APA7063KI-TR

APA7063 Stereo 1.5W Audio Power Amplifier with DC Volume Control Features • • • • • • • • • • • • • Operating Voltage: 3.3V to 5V DC Volume Control Interface, 0dB to –105dB Depop Circuitry Integrated Thermal shutdown protection circuitry High supply voltage ripple rejection Low Supply Current, IDD = 13mA at Stereo BTL Low Shutdown Current, IDD = 0.7µA Bridge-Tied Load (BTL) or Single-Ended-(SE) Modes Operation Output Power at 1% THD+N, VDD=5V -1.2 W/Ch (typ) into an 8Ω Load Output Power at 10% THD+N, VDD=5V -1.5 W/Ch (typ) into an 8Ω Load Low Crossover Distortion Low Quiescent Current Bridge-tied or Stereo(Single-ended) Configurations General Description The APA7063 is a monolithic integrated circuit that provides DC volume control, and a stereo bridged audio power amplifiers capable of producing 1.5W(1.2W) into 8Ω with less than 10%(1.0%) THD+N. APA7063 provides a volume control pin DC_Vol determines the attenuation of output of the amplifiers. The attenuator range is from 0dB (DC_Vol=0.7VDD) to –105dB (DC_Vol=0V) with 32 steps. Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in the APA7063, that reduces pops and clicks noise during power up and when using the shutdown modes and protects the chip from being destroyed by over temperature failure. To simplify the audio system design applications, the APA7063 combines a stereo bridge-tied loads (BTL) mode for speaker drive and a stereo single-end (SE) mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal. The APA7063 also features a shutdown function which keeps the supply current only 0.7µA (typ). Applications • Portable and Desktop Computers • Multimedia Monitors • Portable Radios, PDAs, and Portable TVs Pin Description SHUTDOWN VCC DC Vol Vo1 Vin1 Vin2 Vo2 GND 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 + OUT1 VCC - OUT1 Bypass SE/BTL - OUT2 VCC + OUT2 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 1 www.anpec.com.tw APA7063 Ordering and Marking Information APA7063 H a n d lin g C o d e Tem p. Range P ackag e C ode Package Code J : P D IP - 1 6 Tem p. Range I : - 4 0 to 8 5 ° C H a n d lin g C o d e TU : Tube K : SO P - 16 TR : Tape & Reel APA7063 J : APA7063 XXXXX X X X X X - D a te C o d e APA7063 K : APA7063 XXXXX X X X X X - D a te C o d e Block Diagram SE/BTL 10KΩ 10KΩ Vo1 Vin1 Bias Vin2 + Volume Control 32 steps Vo2 Shutdown VCC GND Bypass Power Management Click and Pop Suppression Circuitry 20KΩ + + - OUT2 10KΩ 10KΩ Absolute Maximum Ratings (Over operating free-air temperature range unless otherwise noted.) Symbol VDD TA TJ TSTG TS VESD Parameter Supply Voltage Operating Ambient Temperature Range Maximum Junction Temperature Storage Temperature Range Soldering Temperature,10 seconds Electrostatic Discharge 2 Rating 6 -40 to 85 150 -65 to +150 260 -2000 to 2000*1 Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 + - + 20KΩ 20KΩ + 20KΩ + OUT1 - OUT1 + OUT2 Unit V °C °C °C °C V www.anpec.com.tw APA7063 Electical Characteristics Electrical Characteristics for Entire IC The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25°C Symbol VDD IDD ISD VIH VIL Parameter Supply Voltage Quiescent Power Supply Current Shutdown Current SE/BTL High Input Voltage SE/BTL Low Input Voltage Test Conditions Min. 3.3 VIN=0V, IO =0A VPIN 2= VDD 4 APA7063 Typ. Max. 5.5 13 25 0.7 2.0 0.8 Unit V mA µA V V Electrical Characteristics for Volume Attenuators The following specifications apply for VDD= 5V. Limits apply for TA= 25°C Symbol CRANGE Parameter Attenuator Range Test Conditions Gain with VpIN 3=5V Attenuation with VpIN 3=0V APA7063 Min. Typ. Max. ±0.5 -100 -105 Unit dB Electrical Characteristics for BTL Mode Operation The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25°C Symbol VOS PO Parameter Output Offset Voltage Output Power Test Conditions THD+N VIN=0V THD=1%, f=1kHz RL=8Ω THD=10%, f=1kHz RL=8Ω Total Harmonic Distortion + Noise AVD =2, 20Hz