APA4558JC-TU

APA4558 Dual Operational Amplifier Features •!!Power Supply Range: - Signal Supply : 3V to 20V - Dual Supply : ± 1.5V to ± 10V General Description The APA4558 consists of two independent , high gain , internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply up to 20 volts . Operation from dual power supplies is also possible and the power supply current drain is essentially independent of the magnitude of the power supply voltage . Application areas include transducer amplifiers , DC gain blocks and all the conventional OP amplifier circuits which can be more easily implemented in single power supply systems . ( For example , the APA4558 can be directly operated from the standard +5V power supply voltage which is normally used in digital systems . ) • • • • • Large DC Voltage Gain : 100dB Large Output Swing : 0V ~ VDD- 1.5V Bandwidth(unity gain) : 2MHz Internally Frequency Compensated for Unity Gain Low Input Offset Voltage : 1mV Applications •!!Amplifiers •!!Filters •!!Analog Circuit Ordering Information )2)"##& H a n d lin g C o d e T em p. R ange P ackage C ode P ackage C ode J : P D IP K : S O P -8 O : T S S O P -8 Tem p. R ange C : 0 to 7 0 ° C H a n d lin g C o d e TU : Tube TR : Tape & R eel Block Diagram Output A Inverting Input A Non-inverting Input A V,,1 2 3 4 8 V,,+ Output B Inverting Input B Non-inverting Input B -+ +B A 7 6 5 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 1 www.anpec.com.tw APA4558 Absolute Maximum Ratings TA= 25°C Symbol VDD V ID VI PD TA T STG Supply Voltage Differential Input Voltage Input Voltage Power Dissipation Operating Free-air Temperature Range Storage Temperature Range Parameter Rating 20 20 -0.3V to +20V 500 0 to 70 -40 to +150 Unit V V V mW °C °C Electrical Characteristics Symbol V IO IIO IBIAS RIN AV VOM1 VOM2 Parameter Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Large Signal Voltage Gain Maximum Output Voltage Swing 1 VDD=±10V, TA= 25°C APA4558 Min. Typ. 1 5 25 0.3 RL≥2kΩ, VO=±10V RL≥10kΩ RL≥ 2kΩ 86 ±9 ± 8.5 ±9 RS ≤ 10kΩ RS ≤ 10kΩ, VP-P=100mV, fIN=100HZ RIAA, RS =1kΩ ,30kHz, LPF 5 100 ± 9.5 ± 9.0 ± 9.5 90 60 65 3.7 1.4 650 2 6 Max. 6 200 500 Test Conditions RS ≤ 10kΩ Unit mV nA nA MΩ dB V V V dB dB mA µVrms mV/µs MHz Maximum Output Voltage Swing 2 Input Common-Mode Voltage VICM Range CMRR Common-Mode Rejection Ratio SVRR ICC VNI SR GBWP Supply Voltage Rejection Ratio Operating Current Equivalent Input Noise Voltage Slew Rate Gain Bandwidth Product Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 2 www.anpec.com.tw APA4558 Typical Characteristics Open Loop Voltage Gain vs Frequency 120 Maximum Output Voltage Swing vs Frequency 20 Maximum Output Voltage Swing -V Open Loop Voltage Gain - dB 100 80 60 40 20 0 10 18 16 14 12 10 8 6 4 2 0 1 10 100 1k 10k 100k 1M TA= 25°C VDD= ±10V RL=2kΩ TA= 25°C VDD= ±10V RL=2kΩ 100 1k 10k 100k 1M 5M Figure 1 : Frequency (Hz) Figure 2 : Frequency (Hz) Maximum Output Voltage Swing vs Load Resistance Maximum Output Voltage Swing - V 20 18 16 14 12 10 Operating Current vs Temperature 10 9 TA= 25°C Operating Current - mA VDD= ±10V VDD= ±10V 8 7 6 5 4 3 2 1 0 -50 -25 0 25 50 75 100 0.1 0.2 0.5 1 2 5 10 Figure 3 : Load Resistance - kΩ Figure 4 : Temperature - °C Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 3 www.anpec.com.tw APA4558 Typical Characteristics Cont. Maximum Output Voltage Swing vs Temperature Input Offset Voltage vs Temperature 2 1.5 Maximum Output Voltage Swing - V 15 10 5 0 -5 -10 VDD= Input Offset Voltage - mV 1 0.5 0 -0.5 -1 -1.5 -2 -50 -25 0 25 50 75 100 VDD= ±10V RL=10kΩ -15 -50 -25 0 25 50 75 100 Figure 5 : Temperature - °C Figure 6 : Temperature - °C Input Bias Current vs Temperature Maximum Output Voltage Swing - V 100 90 Maximum Output Voltage Swing vs Operating Voltage 10 8 6 4 2 0 -2 -4 -6 -8 -10 ± 2 ± 3 ± 4 ± 5 ± 6 ± 7 ± 8 ± 9 ± 10 VDD= ±10V TA= 25°C RL=2kΩ Input Bias Current - nA 80 70 60 50 40 30 20 10 0 -50 -25 0 25 50 75 100 Figure 7 : Temperature - °C Figure 8 : Operating Voltage - V Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 4 www.anpec.com.tw APA4558 Typical Characteristics Cont. Operating Current vs Operating Voltage  TA= 25°C ' Operating Current -mA & % $ # " !    ±  ± ± ! ± " ± # ± $ ± % ± & ± ' ±  Voltage Follower pulse Response Input Voltage - V Output Voltage - V 7.5 5 2.5 0 7.5 5 2.5 0 0 20 40 60 80 100 Figure 8 : Operating Voltage - V Figure 9 : Time − µs Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 5 www.anpec.com.tw APA4558 Packaging Information PDIP-8 pin ( Reference JEDEC Registration MS-001) D E1 1 E A L e2 e1 e3 A1 A2 1 E3 Dim A A1 A2 D e1 e2 e3 E E1 E3 L φ1 Min. 0.38 2.92 9.02 0.36 1.14 6.10 2.92 0° Millimeters Max. 5.33 3.68 10.16 0.56 1.78 7.11 10.92 3.81 15° Min. 0.015 0.115 0.355 0.014 0.045 0.240 0.115 0° Inches Max. 0.210 0.145 0.400 0.022 0.070 0.280 0.430 0.150 15° 2.54BSC 7.62 BSC 0.100BSC 0.300 BSC Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 6 www.anpec.com.tw APA4558 Package Information SOP- 8 pin ( Reference JEDEC Registration MS-012) 0.015X45° E H e e1 D e2 A1 A 1 L 0.004max. Dim A A1 D E H L e1 e2 φ1 Min. 1.35 0.10 4.80 3.80 5.80 0.40 0.33 Millimeters 1.27BSC 8° Max. 1.75 0.25 5.00 4.00 6.20 1.27 0.51 Min. 0.053 0.004 0.189 0.150 0.228 0.016 0.013 Inches 0.50BSC 8° Max. 0.069 0.010 0.197 0.157 0.244 0.050 0.020 Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 7 www.anpec.com.tw APA4558 TSSOP e 87 2x E/2 E1 E S ( 2) GAUGE PLANE 12 e/2 D 0.25 A2 A ( 3) L (L1) 1 b A1 Dim A A1 A2 b D e E E1 L L1 R R1 S φ1 φ2 φ3 Min. 0.00 0.80 0.19 2.9 4.30 0.45 0.09 0.09 0.2 0° Millimeters 0.65 BSC 6.40 BSC 1.0 REF Max. 1.2 0.15 1.05 0.30 3.1 4.50 0.75 Min. 0.000 0.031 0.007 0.114 0.169 0.018 0.004 0.004 0.008 0° Inches 0.026 BSC 0.252 BSC 0.039REF Max. 0.047 0.006 0.041 0.012 0.122 0.177 0.030 12° REF 12° REF 8° 12° REF 12° REF 8° Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 8 www.anpec.com.tw APA4558 Physical Specifications Terminal Material Lead Solderability Packaging Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. 2500 devices per reel Reflow Condition (IR/Convection or VPR Reflow) Reference JEDEC Standard J-STD-020A APRIL 1999 temperature Peak temperature 183°C Pre-heat temperature Time Classification Reflow Profiles Convection or IR/ Convection Average ramp-up rate(183°C to Peak) 3°C/second max. 120 seconds max Preheat temperature 125 ± 25°C) 60 – 150 seconds Temperature maintained above 183°C Time within 5°C of actual peak temperature 10 –20 seconds Peak temperature range 220 +5/-0°C or 235 +5/-0°C Ramp-down rate 6 °C /second max. 6 minutes max. Time 25°C to peak temperature VPR 10 °C /second max. 60 seconds 215-219°C or 235 +5/-0°C 10 °C /second max. Package Reflow Conditions pkg. thickness ≥ 2.5mm and all bgas Convection 220 +5/-0 °C VPR 215-219 °C IR/Convection 220 +5/-0 °C pkg. thickness < 2.5mm and pkg. volume ≥ 350 mm³ pkg. thickness < 2.5mm and pkg. volume < 350mm³ Convection 235 +5/-0 °C VPR 235 +5/-0 °C IR/Convection 235 +5/-0 °C www.anpec.com.tw Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 9 APA4558 Reliability test program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C , 5 SEC 1000 Hrs Bias @ 125 °C 168 Hrs, 100 % RH , 121°C -65°C ~ 150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms , IJH > 100mA Carrier Tape & Reel Dimensions E Po P P1 D t F W Bo Ao D1 Ko T2 J C A B T1 A p p lic a tio n S O P -8 W P E 1 2 + 0 .3 8 ± 0 .1 1 .7 5 ± 0 .1 - 0 .1 1 2 .4 + 1 2 + 0 .3 TSSO P- 8 2 + 0 .5 3 3 0 ± 1 6 2 ± 1 .5 2 ± 0 .2 8 .0 ± 0 .1 1 .7 5 ± 0 .1 0 .2 - 0 .1 A p p lic a tio n F D Po P1 Ao Bo Ko t 0 .3 ± 0 .0 1 S O P -8 5 .5 ± 0 .1 1 .5 5 ± 0 .1 1 .5 + 0 .2 5 4 .0 ± 0 .1 2 .0 ± 0 .1 6 .4 ± 0 .1 5 .2 ± 0 .1 2 .1 ± 0 .1 3 0 .3 TSSO P- 8 5 .5 ± 0 . 1 .5 + 0 .1 1 .5 + 0 .1 4 .0 ± 0 .1 2 .0 ± 0 .1 7 .0 ± 0 .1 3 .6 ± 0 .3 1 .6 ± 0 .1 ± 0 .0 1 3 (m m ) A 330±1 B 6 2 ± 1 .5 C 1 2 .7 5 + 0 .1 5 1 2 .7 5 ± 0 .1 5 D1 J 2 + 0 .5 T1 1 2 .4 + 0 .2 T2 2 ± 0 .2 Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 10 www.anpec.com.tw APA4558 Cover Tape Dimensions Carrier Width Cover Tape Width 12 9.3 (mm) Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright  ANPEC Electronics Corp. Rev. A.5 - Nov., 2001 11 www.anpec.com.tw