APC558JC-TU

APC558 Dual Operational Amplifier Features • Power Supply Range : General Description The APC558 consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply up to 20 volts. Operation from dual power supplies is also possible and the power supply current drain is essentially independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, DC gain blocks and all the conventional OP amplifier circuits which can be more easily implemented in single power supply systems. (For example, the APC558 can be directly operated from the standard +5V power supply voltage which is normally used in digital systems.) • Signal Supply : 3V to 20V • Dual Supply : ± 1.5V to ± 10V • • • • • Large DC Voltage Gain : 100dB Large Output Swing : 0V ~ VDD- 1.5V Bandwidth(unity gain) : 2MHz Internally Frequency Compensated for Unity Gain Low Input Offset Voltage : 1mV Applications • • • Amplifiers Filters Analog Circuit Ordering and Marking Information A P C 558 Lead F ree C ode H andling C ode T em p. R ange P ack age C ode P ackage C ode J : P D IP K : S O P -8 O : T S S O P -8 T em p. R ange C : 0 to 70 ° C H andling C ode T U : T ube T R : T ape & R eel Lead F ree C ode L : Lead F ree D evice B lank : O riginal D evice XXXXX - D ate C ode A P C 558 J : A P C 558 XXXXX A P C 558 XXXXX A P C 558 K /O : XXXXX - D ate C ode ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 1 www.anpec.com.tw APC558 Block Diagram Output A Inverting Input A Non-inverting Input A VDD1 8 VDD+ Output B Inverting Input B Non-inverting Input B 2 -+ +B A 7 3 6 4 5 Absolute Maximum Ratings Symbol VDD VID VI PD TA TSTG TA= 25°C Rating 20 20 -0.3V to +20V 500 0 to 70 -40 to +150 Unit V V V mW °C °C Parameter Supply Voltage Differential Input Voltage Input Voltage Power Dissipation Operating Free-air Temperature Range Storage Temperature Range Electrical Characteristics Symbol V IO IIO IBIAS RIN AV VOM1 VOM2 VICM Parameter VDD=±10V, TA= 25°C Test Conditions Min. RS ≤ 10kΩ APC558 Typ. Max. 1 3 2 10 25 70 5 100 ± 9.5 ± 9.0 ± 9.5 90 65 3.7 1.4 650 2 6 Unit mV nA nA MΩ dB V V V dB dB mA µVrms mV/µs MHz Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Large Signal Voltage Gain Maximum Output Voltage Swing 1 Maximum Output Voltage Swing 2 Input Common-mode Voltage Range CMRR Common-mode Rejection Ratio SVRR Supply Voltage Rejection Ratio ICC VNI Operating Current Equivalent Input Noise Voltage RL≥2kΩ , VO=±10V RL≥10kΩ R L≥ 2 kΩ 0.3 86 ±9 ± 8.5 ±9 RS ≤ 10kΩ RS ≤ 10kΩ, VP-P =100mV, fIN=100HZ RIAA, RS =1kΩ ,30kHz, LPF 60 SR Slew Rate GBWP Gain Bandwidth Product Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 2 www.anpec.com.tw APC558 Typical Characteristics Open Loop Voltage Gain vs Frequency Maximum Output Voltage Swing -V 120 Maximum Output Voltage Swing vs Frequency 20 18 16 14 12 10 8 6 4 2 0 1 10 100 1k 10k 100k 1M TA= 25°C VDD= ±10V Open Loop Voltage Gain - dB 100 80 60 40 20 0 TA= 25°C VDD= ±10V R L= 2 k Ω R L= 2 k Ω 10 100 1k 10k 100k 1 M 5 M Frequency (Hz) Figure 1 Frequency (Hz) Figure 2 Maximum Output Voltage Swing vs Load Resistance 20 Operating Current vs Temperature 10 Maximum Output Voltage Swing - V TA= 25°C 18 16 14 12 10 9 VDD= ±10V Operating Current - mA VDD= ±10V 8 7 6 5 4 3 2 1 0 -50 0.1 0.2 0.5 1 2 5 10 -25 0 25 50 75 100 Load Resistance - kΩ Figure 3 Temperature - °C Figure 4 Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 3 www.anpec.com.tw APC558 Typical Characteristics Cont. Maximum Output Voltage Swing vs Temperature Maximum Output Voltage Swing - V 15 10 5 0 -5 -10 -15 -50 2 1.5 Input Offset Voltage vs Temperature VDD= ±10V Input Offset Voltage - mV 1 0.5 0 -0.5 -1 -1.5 -2 -50 -25 0 25 50 75 100 VDD= ±10V RL=10kΩ -25 0 25 50 75 100 Temperature - °C Figure 5 Temperature - °C Figure 6 Input Bias Current vs Temperature 100 90 10 8 6 4 2 0 -2 -4 -6 -8 - 10 Maximum Output Voltage Swing vs Operating Voltage Maximum Output Voltage Swing - V VDD= ±10V TA= 25°C Input Bias Current - nA 80 70 60 50 40 30 20 10 0 -50 R L= 2 kΩ -25 0 25 50 75 100 ± 2 ± 3 ± 4 ± 5 ± 6 ± 7 ± 8 ± 9 ± 10 Temperature - °C Figure 7 Operating Voltage - V Figure 8 Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 4 www.anpec.com.tw