APL1086-25FC-TU

APL1086 1.5A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V Features • • • • • • • • • • Guaranteed Output Voltage Accuracy within 2% Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents Load Regulation : 0.1% Typ. Line Regulation : 0.03% Typ. Low Dropout Voltage : 1.3V Typ. at IOUT =1.5A Current Limit : 1.5A Min. at TJ=125°C On-Chip Thermal Limiting : 150 °C Typ. Adjustable Output : 1.25~10.7V Standard 3-pin SOT-223, TO-252 , TO-220 and TO-263 Power Packages. General Description The APL1086 is a low dropout three-terminal adjustable regulators with 1.5A output current capability. In order to obtain lower dropout voltage and faster transient response, which is critical for low voltage applications , the APL1086 has been optimized. The device is available in an adjustable version and fixed output voltages of 1.8V, 2.5V,2.85V and 3.3V, the output available voltage range is from 1.25~10. 7V with an input supply below 12V. Dropout voltage is guaranteed at a maximum of 1.45V at 1.5A. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload that would create excessive junction temperatures. The APL1086 is available in the industry standard 3pin SOT-223, TO-252, TO-220 or TO-263 power packages. Applications • • • • Active SCSI Terminators Low Voltage Logic Supplies Battery-Powered Circuitry Post Regulator for Switching Power Supply 1 2 3 Pin Description TAB IS VOUT TAB IS VOUT 1 2 3 ADJ/GND OUT IN ADJ/GND OUT IN Front View for SOT-223 Front View for TO-252 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 1 www.anpec.com.tw APL1086 Pin Description 3 2 1 VIN VOUT ADJ TA B is V O U T 3 2 1 V IN V OUT AD J Front View for TO-220 Front View for TO-263 Ordering and Marking Information APL1086H a n d lin g C o d e Tem p. R ange Package Code V o lta g e C o d e Package Code F : T O -2 2 0 G : T O -2 6 3 U : T O -2 5 2 V : S O T -2 2 3 Tem p. R ange C : 0 to 7 0 ° C H a n d lin g C o d e TU : Tube TR : Tape & R eel V o lta g e C o d e 1 8 : 1 .8 V 2 5 : 2 .5 V 2 8 5 : 2 .8 5 V B la n k : A d ju s ta b le V e rs io n AP L1086 XXXXX 3 3 : 3 .3 V A P L 1 0 8 6 F /G /U : AP L1086 XXXXX 18 AP L1086 XXXXX 25 AP L1086 XXXXX 285 AP L1086 XXXXX 33 AP L1086 XXXXX XXXXX - D a te C o d e AP L1086 V : X X X X X - D a te C o d e A P L 1 0 8 6 -1 8 F /G /U : XXXXX - D a te C o d e AP L1086- 18V : AP L1086 XX XXX 18 X X X X X - D a te C o d e A P L 1 0 8 6 -2 5 F /G /U : XXXXX - D a te C o d e AP L1086- 25V : AP L1086 XX XXX 25 X X X X X - D a te C o d e A P L 1 0 8 6 -2 8 5 F /G /U : XXXXX - D a te C o d e AP L1086- 285V : AP L1086 XX XXX 285 X X X X X - D a te C o d e A P L 1 0 8 6 -3 3 F /G /U : XXXXX - D a te C o d e AP L1086- 33V : AP L1086 XX XXX 33 X X X X X - D a te C o d e Absolute Maximum Ratings Symbol VI TJ Parameter Input Voltage Operating Junction Temperature Range Control Section Power Transistor Storage Temperature Range Lead Temperature (Soldering, 10 second) Rating 12 0 to 125 0 to 150 -65 to +150 260 Unit V °C TSTG TL °C °C Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 2 www.anpec.com.tw APL1086 Electrical Characteristics Symbol V REF Parameter Test Conditions APL1086 Min. Typ. Max. 1.225 1.250 1.275 1.782 1.800 1.818 1.764 1.800 1.836 2.475 2.500 2.525 2.450 2.500 2.550 V 2.822 2.850 2.878 2.792 