PD3150J5050S2HF

PD3150J5050S2HF Rev J Ultra Low Profile 0805 Power Divider 50Ω to 50Ω Description: The PD3150J5050S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD3150J5050S2HF is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD3150J5050S2HF is matched to 50Ω and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: DVB-S, GSM, DCS, PCS, WCDMA and GPS, 802.11a+g, Bluetooth, and Zigbee USA. The PD3150J5050S2HF does not include the resistive element and therefore, requires an external resistor for operation. The PD3150J5050S2HF is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specification subject to change without notice. Features: • • • • • • • • • • 2300-5000 MHz 0.5mm Height Profile 50Ω Input / 50Ω Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free External Resistor required ROOM (25°C) Parameter Min. Typ. Max Min. Typ. Max Min. Typ. Max Frequency 2300 Input Port Impedance Output Port Impedance Return Loss 6 Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) 11 Power Handling@105oC Operating Temperature -55 3800 3400 50 50 7 1.0 0.3 1 13 10 1.6 0.5 4 17 3 +140 3800 3100 50 50 15 0.4 0.1 0.5 25 -55 *Insertion loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) 6.3 1.0 0.4 2 13 3 +140 -55 Unit 5000 50 50 8.6 1.0 0.1 1 15 MHz Ω Ω dB 1.6 dB 0.4 dB 2 Degrees dB 3 Watts ºC +140 Outline Drawing: TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 0.53±0.05 3 2 1 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 4x 0.65 5 4 6x 0.30 Designation GND Input GND Output 1 GND Output 2 1 PD3150J5050S2HF Rev J Typical Broadband Performance: 500 MHz. to 8.0 GHz. Insertion Loss 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 Isolation 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 500 1000 -36 Frequency [MHz] 2 8000 7500 7000 Frequency [MHz] Frequency [MHz] [dB] 8000 7500 7000 5000 5000 4500 4000 3500 3000 2500 2000 1500 8000 7500 7000 6500 -20 6000 -2 5500 -15 5000 -10 4500 -1 -1.5 1000 0 -5 500 0 -0.5 4000 6500 5 3500 6500 0.5 3000 6000 10 2500 6000 1 2000 5500 15 1500 5500 1.5 deg 20 1000 4500 Phase Balance Amplitude Balance 2 500 4000 Frequency [MHz] Frequency [MHz] [dB] 3500 3000 2500 500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 -36 3000 -33 -36 2500 -30 -33 2000 -27 -30 1500 -24 -27 500 -21 -24 2000 -18 -21 1500 -18 1000 [dB] -9 1000 [dB] Return Loss - Input 0 5100 5000 4900 4800 4700 4600 4500 4400 4300 4200 4100 4000 3900 3800 3700 3600 3500 3400 3300 3200 3100 3000 [dB] Frequency [MHz] -1.5 -15 -2 -20 Frequency [MHz] Isolation -3 0 -6 -12 -9 -15 -18 -21 -24 -27 -30 -33 -36 Frequency [MHz] 3 5100 -10 5000 -5 -1 4900 -0.5 4800 5 4700 10 4600 1 0.5 4500 15 4400 1.5 4300 20 4200 Amplitude Balance 4100 2 4000 Frequency [MHz] 3900 5100 5000 4900 4800 4700 4600 4500 4400 4300 4200 4100 4000 3900 3800 -3.6 3700 -3.3 -36 3800 -3.0 -33 3600 Return Loss - Input 3700 -2.7 -30 3500 -2.4 -27 3600 -2.1 -24 3400 -21 3500 -1.5 3300 -1.2 -15 3400 -0.9 -12 3200 -0.6 -9 3300 -0.3 -6 3100 -3 3200 3000 0.0 [dB] 0 3100 0 deg 5100 5000 4900 4800 4700 4600 4500 4400 4300 4200 4100 4000 3900 3800 3700 3600 3500 3400 3300 3200 3100 3000 [dB] -18 3000 5100 5000 4900 4800 4700 4600 4500 4400 4300 4200 4100 4000 3900 3800 3700 3600 3500 3400 3300 3200 3100 3000 [dB] PD3150J5050S2HF Rev J Typical Performance: 3000 MHz. to 5100 MHz. Insertion Loss -1.8 Frequency [MHz] Phase Balance 0 PD3150J5050S2HF Rev J Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD3150J5050S2HF is a Wilkinson power divider, an external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below. Pad Footprint w/ 0603 Resistor Locations Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) 3x Transmission lines Solder Resist 3x Plated thru holes to ground .04 6x .33 6x .41 4x .25 .66 R1 4 PD3150J5050S2HF Rev J Packaging and Ordering Information: Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. 2.00 .25 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .81 Direction of Part Feed (Unloading) Contact us: rf&s_support@ttm.com 5