PD6080J5050S2HF

PD6080J5050S2HF Rev E Ultra Low Profile 0805 Power Divider 50Ω to 50Ω Description: The PD6080J5050S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD6080J5050S2HF is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD6080J5050S2HF is matched to 50 Ω and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: RFID, fixed satellite, and mobile satellite. The PD6080J5050S2HF does not include the resistive element and therefore, requires an external resistor for operation. The PD6080J5050S2HF is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. Features: • • • • • • • • • • • 6000 – 8000 MHz 15dB Isolation (output ports) Good Return Loss 0.5mm Height Profile 50Ω Outputs/Inputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free ROOM (25°C) Parameter Min. Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling @85oC Operating Temperature 6000 Typ. 50 50 12 0.6 0.2 2 15 9 12 Max Unit 8000 MHz Ω Ω dB dB dB Degrees dB Watts ºC 0.9 0.5 5 2 +105 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing: TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 0.44±0.04 3 2 1 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 4x 0.65 5 4 6x 0.30 Designation GND Input GND Output 1 GND Output 2 1 PD6080J5050S2HF Rev E Typical Performance: 10 MHz. to 8.01 GHz. Insertion Loss Return Loss - Input 0 0.0 -3 -6 -0.4 -0.7 -1.1 -12 -15 -1.4 [dB] -18 -21 -24 -1.8 -2.2 -2.5 -27 -2.9 -30 -33 -3.2 20 1.5 15 1.0 10 0.5 5 [Deg] 2.0 8010 7510 7010 6510 6010 5510 5010 8010 7510 7010 6510 6010 5510 5010 4510 4010 3510 3010 2510 2010 1510 10 8010 7510 7010 6510 6010 5510 5010 4510 4010 3510 3010 2510 -20 2010 -15 -2.0 1510 -10 -1.5 1010 -1.0 10 -5 1010 0 -0.5 510 0.0 510 4510 Phase Balance Amplitude Balance [dB] 4010 Frequency [MHz] Frequency [MHz] Frequency [MHz] Frequency [MHz] PD6080J5050S2HF Power Derating Curve Isolation 4.0 0 6000-8000MHz 3.5 -3 -6 3.0 -9 -12 -15 Power (Watts) 2.5 -18 -21 -24 2W 2.0 1.5 1.2 W -27 Frequency [MHz] 8010 7510 7010 6510 6010 5510 5010 4510 4010 3510 3010 2510 2010 0.5 1510 -36 1010 1.0 510 -30 -33 10 [dB] 3510 3010 2510 2010 1510 10 8010 7510 7010 6510 6010 5510 5010 4510 4010 3510 3010 2510 2010 1510 1010 10 510 1010 -3.6 -36 510 [dB] -9 0.0 0 20 40 60 80 100 120 140 160 180 Mounting Interface Temperature (°C) 2 200 PD6080J5050S2HF Rev E Wide Band Performance: 5950 MHz. to 8010 MHz. Insertion Loss Return Loss - Input 0 0.0 -3 -6 -0.4 -0.7 -1.1 -1.4 [dB] -18 -21 -24 -1.8 -2.2 -2.5 -27 -2.9 -30 -33 -3.2 20 15 1 10 0.5 5 Frequency [MHz] 7900 7750 7600 7450 7300 Frequency [MHz] Isolation 0 -3 -6 -18 -21 -24 -27 -30 -33 7900 7750 7600 7450 7300 7150 7000 6850 6700 6550 6400 6250 6100 -36 5950 [dB] -9 -12 -15 Frequency [MHz] 3 7900 7750 7600 7450 7300 7150 7000 6850 6700 6550 7900 7750 7600 7450 7300 7150 7000 6850 6700 -20 6550 -15 -2 6400 -10 6250 -1 -1.5 6400 -5 6250 0 -0.5 6100 0 5950 [Deg] 2 1.5 6100 7150 Phase Balance Amplitude Balance 5950 7000 Frequency [MHz] Frequency [MHz] [dB] 6850 6700 6550 6400 5950 7900 7750 7600 7450 7300 7150 7000 6850 6700 6550 6400 6250 6100 5950 6250 -3.6 -36 6100 [dB] -9 -12 -15 PD6080J5050S2HF Rev E Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD6080J5050S2HF is a Wilkinson power divider, an external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability. Pad Footprint w/ 0603 Resistor Location Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) 3x Transmission lines Solder Resist 3x Plated thru holes to ground 6x .33 .04 6x .41 4x .25 .66 R1 4 PD6080J5050S2HF Rev E Packaging and Ordering Information: Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Contact us: rf&s_support@ttm.com 5