2.850 2.910 3.267 3.300 3.333 3.235 3.300 3.365 Unit V V OUT REG LINE REG LOAD VD ILIMIT IADJ ∆ IADJ 10mA ≤ IOUT ≤1.5A, 1.4V ≤ (V IN -VOUT) ≤ 9.75V, Reference Voltage T J = 0~125 °C Output Voltage APL1086-18 T J = 25°C, IOUT = 0mA, T J = 0~125 °C, 0 ≤ IOUT≤ 1 .5A, 3.5V ≤ V IN≤ 9V, APL1086-25 T J = 25°C, IOUT = 0mA, T J = 0~125 °C, 0 ≤ IOUT≤ 1 .5A, 4V ≤ V IN≤ 9V, APL1086-28 T J = 25°C, IOUT = 0mA, T J = 0~125 °C, 0 ≤ IOUT≤ 1 .5A, 4.25V ≤V IN≤ 9V, APL1086-33 T J = 25°C, IOUT = 0mA, T J = 0~125 °C, 0 ≤ IOUT≤ 1 .5A, 4.75V ≤V IN≤ 9V, Line Regulation T J = 0~125 °C APL1086 IOUT=10mA, 1.5V ≤V IN – V OUT≤ 9V, (note1) APL1086-18 IOUT=0mA, 3.5V ≤ V IN≤ 9V, (note1) APL1086-25 IOUT=0A, 4V ≤ V IN≤ 9V, (note 1) APL1086-28 IOUT=0A, 4.25V ≤V IN ≤ 9V, (note 1) APL1086-33 IOUT=0A, 4.75V ≤V IN ≤ 9 V, (note 1) Load Regulation T J = 0~125 °C APL1086 (V IN -V OUT)=3V, 0≤ IOUT ≤ 1.5A ,(note 1) APL1086-18 V IN=3.5V, 0≤ IOUT ≤ 1.5A ,(note 1) APL1086-25 V IN=4V, 0≤ IOUT ≤ 1.5A ,(note 1) APL1086-28 V IN=4.25V, 0 ≤ IOUT ≤1.5A ,(note 1) APL1086-33 V IN=4.75V, 0 ≤ IOUT ≤1.5A ,(note 1) Dropout Voltage IOUT=1.5A ,T J = 0~125 °C Current Limit (V IN -V OUT)=5V, T J=25 ° C Adjust Pin Current (V IN -V OUT)=3V, IOUT=10mA, T J=0~125 °C 0.03 1 1 1 1 0.1 1 1 1 1 1.3 1500 60 0.2 1.7 60 75 0.01 0.5 0.3 0.2 6 6 6 6 0.4 10 10 10 10 1.45 120 5 % mV % mV V mA µA µA mA dB Adjust Pin Current T J= 0~125°C, 10mA ≤ IOUT ≤ 1.5A, Change 1.4V ≤ (VIN -V OUT) ≤7.75V Minimum Load IO T J=0~125 °C, (V IN -V OUT)=7.75V, (note 3) Current F RIPPLE=120Hz, V RIPPLE =1V P-P, PSRR Ripple Rejection (V IN -V OUT)=3V, T J=0~125 °C Thermal TR T J=25 °C, 30ms Pulse Regulation Temperature TS Stability Long -Term LS T J = 125 ° C,1000Hrs. Stability Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 3 0.02 %/ W % % www.anpec.com.tw APL1086 Electrical Characteristics (Cont.) Symbol VN θ th OT Parameter RMS Output Noise Thermal Resistance Over Temperature Point Quiescent Current APL1086-18 APL1086-25 APL1086-28 APL1086-33 Test Conditions T J=25 °C,10Hz≤ F ≤10kHz, (% of V OUT) Junction to Case, at Tab Junction to ambient APL1086 Min. Typ. Max. 0.003 15 50 150 T J=0~125 °C, V IN≤ 9V V IN≤ 9V V IN≤ 9V V IN≤ 9V 5.5 5.5 5.5 5.5 10 10 10 10 Unit % °C/ W °C mA Note 1: See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are measured at a constant junction temperature by low duty cycle pulse testing. Note 2: Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/ output differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve. Note 3: Minimum load current is defined as the minimum output current required to maintain regulation. Application Circuits 1.25V to 10.7V Adjustable Regulator APL1086 V IN IN ADJ OUT R1 121 Ω + 10µ F Improving Ripple Rejection V OUT 1 V IN 10µ F + APL1086 IN OUT ADJ R1 121 Ω 1% + C1 10µ F V OUT 150 µ F + R2 1k 100µ F C 1* C2 * Needed if device is far from filter capacitors * C1 improves ripple rejection. XC should be approximately equal to R1 at ripple frequency R2 365 Ω 1% VOUT = 1.250V× R1 + R2 R1 5V Regulator with Shutdown APL1086 IN OUT ADJ + TTL 1k 10µ F V IN 5V 121 Ω 1% + 365 Ω 1% 1k 100µ F Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 4 www.anpec.com.tw APL1086 Typical Characteristics Load Transient Response 5 4.5 0.02 Line Transient Response 6 0.15 Output