APL5933CKAI-TRG

APL5933A/B/C/D 3A, Ultra Low Dropout (0.19V Typical) Linear Regulator Features • General Description The APL5933A/B/C/D is a 3A ultra low dropout linear regulator. The IC needs two supply voltages, one is a Ultra Low Dropout - 0.19V (Typical) at 3A Output Current • control voltage (VCNTL) for the control circuitry, the other is a main supply Voltage(VIN) for power conversion, to re- Low ESR output Capasitor (Milti-layer Chip Capasitors (MLCC)) Applicable • • • • • duce power dissipation and provide extremely low dropout voltage. 0.8V Reference Voltage High Output Accuracy The APL5933A/B/C/D integrates many functions. A PowerOn-Reset (POR) circuit monitors both supply voltages on Fast Transient Response Adjustable Output Voltage VCNTL and VIN pins to prevent erroneous operations. The functions of thermal shutdown and current-limit protect Power-On-Reset Monitoring on Both VCNTL and the device against thermal and current over-loads. A POK indicates that the output voltage status with a delay time VIN Pins • • • • • • Internal Soft-Start set internally. It can control other converter for power sequence. APL5933A/B/C/D can be enabled by other Current-Limit and Short Current-Limit Protections Thermal Shutdown with Hysteresis power systems. Pulling and holding the EN voltage below 0.4V or ENB above 1.2V will shuts off the output. Open-Drain VOUT Voltage Indicator (POK) Low Shutdown Quiescent Current (< 30µA ) The APL5933A/B/C/D is available in a SOP-8P package which features small size as SOP-8 and an Exposed Built in Shutdown/Enable Control with floating high/ low Function • Pad to reduce the junction-to-case resistance to extend power range of applications. Simple SOP-8P and TDFN3x3-10 Packages with Exposed Pad • Lead Free and Green Devices Available (RoHS Compliant) Simplified Application Circuit VCNTL Applications • • • Motherboards, VGA Cards VIN VCNTL Notebook PCs POK Add-in Cards VIN POK VOUT VOUT APL5933 A/B/C/D EN Enable EN FB GND Optional ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright  ANPEC Electronics Corp. Rev. A.5 - Aug., 2017 1 www.anpec.com.tw APL5933A/B/C/D Pin Configuration POK EN VIN VCNTL 8 7 6 5 1 2 3 4 VOUT VOUT VOUT FB POK GND FB VOUT NC APL5933A/B/C/D SOP-8P (Top View) 1 2 3 4 5 10 VCNTL 9 VIN 8 VIN 7 VIN 6 EN GND APL5933A/B/C/D TDFN3x3-10 (Top View) = Exposed Pad (connected to ground plane for better heat dissipation) = Exposed Pad (connected to ground plane for better heat dissipation) Ordering and Marking Information Turn On Delay Time A : Initial High/2.7ms B : Initial High/0.5ms C : Initial Low/2.7ms D : Initial Low/0.5ms Package Code KA : SOP-8P QB : TDFN3x3-10 Operating Ambient Temperature Range I : -40 to 85 oC Handling Code TR : Tape & Reel Assembly Material G : Halogen and Lead Free Device APL5933 Assembly Material Handling Code Temperature Range Package Code Enable Function / Turn On Delay APL5933A KA : APL5933A APL5933B KA : APL5933B APL5933C KA : APL5933C APL5933D KA : APL5933D APL5933A QB : APL5933B QB : XXXXX - Date Code XXXXX XXXXX - Date Code