PD2328J5050S2HF

PD2328J5050S2HF Rev E Ultra Low Profile 0805 Power Divider 50Ω to 50Ω Description: The PD2328J5050S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD2328J5050S2HF is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD2328J5050S2HF is matched to 50 Ω and has a height profile of 0.5 mm, which is ideal for high-level integrations in the following markets: WiMAX, 802.11b & g, Bluetooth, ZigBee, and XM & Sirius radio. The PD2328J5050S2HF does not include the resistive element and therefore, requires an external resistor for operation. The PD2328J5050S2HF is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. Features: 2300-2800 MHz 21 dB Isolation (output ports) Good Return Loss 0.5mm Height Profile 50Ω Input / 50Ω Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant • External Resistor Required • Halogen Free • • • • • • • • • • ROOM (25°C) Parameter Min. Typ. Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling @85C Operating Temperature 2300 Max Unit 2800 MHz Ω Ω dB dB dB Degrees dB Watts ºC 50 50 19 0.3 0.1 1 21 15 17 0.5 0.3 2 2 +105 -55 *Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC Outline Drawing: TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 0.53±0.05 3 2 1 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 4x 0.65 5 4 6x 0.30 Designation GND Input GND Output 1 GND Output 2 1 PD2328J5050S2HF Rev E Typical Broadband Performance: 500 MHz. to 8.0 GHz. Return Loss - Input Insertion Loss 0 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 7500 8000 8000 5500 5000 6000 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 8000 7500 7000 6500 -20 6000 -15 -2 5500 -1.5 5000 -10 4500 -5 -1 4000 -0.5 1000 0 500 0 3500 7000 5 3000 7500 10 2500 6500 1 0.5 2000 7000 15 1500 6500 1.5 deg 2 20 1000 4500 Phase Balance Amplitude Balance 500 4000 Frequency [MHz] Frequency [MHz] [dB] 3500 3000 2500 500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 -36 2500 -33 -36 2000 -30 -33 1500 -27 -30 500 -24 -27 1000 -21 -24 2000 -18 -21 1500 -18 1000 [dB] [dB] -9 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 500 1000 -36 Frequency [MHz] 2 PD2328J5050S2HF Rev E Typical Performance: 2200 MHz. to 2900 MHz. Return Loss - Input Insertion Loss 0.0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] [dB] 0 -18 -21 -1.8 -2.1 -24 -2.4 -27 -2.7 -30 -3.0 -33 -3.3 1 10 0.5 5 Frequency [MHz] 2900 2900 -20 2600 -2 2900 -15 2800 -10 2700 -1 -1.5 2500 -5 2400 -0.5 2300 0 2200 0 2600 2800 15 2500 2800 20 deg 2 2400 2700 Phase Balance 1.5 2300 2700 Amplitude Balance 2200 2600 Frequency [MHz] Frequency [MHz] [dB] 2500 2400 2200 2900 2800 2700 2600 2500 2400 2300 2200 2300 -3.6 -36 Frequency [MHz] Isolation 0 -3 -6 -9 -15 -18 -21 -24 -27 -30 -33 2900 2800 2700 2600 2500 2400 2300 -36 2200 [dB] -12 Frequency [MHz] 3 PD2328J5050S2HF Rev E Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD2328J5050S2HF is a Wilkinson power divider, an external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below. Pad Footprint w/ 0603 Resistor Locations Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) 3x Transmission lines Solder Resist 3x Plated thru holes to ground .04 6x .33 6x .41 4x .25 .66 R1 4 PD2328J5050S2HF Rev E Packaging and Ordering Information: Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. Contact us: rf&s_support@ttm.com 5