2 600 -10 500 -1 -1.5 600 -5 500 0 -0.5 400 0 300 deg 20 400 800 Phase Balance Amplitude Balance 2 300 700 Frequency [MHz] Frequency [MHz] [dB] 600 500 300 1000 900 800 700 600 500 400 300 400 -3.6 -36 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 1000 900 800 700 600 500 400 300 -36 Frequency [MHz] 3 Model PD0409J7575S2HF Rev B Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD0409J7575S2HF is a Wilkinson power divider, an external 0603 150Ω resistor must be mounted in locations R1 as shown in the Figure below. Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) 3x Transmission lines Solder Resist 3x Plated thru holes to ground 6x .33 .04 6x .41 4x .25 .66 R1 4 Model PD0409J7575S2HF Rev B Packaging and Ordering Information: Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Contact us: rf&s_support@ttm.com 5