PD0922J7575D2HF
Rev D
Ultra Low Profile 0805 Power Divider
75Ω to 75Ω
Description:
The PD0922J7575D2HF is a low profile, sub-miniature Wilkinson power
divider in an easy to use surface mount package and is ideal for high volume
manufacturing while delivering higher performances than traditional printed
and lumped element solutions. It has been designed for the following
markets: DVB-S, GSM, DCS, PCS, WCDMA, GPS, 802.11a+g, Bluetooth,
and Zigbee USA.
The PD0922J7575D2HF is matched to 75Ω and has a height profile of
0.8 mm. A two section Wilkinson design results in increased isolation
performance. Two external resistors are required for operation. Components
are available on tape and reel for high volume manufacturing pick and place.
Detailed Electrical Specifications:
Specifications subject to change without notice.
Features:
•
•
•
•
•
•
•
•
•
•
•
•
950 – 2150 MHz
16 dB Isolation (output ports)
Good Return Loss
0.8mm Height Profile
75Ω Outputs/Inputs
External resistors required
Low Insertion Loss
Surface Mountable
Tape & Reel
Non-conductive Surface
RoHS Compliant
Halogen Free
ROOM (25°C)
Parameter
Frequency
Input Port Impedance
Output Port Impedance
Return Loss
Insertion Loss*
Amplitude Balance
Phase Balance
Isolation (Output Ports)
Power Handling
Operating Temperature
Min.
Typ.
950
9.5
14
-55
*Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
75
75
11
0.8
0.4
2
16
Max
Unit
2150
MHz
Ω
Ω
dB
dB
dB
Degrees
dB
Watts
ºC
1.0
0.7
3
2
+85
Outline Drawing:
1
PD0922J7575D2HF
Rev D
Typical Broadband Performance: 500 MHz. to 8.0 GHz.
2
PD0922J7575D2HF
Rev D
Typical Performance: 900 MHz. to 2200 MHz.
3
PD0922J7575D2HF
Rev D
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must
be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may
not meet published specifications.
All of the Xinger components are constructed from organic PTFE based composites which possess excellent
electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green
standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier.
An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the
transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as
varying pick and place equipment tolerances. In addition, since the PD0922J7575D2HF is a Wilkinson power
divider, external 0402 150Ω and 300Ω resistors must be mounted in locations R1 and R2 respectively, as
shown in the Figure below.
Pad Footprint w 0402 Resistor Locations:
4
PD0922J7575D2HF
Rev D
Packaging and Ordering Information:
Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown
below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information.
Contact us:
rf&s_support@ttm.com
5
很抱歉,暂时无法提供与“PD0922J7575D2HF”相匹配的价格&库存,您可以联系我们找货
免费人工找货