X3C09P2-03S

X3C09P2-03S Rev H Hybrid Coupler 3 dB, 90° Description: The X3C09P2-03S is a low profile, high performance 3dB hybrid coupler in a new easy to use, manufacturing friendly surface mount package. It is designed for AMPS, GSM, WCDMA & LTE band applications. The X3C09P2-03S is designed particularly for balanced power and low noise amplifiers, plus signal distribution and other applications where low insertion loss and tight amplitude and phase balance is required. It can be used in high power applications up to 187 watts. Parts have been subjected to rigorous qualification testing and they are manufactured using materials with coefficients of thermal expansion (CTE) compatible with common substrates such as FR4, G-10, RF-35, RO4003 and polyimide. Produced with 6 of 6 RoHS compliant tin immersion finish Features: • 800-1000 MHz • AMPS, GSM, WCDMA & LTE • High Power • Very Low Loss • Tight Amplitude Balance • High Isolation • Production Friendly • Tape and Reel • Lead-Free Outline Drawing: Detailed Electrical Specifications: Frequency Isolation Insertion Loss VSWR Amplitude Balance MHz dB Min dB Max Max : 1 dB Max 800-1000 869-894 925-960 23 25 25 0.20 0.12 0.12 ± 0.22 ± 0.14 ± 0.14 Phase Power ΘJC 1.15 1.12 1.12 Operating Temp. Degrees Avg. CW Watts ºC/Watt 90 ± 4.0 187 @ 95 ºC 15 90 ± 2.0 187 @ 95 ºC 15 90 ± 2.0 187 @ 95 ºC 15 ºC -55 to +150 -55 to +150 -55 to +150 **Specification based on performance of unit properly installed on TTM test board with small signal applied. Specifications subject to change without notice. Refer to parameter definitions for details. 1 X3C09P2-03S Rev H Hybrid Coupler Pin Configuration The X3C09P2-03S has an orientation marker to denote Pin 1. Once port one has been identified the other ports are known automatically. Please see the chart below for clarification: Configuration Splitter Splitter Splitter Splitter *Combiner *Combiner *Combiner *Combiner Pin 1 Input Isolated Pin 2 Isolated Input -3dB ∠θ – 90 -3dB ∠θ -3dB ∠θ -3dB ∠θ – 90 A ∠ θ – 90 A ∠θ Isolated Output A∠θ A ∠θ – 90 Output Isolated Pin 3 -3dB ∠θ – 90 -3dB ∠θ Input Isolated Pin 4 -3dB ∠θ -3dB ∠θ – 90 Isolated Input Isolated Output Output Isolated A ∠θ – 90 A ∠θ A ∠θ A ∠θ – 90 *Notes: “A” is the amplitude of the applied signals. When two quadrature signals with equal amplitudes are applied to the coupler as described in the table, they will combine at the output port. If the amplitudes are not equal, some of the applied energy will be directed to the isolated port. The actual phase, ∠θ, or amplitude at a given frequency for all ports, can be seen in our de-embedded sparameters, that can be downloaded at www.TTM.com. Peak Power Handling High-Pot testing of these couplers during the qualification procedure resulted in a minimum breakdown voltage of 1.46Kv (minimum recorded value). This voltage level corresponds to a breakdown resistance capable of handling at least 12dB peaks over average power levels, for very short durations. The breakdown location consistently occurred across the air interface at the coupler contact pads (see illustration below). The breakdown levels at these points will be affected by any contamination in the gap area around these pads. These areas must be kept clean for optimum performance. It is recommended that the user test for voltage breakdown under the maximum operating conditions and over worst case modulation induced power peaking. This evaluation should also include extreme environmental conditions (such as high humidity). 