PD0922J5050D2HF

Model PD0922J5050D2HF Rev D Ultra Low Profile Halogen Free 0404 Balun 50Ω to 100Ω Balanced Description: The PD0922J5050D2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package and is ideal for high volume manufacturing while delivering higher performances than traditional printed and lumped element solutions. It has been designed for the following markets: DVB-S, GSM, DCS, PCS, CDMA and GPS. The PD0922J5050D2HF is matched to 50 Ω and has a height profile of 0.8 mm which is ideal for high level integrations. A 2 section Wilkinson design results in increased isolation performance. Two external resistors are required for operation. Components are available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. Features: • • • • • • • • • • • • 950 – 2150 MHz 12dB Isolation (output ports) Good Return Loss 0.8mm Height Profile 50Ω Outputs/Inputs External resistors required Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free ROOM (25°C) Parameter Min. Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling @85oC @105oC Operating Temperature 950 9.3 10.5 Typ. 50 50 11 0.7 0.1 1 12 Max Unit 2150 MHz Ω Ω dB dB dB Degrees dB 0.8 0.5 3 2 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) 1.2 +140 Watts ºC Outline Drawing: TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 0.85±0.08 3 2 1 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 4x 0.65 5 4 6x 0.30 Designation Output 1 Input Mid 2 Mid 1 GND Output 2 1 Model PD0922J5050D2HF Rev D Typical Broadband Performance: 500 MHz. to 8.5 GHz. 2 Model PD0922J5050D2HF Rev D Typical Performance: 600 MHz. to 2600 MHz. 3 Model PD0922J5050D2HF Rev D Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD0922J5050D2HF is a Wilkinson power divider, external 0402 100Ω and 200Ω resistors must be mounted in locations R1 and R2 respectively, as shown in the Figure below. Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) Solder Resist 3x Transmission lines .04 R1 4x .25 .66 R2 6x .41 6x .33 Plated thru holes to ground 4 Model PD0922J5050D2HF Rev D Packaging and Ordering Information: Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Contact us: rf&s_support@ttm.com 5