Voltage Deviation (V) Output Current (A) Input Voltage (V) 3.5 3 2.5 2 1.5 1 0.5 0 -100 100 300 500 700 -0.03 900 -0.02 0 0.1 4 CIN=10uF Cout=10uF Tantalum VIN=5V 3 CIN=10uF Cout=10uF Tantalum IOUT=0.1A 0.05 -0.01 2 0 1 -0.05 -20 30 80 130 180 0 Time (µs) Time (µs) Dropout Voltage vs. Output Current 1.35 1.3 1.25 Output Voltage vs. Input Voltage 3.5 3 Output Voltage (V) Dropout Voltage (V) 1.2 1.15 1.1 1.05 1 0.95 0.9 0 0.5 1 1.5 2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6 7 8 9 Output Current (A) Input Voltage (V) Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 5 www.anpec.com.tw Output Voltage Deviation (V) 4 0.01 5 APL1086 Typical Characteristics Cont. Input Current vs. Input Voltage 6 3.4 Current Limit vs. Input Voltage Vout=1.25V 5 2.9 Input Current (mA) 3 2 1 0 0 2 4 6 8 10 Current Limit (A) 4 2.4 1.9 1.4 0.9 0 3 6 9 12 Input Voltage (V) Input Voltage (V) Output Voltage vs. Temperature 3 .4 Output Voltage vs. Temperature 2.6 2.5 2.4 3 .3 Output Voltage (V) 2.3 2.2 2.1 2 1.9 1.8 1.7 1.6 -50 -25 0 25 50 75 100 125 Output Voltage (V) 3 .2 3 .1 3 .0 2 .9 2 .8 2 .7 -5 0 -2 5 0 25 50 75 100 125 Temperature (°C) Temperature (°C) Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 6 www.anpec.com.tw APL1086 Typical Characteristics Cont. A djustable P in C urrent vs. Tem perature Input Current vs. Tem perature 68 8 7 A djustable P in C urrent (µ A ) 64 Input Current (mA) 6 60 5 4 56 3 52 -50 -25 0 25 50 75 100 125 2 -50 -25 0 25 50 75 100 125 Tem perature ( ° C ) Tem perature ( ° C) Current Limit vs. Temperature 2 .9 2 .7  Current Limit (mA) 2 .5 Vin-Vout=5V 2 .3 2 .1 1 .9 1 .7 1 .5 -5 0 -3 0 -1 0 1 0 3 0 5 0 7 0 9 0 10 1 10 3 10 5 Temperature (°C) Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 7 www.anpec.com.tw APL1086 Package Information SOT-223( Reference JEDEC Registration SOT-223) D B1 A c a H E L K e e1 b A1 B Dim A A1 B B1 c D E e e1 H L K α β Min. 1.50 0.02 0.60 2.90 0.28 6.30 3.30 Millimeters Max. 1.80 0.08 0.80 3.10 0.32 6.70 3.70 2.3 BSC 4.6 BSC 6.70 0.91 1.50 0° 7.30 1.10 2.00 10° 0.26 0.04 0.06 0° Min. 0.06 0.02 0.11 0.01 0.25 0.13 Inches Max. 0.07 0.03 0.12 0.01 0.26 0.15 0.09 BSC 0.18 BSC 0.29 0.04 0.08 10° 13° 13° Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 8 www.anpec.com.tw APL1086 Package Informaion TO-252( Reference JEDEC Registration TO-252) E b2 L2 A C1 D H L1 L b e1 D1 C A1 E1 Dim A A1 b b2 C C1 D D1 E E1 e1 H L L1 L2 M illim et er s M in. 2. 1 8 0. 8 9 0. 5 08 5. 2 07 0. 4 6 0. 4 6 5. 3 34 5. 2 R EF 6. 3 5 5. 3 R EF 3. 9 6 9. 3 98 0. 5 1 0. 6 4 0. 8 9 1. 0 2 2. 0 32 9 Inc he s M ax. 2. 3 9 1. 2 7 0. 8 9 5. 4 61 0. 5 8 0. 5 8 6. 2 2 6. 7 3 5. 1 8 10 . 41 M in. 0. 0 86 0. 0 35 0. 0 20 0. 2 05 0. 0 18 0. 0 18 0. 2 10 0. 2 05 R EF 0. 2 50 0. 2 09 R EF 0. 1 56 0. 3 70 0. 0 20 0. 0 25 0. 0 35 0. 0 40 0. 0 80 www.anpec.com.tw M ax. 0. 0 94 0. 0 50 0. 0 35 0. 2 15 0. 0 23 0. 0 23 0. 2 45 0. 2 65 0. 2 04 0. 