2 X3C09P2-03S Rev H Insertion Loss and Power Derating Curves X3C09P2-03 Power Derating Curve Typical Insertion Loss Derating Curve for X3C09P2-03 350 0 typical insertion loss (f=894Mhz) typical insertion loss (f=960Mhz) typical insertion loss (f=1000Mhz) -0.02 -0.04 300 250 Power (Watts) Insertion Loss (dB) -0.06 -0.08 -0.1 -0.12 200 187 150 100 -0.14 50 -0.16 -0.18 -100 -50 0 50 100 150 200 o Temperature of the Part ( C) 0 0 50 95 100 150 200 o Mounting Interface Temperature ( C) Insertion Loss Derating: Power Derating: The insertion loss, at a given frequency, of a group of couplers is measured at 25°C and then averaged. The measurements are performed under small signal conditions (i.e. using a Vector Network Analyzer). The process is repeated at 85°C and 150°C. A best-fit line for the measured data is computed and then plotted from -55°C to 150°C. The power handling and corresponding power derating plots are a function of the thermal resistance, mounting surface temperature (base plate temperature), maximum continuous operating temperature of the coupler, and the thermal insertion loss. The thermal insertion loss is defined in the Power Handling section of the data sheet. As the mounting interface temperature approaches the maximum continuous operating temperature, the power handling decreases to zero. If mounting temperature is greater than 95°C, xinger coupler will perform reliably as long as the input power is derated to the curve above. 3 X3C09P2-03S Rev H Typical Performance: (-55°C, 25°C, 95°C, 125°C): 800-1000 MHz 4 X3C09P2-03S Rev H 5 X3C09P2-03S Rev H Definition of Measured Specifications Parameter Definition VSWR (Voltage Standing Wave Ratio) The impedance match of the coupler to a 50Ω system. A VSWR of 1:1 is optimal. Return Loss Insertion Loss Isolation Phase Balance Amplitude Balance The impedance match of the coupler to a 50Ω system. Return Loss is an alternate means to express VSWR. The input power divided by the sum of the power at the two output ports. The input power divided by the power at the isolated port. The difference in phase angle between the two output ports. The power at each output divided by the average power of the two outputs. Mathematical Representation 𝑉𝑉𝑚𝑚𝑚𝑚𝑚𝑚 𝑉𝑉𝑉𝑉𝑉𝑉𝑉𝑉 = 𝑉𝑉𝑚𝑚𝑚𝑚𝑚𝑚 Vmax = voltage maxima of a standing wave Vmin = voltage minima of a standing wave 𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅 𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿(𝑑𝑑𝑑𝑑) = 20𝑙𝑙𝑙𝑙𝑙𝑙 𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼 𝐿𝐿𝐿𝐿𝐿𝐿𝐿𝐿(𝑑𝑑𝑑𝑑) = 10𝑙𝑙𝑙𝑙𝑙𝑙 𝑉𝑉𝑉𝑉𝑉𝑉𝑉𝑉 + 1 𝑉𝑉𝑉𝑉𝑉𝑉𝑉𝑉 − 1 𝑃𝑃𝑐𝑐𝑐𝑐𝑐𝑐 𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼𝐼(𝑑𝑑𝑑𝑑) = 10𝑙𝑙𝑙𝑙𝑙𝑙 𝑃𝑃𝑖𝑖𝑖𝑖 + 𝑃𝑃𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑𝑑 𝑃𝑃𝑖𝑖𝑖𝑖 𝑃𝑃𝑖𝑖𝑖𝑖𝑖𝑖 Phase at coupled port – Phase at direct port 10log Pcpl (Pcpl +Pdirect )⁄2 and 10log Pdirect (Pcpl +Pdirect )⁄2 6 X3C09P2-03S Rev H Packaging and Ordering Information Parts are available in reels. Packaging follows EIA 481-2 for reels. Parts are oriented in tape and reel as shown below. Minimum order quantities are 2000 per reel. .157 [4.00] .012 [0.30] .217 [5.50] TYP Ø.059 [Ø1.50] .315 [8.00] .079 [2.00] .217 [5.50] .472 [12.00] RR .264 [6.70] .069 [1.75] MODEL NO CC .079 [2.00] Dimensions are in Inches [Millimeters] Direction Of Part Feed (Unloading) Contact us: rf&s_support@ttm.com 7