PD0922J5050S2HF

Model PD0922J5050S2HF Rev D Ultra Low Profile 0805 Power Divider Ultra Low 50Ω to 50Ω Description: The PD0922J5050S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD0922J5050S2HF is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD0922J5050S2HF is matched to 50 Ω and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: DVB-S, DVB-H (USA), GSM, DCS, PCS, CDMA, 3G and GPS. The PD0922J5050S2HF does not include the resistive element and therefore, requires an external resistor for operation. The PD0922J5050S2HF is available on tape and reel for high volume manufacturing pick and place Detailed Electrical Specifications: Specifications subject to change without notice. Features: • • • • • • • • • • • • 950-2150 MHz 10dB Isolation (output ports) High Return Loss 0.5mm Height Profile 50Ω Input / 50Ω Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant External resistor required Halogen Free ROOM (25°C) Parameter Min. Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling@85oC @105oC 950 10.4 9 Operating Temperature Typ. 50 50 12 0.5 0.1 1 10 Max Unit 2150 MHz Ω Ω dB dB dB Degrees dB 0.8 0.3 3 2 1.2 -55 +140 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Watts ºC Outline Drawing: TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 0.54±0.05 3 2 1 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 4x 0.65 5 4 6x 0.30 Designation GND Input GND Output 1 GND Output 2 1 Model PD0922J5050S2HF Rev D Typical Broadband Performance: 500 MHz. to 6.0 GHz. Return Loss - Input Insertion Loss 0 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 [dB] [dB] -9 -18 -18 -21 -21 -24 -24 -27 -27 -30 -30 -33 -33 1.5 15 1 10 0.5 5 6000 5500 4500 5000 6000 5500 5000 4500 4000 3500 3000 2500 6000 5500 5000 4500 4000 3500 3000 -20 2500 -15 -2 2000 -10 1500 -1 -1.5 2000 -5 1500 0 -0.5 500 0 1000 deg 20 1000 4000 Phase Balance Amplitude Balance 2 500 3500 Frequency [MHz] Frequency [MHz] [dB] 3000 2500 2000 1500 500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 1000 -36 -36 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 -36 Frequency [MHz] 2 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 [dB] Frequency [MHz] -10 -15 -2 -20 2600 -1 -1.5 2500 -5 2400 -0.5 2300 5 2200 10 0.5 2100 15 1 2000 1.5 1900 20 1800 Amplitude Balance 1700 Frequency [MHz] 1600 2 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 Return Loss - Input 1500 -3.6 1200 -3.3 -36 1400 -3.0 -33 1300 -2.7 -30 1100 -2.4 -27 1200 -2.1 -24 1100 -21 900 -1.5 1000 -1.2 -15 1000 -0.9 -12 800 -0.6 -9 700 -0.3 -6 [dB] -3 900 600 [dB] 0.0 800 0 deg 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 0 700 [dB] -18 600 2600 2500 2400 2300 2200 2100 2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 Model PD0922J5050S2HF Rev D Typical Performance: 600 MHz. to 2600 MHz. Insertion Loss -1.8 Frequency [MHz] Phase Balance 0 Frequency [MHz] 0 Isolation -3 -12 -6 -15 -9 -18 -21 -27 -24 -30 -33 -36 Frequency [MHz] 3 Model PD0922J5050S2HF Rev D Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD0922J5050S2HF is a Wilkinson power divider, an external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) 3x Transmission lines Solder Resist 3x Plated thru holes to ground 6x .33 .04 6x .41 4x .25 .66 R1 4 Model PD0922J5050S2HF Rev D Packaging and Ordering Information: Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Contact us: rf&s_support@ttm.com 5