4 10 Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 APL1086 Package Informaion TO-220 ( Reference JEDEC Registration TO-220) D Q R b E e b1 e1 L1 H1 L A F c J1 Millimeters Dim A b1 b c D e e1 E F H1 J1 L L1 R Q Min. 3.56 1.14 0.51 0.31 14.23 2.29 4.83 9.65 0.51 5.84 2.03 12.7 3.65 3.53 2.54 Max. 4.83 1.78 1.14 1.14 16.51 2.79 5.33 10.67 1.40 6.86 2.92 14.73 6.35 4.09 3.43 Min. 0.140 0.045 0.020 0.012 0.560 0.090 0.190 0.380 0.020 0.230 0.080 0.500 0.143 0.139 0.100 Inches Max. 0.190 0.070 0.045 0.045 0.650 0.110 0.210 0.420 0.055 0.270 0.115 0.580 0.250 0.161 0.135 Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 10 www.anpec.com.tw APL1086 Package Informaion TO-263 ( Reference JEDEC Registration TO-263) E L2 A c2 D L L1 L3 e b2 b c M illimeters Dim A b b2 c c2 D E e L L1 L2 L3 M in. 4.06 0.51 1.14 0.38 TYP. 1.14 8.64 9.66 2.543 BSC. 14.60 2.24 1.20 15.88 2.8 4 2.92 1.78 0.575 0 .090 0.050 1.40 9.65 10.299 0 .0 4 5 0.340 0.380 M ax. 4.83 0.992 1.399 M in. 0.160 0 .0 2 0.045 Inches M ax. 0.190 0 .039 0.055 0.015 TYP. 0 .055 0.380 0.405 0.100 BSC. 0.625 0 .11 0 0.115 0.070 Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 11 www.anpec.com.tw APL1086 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) Reference JEDEC Standard J-STD-020A APRIL 1999 temperature Peak temperature 183°C Pre-heat temperature Time Classification Reflow Profiles Convection or IR/ Convection Average ramp-up rate(183°C to Peak) 3°C/second max. 120 seconds max Preheat temperature 125 ± 25°C) 60 – 150 seconds Temperature maintained above 183°C Time within 5°C of actual peak temperature 10 –20 seconds Peak temperature range 220 +5/-0°C or 235 +5/-0°C Ramp-down rate 6 °C /second max. 6 minutes max. Time 25°C to peak temperature VPR 10 °C /second max. 60 seconds 215-219°C or 235 +5/-0°C 10 °C /second max. Package Reflow Conditions pkg. thickness ≥ 2.5mm and all bgas Convection 220 +5/-0 °C VPR 215-219 °C IR/Convection 220 +5/-0 °C pkg. thickness < 2.5mm and pkg. volume ≥ 350 mm³ pkg. thickness < 2.5mm and pkg. volume < 350mm³ Convection 235 +5/-0 °C VPR 235 +5/-0 °C IR/Convection 235 +5/-0 °C www.anpec.com.tw Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 12 APL1086 Reliability test program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C , 5 SEC 1000 Hrs Bias @ 125 °C 168 Hrs, 100 % RH , 121 °C -65°C ~ 150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms , Itr > 1 00mA Carrier Tape & Reel Dimensions t P P1 D Po E F W Bo Ao Ko D1 T2 J C A B T1 A pp lication A 330 ± 3 B 100 ± 2 D C 13 ± 0 . 5 D1 T1 T2 16.4 + 0.3 2.5 ± 0 .5 2 ± 0 .5 -0.2 Po P1 Ao J W 16+ 0.3 - 0.1 Bo P 8 ± 0 .1 Ko E 1.75 ± 0 .1 t TO-252 F 7.5 ± 0 .1 1.5 +0.1 1.5 ± 0 .25 4.0 ± 0 .1 2.0 ± 0 .1 6.8 ± 0 .1 10.4 ± 0 .1 2.5 ± 0 .1 0.3 ± 0.05 A pp lication A 380 ± 3 TO-263 F B 80 ± 2 D C 13 ± 0 . 5 D1 J 2 ± 0 .5 Po T1 24 ± 4 P1 T2 2 ± 0 .3 Ao W 24 + 0.3 - 0.1 Bo P E 16 ± 0 .1 1.75 ± 0 .1 Ko t 11.5 ± 0 .1 1.5 +0.1 1.5 ± 0 .25 4.0 ± 0 .1 2.0 ± 0 .1 10.8 ± 0 .1 16.1 ± 0 .1 5.2 ± 0 .1 0.35 ± 0.01 3 (mm) Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 13 www.anpec.com.tw APL1086 Reel Dimensions (Cont.) A pp lication A 330 ± 1 SOT-223 F B 62 ± 1.5 D C 12.75 ± 0.15 D1 J 2 ± 0 .6 Po T1 12.4 +0.2 P1 T2 2 ± 0 .2 Ao W 12 ± 0 .3 Bo P 8 ± 0 .1 Ko E 1.75 ± 0 .1 t 5.5 ± 0 .05 1.5+ 0.1 1.5+ 0.1 4.0 ± 0 .1 2.0 ± 0 .05 6.9 ± 0 .1 7.5 ± 0 .1 2.1 ± 0 .1 0.3 ± 0.05 (mm ) Cover Tape Dimensions Application TO- 252 TO- 263 SOT- 223 Carrier Width 16 24 12 Cover Tape Width 13.3 21.3 9.3 Devices Per Reel 2500 1000 2500 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright  ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 14 www.anpec.com.tw