APL1431LABI-TB

APL1431L Low Voltage Adjustable Precision Shunt Regulator Features • • • • • • • • Precise Reference Voltage to 1.24V Guaranteed 0.5% or 1% Reference Voltage Tolerance Sink Current Capability , 60mA to 100mA Quick Turn-on Adjustable Output Voltage , VO = VREF to 20V Low Operational Cathode Current , 60mA Typical 0.1Ω Typical Output Impedance SOT-23-5 Packages General Description The APL1431L is a 3-terminal low voltage adjustable precision reference with specified thermal stability over applicable commercial temperature ranges . Output voltage may be set to any value between VREF (1.24 V) and 20 V with two external resistors (see Figure 2) . When used with an photocoupler , the APL1431L is an ideal voltage reference in isolated feedback circuits for 1.24V to 12V switchingmode power supplies . This device has a typical output impedance of 0.1Ω . Active output circuitry provides a very sharp turn-on characteristic , making the APL1431L excellent replacements for zener diodes in many applications , including on-board regulation and adjustable power supplies . AN O DE RE F Applications • • • Linear Regulators Adjustable Power Supply Switching Power Supply 5 1 2 4 3 NC NC C A T H O DE Symbol REF Anode Cathode Functional Diagram C athode R EF + − V REF Anode ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 1 www.anpec.com.tw APL1431L Ordering and Marking Information APL1431L Lead Free Code Handling Code Temp. Range Package Code Elec. Grade Elec. Grade A : 0.5% Reference Voltage Tolerance B : 1% Reference Voltage Tolerance Package Code B : SOT- 23 - 5 Temp. Range C : 0 to 70 C I : -40 to 85 C Handling Code PB : Plastic Bag TB : Tape & Box TR : Tape & Reel Lead Free Code L : Lead Free Device Blank : Original Device APL1431L B : 1431L Absolute Maximum Ratings Symbol VKA IK IREF θJA TJ TSTG TSOL Cathode Voltage Continuous Cathode Current Reference Current Thermal Resistance from Junction to Ambient in Free Air SOT-23-5 Operating Junction Temperature Range Storage Temperature Range Lead Temperature Range, Ts (Soldering, 10sec) Parameter Rating 20 100 3 357 -40 to 150 -65 to 150 260 Unit V mA mA °C/W °C °C °C Electrical Characteristics Symbol Parameter TA= 25°C ( unless otherwise noted) APL1431L Min. Typ. Max. 1.234 1.240 1.246 1.228 1.240 1.252 1.222 1.240 1.258 1.215 1.240 1.265 5 15 Test Conditions VKA=VREF, IK=10mA TA= 25°C, (Fig. 1) TA= full range (see Note 1), (Fig. 1) APL1431LA APL1431LB APL1431LA APL1431LB Unit VREF Reference Voltage V VDEV ∆VREF /∆VKA IREF VDEF Temp Deviation TA= full range(see Note 1), VKA =VREF , IK =10mA, (Fig. 1) mV Ratio of Change in VREF to Change in Cathode IK=10mA, ∆VKA =16V to VREF (Fig. 2) Voltage Reference Input Current IK=10mA, R1=10kΩ, R2=∞ (Fig. 2) -0.2 0.15 -1.0 0.5 mV/V µA Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 2 www.anpec.com.tw APL1431L Electrical Characteristics Symbol IREF(DEV) IK(off) ZKA IK(MIN) Parameter IREF Temp Deviation TA= 25°C ( unless otherwise noted) APL1431L Min. Typ. Max. 0.05 0.01 0.01 0.1 60 0.3 0.1 0.5 0.3 80 Test Conditions Unit µA µA Ω µA TA= full range(see Note 1), R1=10kΩ, R2=∞ , IK=10mA, (Fig. 2) VK=6V Off-state cathode current VREF=0V, (Fig. 3) VK=16V Dynamic Output VKA =VREF , IK=100µA to 100mA , Impedance fVREF, VO= VKA= VREF× (1+R1/R2) + IREF × R1 V IN IK(OFF) VO Figure 3. Test Circuit for IK(OFF) Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 3 www.anpec.com.tw APL1431L Application Schematic RB V IN VO R1 V REF APL431L R2 0.1 µF GND Precision Voltage Reference V IN RB VO R1 VREF APL431L 0.1 µF R2 Precision Voltage Regulator Notes for Application Circuits: 1) 2) To improve the stability of output voltage , a 0.1µF capacitor between cathode and anode of APL431L is strongly recommended. Set VO according to the following equation: VO= VREF (1+R1/ R2)+ IREF R1 Choose the value for RB as follows: The maximum limit for RB should be such that the cathode current( IK) is greater than the minimum operating current (60µA) at VIN (MIN) . The minimum limit for RB should be such that the cathode current (IK) does not exceed 100mA under all load conditions, and the instantaneous turn-on value for IK does not exceed 150mA . Both of the following conditions must be met : RB,MIN ≥ VIN(MAX) / 150mA ( to limit instantaneous turn-on IK) RB,MIN ≥ VIN(MAX) - VO / IO (MIN) + 100mA (to limit IK under normal operating conditions) • • 3) Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 4 www.anpec.com.tw APL1431L Typical Characteristics 300 150 TA=25°C 200 TA=25°C 100 100 Cathode Current (mA) Cathode Current (µA) VKA=VREF VKA=VREF 50 0 0 -100 -50 -200 -100 -300 -1 -0.5 0 0.5 1 1.5 -150 -1.5 -1 -0.5 0 0.5 1 1.5 Cathode Voltage (V) Cathode Voltage (V) 1.248 1.246 150 Reference Input Current (nA) IK=10mA IK=10mA R1=10kΩ 125 Reference Voltage (V) 1.244 1.242 1.24 1.238 1.236 1.234 -40 R2=∞ 100 75 -20 0 20 40 60 80 100 50 -40 -20 0 20 40 60 80 100 Junction Temperature (°C) Junction Temperature (°C) Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 5 www.anpec.com.tw APL1431L Typical Characteristics (Cont.) Ratio of Delta Reference Voltage to Delta Cathode Voltage (-mV/V) 1.2 250 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -40 ∆VKA=16V to VREF Off State Cathode Current (nA) 1.1 IK=10mA VREF=0V 200 VKA=16V 150 100 50 0 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 Junction Temperature (°C) Junction Temperature (°C) Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 6 www.anpec.com.tw APL1431L Packaging Information SOT-23-5 e1 5 4 E1 E 1 2 3 e b D A2 A a L1 A1 L2 L D im A A1 A2 b D E E1 e e1 L L1 L2 N α M illimet ers M in. 0 .95 0.05 0.90 0 .30 2 .8 2 .6 1.5 0 .95BSC 1.90BSC 0 .35 0.20 BSC 0.5 5 0° 10° 0° 0.7 0.020 0.55 0.014 M ax. 1.45 0.15 1.30 0.50 3.00 3.00 1.70 M in. 0.037 0.002 0.035 0.011 0.110 0.102 0.059 Inches M ax. 0.057 0.006 0.051 0.019 0.118 0.118 0.067 0.037BSC 0.074BSC 0.022 0.008 BSC 0.028 5 10° Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 7 www.anpec.com.tw APL1431L Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition TP (IR/Convection or VPR Reflow) tp C ritical Zone T L to T P R am p-up T e m p e ra tu re TL T sm ax tL T sm in R am p-down ts Preheat 25 t 25 °C to Peak T im e Classificatin Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Large Body Small Body Pb-Free Assembly Large Body Small Body 3°C/second max. 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds 245 +0/-5°C 250 +0/-5°C 10-30 seconds 20-40 seconds 6°C/second max. 8 minutes max. www.anpec.com.tw Average ramp-up rate 3°C/second max. (TL to TP) Preheat - Temperature Min (Tsmin) 100°C - Temperature Mix (Tsmax) 150°C - Time (min to max)(ts) 60-120 seconds Tsmax to TL - Ramp-up Rate Tsmax to TL - Temperature(TL) 183°C - Time (tL) 60-150 seconds Peak Temperature(Tp) 225 +0/-5°C 240 +0/-5°C Time within 5°C of actual Peak 10-30 seconds 10-30 seconds Temperature(tp) Ramp-down Rate 6°C/second max. 6 minutes max. Time 25°C to Peak Temperature Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 8 Note: All temperatures refer to topside of the package. Measured on the body surface. APL1431L Reliability Test Program Test item S OLDERABILITY H OLT P CT T ST E SD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245 °C, 5 SEC 1000 Hrs Bias @125°C 168 Hrs, 100% RH, 121°C -65 °C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA Carrier Tape & Reel Dimensions t P P1 D Po E F W Bo Ao Ko D1 T2 J C A B T1 Application A 178 ±1 B 72 ± 1.0 D 1.5± 0.1 C J T1 8.4 ± 2 P1 T2 1.5 ± 0.3 Ao W 8.0 ± 0.3 Bo 3.2± 0.1 P 4 ± 0.1 Ko 1.4± 0.1 E 1.75± 0.1 t 0.2±0.033 (mm) 13.0 + 0.2 2.5 ± 0.15 D1 1.5± 0.1 Po 4.0 ± 0.1 SOT-23-5 F 3.5 ± 0.05 2.0 ± 0.1 3.15 ± 0.1 Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 9 www.anpec.com.tw APL1431L Cover Tape Dimensions Application SOT- 23-5 Carrier Width 8 Cover Tape Width 5.3 Devices Per Reel 3000 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright  ANPEC Electronics Corp. Rev. A.4 - May., 2003 10 www.anpec.com.tw