XXXXX XXXXX - Date Code XXXXX XXXXX - Date Code XXXXX APL 5933A XXXXX - Date Code XXXXX APL 5933B XXXXX - Date Code XXXXX APL5933C QB : APL5933D QB : APL 5933C XXXXX - Date Code XXXXX APL 5933D XXXXX - Date Code XXXXX Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight). Copyright  ANPEC Electronics Corp. Rev. A.5 - Aug., 2017 2 www.anpec.com.tw APL5933A/B/C/D Absolute Maximum Ratings S ymbol VCN TL V IN VOUT (Note 1) Rat ing Unit V CNTL Supp ly Voltage (VCNTL to GND) Parameter -0.3 ~ 6 V V IN Supp ly Voltage (VIN to GND) -0.3 ~ 6 V -0.3 ~ V IN+0.3 V -0.3 ~ 6 V -0 .3 ~ V CNTL+0.3 V 2 .5 2 W V OUT to GND Voltage P OK to GND Voltage E N, FB to GND Vol tag e Maximum Power Dissipation, T A=25oC PD(MAX) TJ SOP- 8P TDFN3 x3- 10 Maximum Juncti on Temp erature ο 15 0 T STG Storag e Temp erature Rang e T SDR Maximum Lea d S olde ring Temperatur e, 10 Seconds C ο -65 ~ 150 C ο 26 0 C Note1: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Thermal Characteristics S ymbol Pa ra met er Junction -to- Ambie nt Resistan ce in Free Air Typical Value Unit (Note 2) θ JA SOP-8P TDFN3 x3- 10 50 60 o SOP-8P TDFN3 x3- 10 7 8 o C/W Junction -to- Ca se Resista nce in Free Air θ JC C/W Note 2: θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. The exposed pad of SOP-8P/TDFN3x3-10 is soldered directly on the PCB. Recommended Operating Conditions (Note3) Symbol VCNTL VIN Range Unit VCNTL Supply Voltage Parameter 3.0 ~ 5.5 V VIN Supply Voltage 1.2 ~ 5.5 V 0.8 ~ VIN – VDROP V 0~3 A 8 ~ 250 µF mΩ VOUT VOUT Output Voltage (when VCNTL-VOUT>2.1V) IOUT VOUT Output Current COUT VOUT Output Capacitance ESRCOUT IOUT = 0 to 3A at 25% nominal VOUT ESR of VOUT Output Capacitor 0 ~ 200 TA Ambient Temperature -40 ~ 85 ο TJ Junction Temperature -40 ~ 125 ο C C Note 3: Refer to the typical application circuit. Copyright  ANPEC Electronics Corp. Rev. A.5 - Aug., 2017 3 www.anpec.com.tw APL5933A/B/C/D Electrical Characteristics Unless otherwise specified. These specifications apply over VCNTL=5V, vIN=1.8v, VOUT=1.2V, and TA= -40 ~ 85oC, unless otherwise o specified. Typical values are at TJ=25 C. Symbol Parameter APL5933A/B/C/D Test Conditions Unit Min. Typ. Max. EN=VCNTL, IOUT=0A - 1.0 1.5 mA EN=GND or ENB=VCNTL - 20 30 µA VIN=5.5V, EN=GND or ENB=VCNTL - - 1 µA 2.5 2.7 2.9 V SUPPLY CURRENT IVCNTL VCNTL Supply Current VCNTL Supply Current at ISD Shutdown VIN Supply Current at Shutdown POWER-ON-RESET (POR) Rising VCNTL POR Threshold VCNTL POR Hysteresis - 0.4 - V 0.8 0.9 1.0 V - 0.5 - V 0.792 0.8 0.808 V -1.5 - +1.5 % - 0.06 0.25 % -0.15 - +0.15 %/V - 80 - Ω -100 - 100 nA - 0.24 0.29 TJ=-40~125 C - - 0.39 VCNTL=5.0V, TJ=25oC IOUT=3A VOUT=1.8V TJ=-40~125oC - 0.22 0.26 - - 0.35 - 0.21 0.25 - - 0.34 3.6 4.0 4.6 3.2 - - - 0.9 - A 1.5 3.4 - ms - 150 - o - 50 - o Rising VIN POR Threshold VIN POR Hysteresis OUTPUT VOLTAGE VREF Reference Voltage FB=VOUT Output Voltage Accuracy VCNTL =3.0~5.5V, IOUT= 0~3A, TJ= -40~125 oC Load Regulation IOUT=0A ~3A Line Regulation IOUT=10mA, VCNTL=3.0 ~ 5.5V VOUT Pull-Low Resistance VCNTL=5V, VEN=0V or VENB=5V, VOUT