APC558 Typical Characteristics Cont. Operating Current vs Operating Voltage Input Voltage - V Output Voltage - V 10 9 Voltage Follower pulse Response 7.5 5 2.5 0 7.5 5 2.5 0 0 20 40 60 80 100 TA= 25°C Operating Current -mA 8 7 6 5 4 3 2 1 0 0 ± 1 ± 2 ± 3 ± 4 ± 5 ± 6 ± 7 ± 8 ± 9 ± 10 Operating Voltage - V Figure 8 Time − µs Figure 9 Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 5 www.anpec.com.tw APC558 Package Information PDIP-8 pin ( Reference JEDEC Registration MS-001) D E1 1 E A L e2 e1 e3 A1 A2 1 E3 Dim Min. A A1 A2 D e1 e2 e3 E E1 E3 L φ1 0.38 2.92 9.02 Millimeters Max. 5.33 3.68 10.16 2.54BSC 0.36 1.14 7.62 BSC 6.10 2.92 15° 7.11 10.92 3.81 0.240 0.115 0.56 1.78 0.014 0.045 Min. 0.015 0.115 0.355 Inches Max. 0.210 0.145 0.400 0.100BSC 0.022 0.070 0.300 BSC 0.280 0.430 0.150 15° Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 6 www.anpec.com.tw APC558 Package Information SOP- 8 pin ( Reference JEDEC Registration MS-012) 0.015X45 ° E H e e1 D e2 A1 A 1 L 0.004max. Dim A A1 D E H L e1 e2 φ1 Min. 1.35 0.10 4.80 3.80 5.80 0.40 0.33 Millimeters Max. 1.75 0.25 5.00 4.00 6.20 1.27 0.51 1.27BSC 8° Min. 0.053 0.004 0.189 0.150 0.228 0.016 0.013 Inches Max. 0.069 0.010 0.197 0.157 0.244 0.050 0.020 0.50BSC 8° Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 7 www.anpec.com.tw APC558 Package Information TSSOP-8 e 87 2x E/2 E1 E S ( 2) GAUGE PLANE 1 2 e/2 D A2 A b A1 0.25 L (L1) ( 3) 1 Dim A A1 A2 b D e E E1 L L1 R R1 S φ1 φ2 φ3 Millimeters Min. 0.00 0.80 0.19 2.9 0.65 BSC 6.40 BSC 4.30 0.45 1.0 REF 0.09 0.09 0.2 0° 0.004 0.004 0.008 0° 4.50 0.75 0.169 0.018 Max. 1.2 0.15 1.05 0.30 3.1 Min. 0.000 0.031 0.007 0.114 Inches Max. 0.047 0.006 0.041 0.012 0.122 0.026 BSC 0.252 BSC 0.177 0.030 0.039REF 12° REF 12° REF 8° 12° REF 12° REF 8° Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 8 www.anpec.com.tw APC558 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition TP (IR/Convection or VPR Reflow) tp C ritical Zone T L to T P R am p-up T e m p e ra tu re TL T sm ax tL T sm in R am p-down ts Preheat 25 t 25 °C to Peak T im e Classificatin Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Large Body Small Body Pb-Free Assembly Large Body Small Body 3°C/second max. 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds 245 +0/-5°C 250 +0/-5°C 10-30 seconds 20-40 seconds 6°C/second max. 8 minutes max. www.anpec.com.tw Average ramp-up rate 3°C/second max. (TL to TP) Preheat - Temperature Min (Tsmin) 100°C - Temperature Mix (Tsmax) 150°C - Time (min to max)(ts) 60-120 seconds Tsmax to TL - Ramp-up Rate Tsmax to TL - Temperature(TL) 183°C - Time (tL) 60-150 seconds Peak Temperature(Tp) 225 +0/-5°C 240 +0/-5°C Time within 5°C of actual Peak 10-30 seconds 10-30 seconds Temperature(tp) Ramp-down Rate 6°C/second max. 6 minutes max. Time 25°C to Peak Temperature Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 9 Note: All temperatures refer to topside of the package. Measured on the body surface. APC558 Reliability Test Program Test item S OLDERABILITY H OLT P CT T ST E SD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245 °C, 5 SEC 1000 Hrs Bias @125°C 168 Hrs, 100% RH, 121°C -65 °C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA Carrier Tape & Reel Dimensions t P P1 D Po E F W Bo Ao Ko D1 T2 J C A B T1 Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 10 www.anpec.com.tw APC558 Carrier Tape & Reel Dimensions Application A 3 30 ± 1 B C 62 ± 1 .5 12.75 +0.15 J 2 + 0.5 Po 4.0 ± 0 .1 J 2 + 0.5 Po 4.0 ± 0 .1 T1 12.4 +0.2 P1 2.0 ± 0 .1 T1 12.4 ± 0 .2 P1 2.0 ± 0 .1 T2 2 ± 0 .2 Ao 6.4 ± 0 .1 T2 2 ± 0 .2 Ao 7.0 ± 0 .1 W 12 + 0.3 - 0.1 Bo 5.2 ± 0 .1 W 12 ± 0 . 3 Bo 3.6 ± 0 .3 P 8 ± 0 .1 E 1.75 ± 0 .1 S OP-8 F D D1 5 .5 ± 0 .1 1.55 ± +0.1 1.55+0.25 A 3 30 ± 1 B C Ko t 2.1 ± 0 .1 0.3 ± 0.013 P 8 ± 0 .1 Ko 1.6 ± 0 .1 E 1.75 ± 0.1 t .3 ± 0.013 A pplication 6 2 +1.5 12.75+ 0.15 D D1 1.5 + 0.1 T SSOP-8 F 5 .5 ± 0 . 1 1.5 + 0.1 ( mm) Cover Tape Dimensions Application SOP- 8 TSSOP- 8 Carrier Width 12 12 Cover Tape Width 9.3 9.3 Devices Per Reel 2500 2500 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright  ANPEC Electronics Corp. Rev. A.4 - July., 2002 11 www.anpec.com.tw