PD1722J5050S3HF

PD1722J5050S3HF Rev E Ultra Low Profile 0805 Power Divider 3 Way 50Ω to 50Ω Description: The PD1722J5050S3HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package and is ideal for high volume manufacturing while delivering higher performances than traditional printed and lumped element solutions. It has been designed for the DCS, PCS, UMTS and CDMA markets. The PD1722J5050S3HF is matched to 50 Ω and has a height profile of 0.79 mm. Three external resistors are required for operation. Components are available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. Features: • • • • • • • • • • • 1700 – 2200 MHz 0.82 mm Height Profile 50Ω Outputs/Inputs DCS/PCS/UMTS/CDMA External resistors required Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free ROOM (25°C) Parameter Min. Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature 1700 9 14 Typ. 50 50 11 0.9 0.5 9 17 Max Unit 2200 MHz Ω Ω dB dB dB Degrees dB Watts ºC 1.3 0.9 12 1 +85 -55 *Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing: TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 0.79±0.08 3 2 1 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 4x 0.65 5 4 6x 0.30 Designation GND Input Output 1 Output 2 GND Output 3 1 PD1722J5050S3HF Rev E Typical Performance: 500 MHz. to 8.5 GHz. Insertion Loss 0 -3 -3 -6 -6 -9 -9 -12 -12 -15 -15 [dB] -18 -21 -18 Frequency [MHz] 1.500 15.0 1.000 10.0 0.500 5.0 8500 8000 7500 7000 6500 6000 5000 5500 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -15 -18 -21 -24 -27 -30 -33 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 500 -36 1000 [dB] -12 Frequency [MHz] 2 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 8500 8000 7500 7000 6500 6000 5500 5000 4500 -20.0 4000 -2.000 3500 -15.0 3000 -10.0 -1.500 2500 -1.000 2000 -5.0 1500 -0.500 1500 0.0 500 0.000 1000 deg 20.0 1000 4500 Phase Balance 2.000 500 4000 Frequency [MHz] Amplitude Balance [dB] 3500 3000 2500 2000 500 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 -36 2000 -33 -36 1500 -30 -33 500 -27 -30 1000 -24 -27 1500 -21 -24 1000 [dB] Return Loss - Input 0 PD1722J5050S3HF Rev E Wide Band Performance: 1600 MHz. to 2300 MHz. Return Loss 0 Insertion Loss 0.0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 [dB] -15 [dB] -18 -21 -1.5 -1.8 -2.1 -24 -2.4 -27 1.0 10.0 0.5 5.0 Frequency [MHz] 2300 2300 2000 1900 -20.0 1800 -15.0 -2.0 2300 -1.5 2200 -10.0 2100 -5.0 -1.0 2000 -0.5 1700 0.0 1600 0.0 1900 2200 15.0 1800 2200 1.5 deg 20.0 1700 2100 Phase Balance 2.0 1600 2000 Frequency [MHz] Amplitude Balance [dB] 2100 Frequency [MHz] 1900 1800 1600 2300 2200 2100 2000 1900 1800 -3.6 1700 -3.3 -36 1600 -3.0 -33 1700 -2.7 -30 Frequency [MHz] Isolation 0.00 -3.00 -6.00 -9.00 -12.00 [dB] -15.00 -18.00 -21.00 -24.00 -27.00 -30.00 -33.00 2300 2200 2100 2000 1900 1800 1700 1600 -36.00 Frequency [MHz] 3 PD1722J5050S3HF Rev E Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thickness as well as varying pick and place equipment tolerances. In addition, since the PD1722J5050S3HF is a Wilkinson power divider, external 0402 100Ω resistors must be mounted must be mounted as shown in the Figure below. Pad Footprint w/ 0402 Resistor Locations 4 PD1722J5050S3HF Rev E Packaging and Ordering Information: Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. Contact us: rf&s_support@ttm.com 5