AOZ8030DIL

8-Line EMI Filter with Integrated ESD Protection AOZ8030 General Description The AOZ8030 is an 8-line device integrating EMI filtering with ESD protection for each line. It is designed to suppress unwanted EMI/RFI signals and provide electrostatic discharge (ESD) protection in portable electronic equipment. This state-of-the-art device utilizes AOS leading edge Trench Vertical Structure [TVS]2 ™ technology for superior clamping performance and filter attenuation over the full operating display range. The AOZ8030 has been optimized for protection of color LCD displays and CCD camera lines in cellular phones and other portable consumer electronic devices. The AOZ8030 consists of eight identical circuits comprised of TVS diodes for ESD protection, and a resistor–capacitor network for EMI/RFI filtering. A series resistor value of 100Ω and a capacitance value of 28pF are used to achieve -35dB minimum attenuation from 800MHz to 3.0GHz. The TVS diodes provide effective suppression of ESD voltages in excess of ±20kV (air discharge) and ±20kV (contact discharge). This exceeds IEC 61000-4-2, level 4 ESD immunity test. The AOZ8030 comes in an RoHS compliant, 1.2mm x 3.5mm, 0.4mm pitch DFN package and is rated over a -40°C to +85°C ambient temperature range. Features ● 8 lines for EMI filtering and ESD protection: – Exceeds IEC 61000-4-2, level 4 (ESD) immunity test – ±20kV (air discharge) and ±20kV (contact discharge) Trench Vertical Structure [TVS]2 ™ based technology used to achieve excellent ESD clamping & filter performance over the full operating display range Filter performance: -35db attenuation from 800MHz to 3.0GHz Low operating voltage: 5.0V Capacitance stability over wide range of voltages and temperatures DFN package: 1.2mm x 3.5mm, 0.4mm pitch Pb-Free device Green product ● ● ● ● ● ● ● Applications ● ● ● EMI filtering and ESD protection for data lines LCD displays, camera interface, I/O interface Portable handheld devices, cell phones, PDA phones Typical Application D0 100Ω CH1 28pF 28pF 100Ω D1 CH2 LCD/Camera Module 28pF 28pF D7 100Ω CH8 28pF 28pF Figure 1 Rev. 1.8 January 2009 www.aosmd.com Page 1 of 7 AOZ8030 Ordering Information Part Number AOZ8030DIL Ambient Temperature Range -40°C to +85°C Package DFN-16 Environmental RoHS Compliant Green Product All AOS products are offered in packages with Pb-free plating and compliant to RoHS standards. Parts marked as Green Products (with “L” suffix) use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration 1 16 16 15 1 2 2 15 3 14 Exposed Pad (GND) 14 13 12 11 10 9 3 4 13 4 5 6 6 11 5 12 7 8 7 10 DFN-16 (Bottom View) 8 9 Top View Pin Description Pin Number 1,16 2, 15 3, 14 4, 13 5, 12 6, 11 7, 10 8, 9 Exposed Pad Pin Name CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8 GND Pin Function Channel 1 Connections Channel 2 Connections Channel 3 Connections Channel 4 Connections Channel 5 Connections Channel 6 Connections Channel 7 Connections Channel 8 Connections Common Ground Connection Rev. 1.8 January 2009 www.aosmd.com Page 2 of 7 AOZ8030 Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Storage Temperature (TS) ESD Rating per IEC61000-4-2, contact ESD Rating per IEC61000-4-2, air (1) (1) Rating -65°C to +150°C ±20kV ±20kV ±30kV ESD Rating per Human Body Model(2) Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5kΩ. Electrical Characteristics TA = 25°C unless otherwise specified. Symbol VRWM VBR IR VCL Parameter Reverse Working Voltage Reverse Breakdown Voltage Reverse Leakage Current Signal Clamp Voltage (3) Conditions IT = 1mA(4) Min. 6 Typ. 7 Max. 5.0 8 0.1 Units V V µA V VRWM = 3.3V ILOAD = 1A, positive ILOAD = 1A, negative clamp(5)(8) ILOAD = 5A, positive clamp(5)(8) ILOAD = 5A, negative clamp(5)(8) ILOAD = 12A, positive clamp(5)(8) ILOAD = 12A, negative clamp(5)(8) clamp(5)(8) 7.00 -3.00 8.00 -5.00 10.00 -10.00 90 26 100 28 90 -35 -35 110 30 RCH CCH fC Total Series Resistance Channel Capacitance Cut-off Frequency Attenuation from 800MHz to 3.0GHz Attenuation from 800MHz to 3.0GHz IR = 20mA Input to Ground(6)(7)(8) Measured with 50Ω source and 50Ω load termination VR = 0V Measured with 50Ω source and 50Ω load termination VR = 5V Measured with 50Ω source and 50Ω load termination Ω pF MHz dB dB Notes: 3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 4. VBR is measured at the pulse test current IT. 5. Measurements performed using a 100ns Transmission Line Pulse (TLP) system. 6. Total capacitance is equal to 2 x CCH. 7. Measured at 25°C, VR = 2.5V, f = 1.0MHz. 8. Guaranteed by design. Rev. 1.8 January 2009 www.aosmd.com Page 3 of 7 AOZ8030 Typical Performance Characteristics Insertion Loss Characteristics 0 -5 Typical Line Capacitance vs. Reverse Bias Voltage (Normalized to Capacitance @ 2.5V) 1.8 1.6 Normalized Capacitance 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -10 -15 S21 (db) -20 -25 -30 -35 -40 -45 -50 1 10 100 Frequency (MHz) 1000 10000 1.0 2.0 3.0 4.0 5.0 Reverse Biased Voltage (V) Analog Crosstalk 0 11 Clamping Voltage vs. Peak Pulse Current Clamping Voltage, Vcl (V) -20 10 S21 (db) -40 9 -60 8 -80 7 -100 1 10 100 Frequency (MHz) 1000 10000 6 0 2 4 6 8 10 12 Peak Pulse Current, Ipp (A) Forward Voltage vs. Forward Current 12 110 Typical Resistance vs. Temperature 10 Forward Voltage (V) Resistance (Ω) 105 8 100 6 4 95 2 0 2 4 6 8 10 12 Forward Current (A) 90 -45 -25 -5 5 25 45 65 85 Temparature (°C) Rev. 1.8 January 2009 www.aosmd.com Page 4 of 7 AOZ8030 Package Dimensions, DFN 3.5 x 1.2, 16L D b D1 E L Pin 1 Marking E1 TOP VIEW e BOTTOM VIEW Pin 1 ID (C0.2x45°) A A1 SIDE VIEW A3 RECOMMENDED LAND PATTERN 2.80 0.15 0.20 0.20 0.15 0.20 Dimensions in millimeters Symbols A A1 A3 b D D1 Min. 0.50 0.00 Nom. 0.55 Max. 0.60 Dimensions in inches Symbols A A1 A3 b D D1 E E1 e L Min. 0.020 0.000 Nom. 0.022 Max. 0.024 — 0.05 0.152 Ref. 0.15 0.20 0.25 3.45 2.75 1.15 0.25 0.20 3.50 2.80 3.55 2.85 — 0.002 0.006 Ref. 0.006 0.008 0.010 0.136 0.108 0.045 0.010 0.008 0.138 0.110 0.140 0.112 0.30 1.00 E E1 e L 1.20 1.25 0.30 0.35 0.40 BSC 0.25 0.30 0.047 0.049 0.012 0.014 0.016 BSC 0.010 0.012 0.30 0.40 0.20 Notes: 1. All dimensions are in millimeters. Angles is degree. 2. Warpage shall not exceed 0.10mm. 3. Marking is for package orientation reference only. Rev. 1.8 January 2009 www.aosmd.com Page 5 of 7 AOZ8030 Tape & Reel Dimensions, DFN 3.5 x 1.2, 16L Carrier Tape K0 P1 P2 D0 E1 E2 B1 B0 E (B2) (A2) A0 A1 UNIT: mm Package DFN 3.5x1.2 T 0.30 ±0.05 B0 3.80 ±0.1 B1 3.75 ±0.1 B2 4.16 A0 1.50 ±0.1 A1 1.45 ±0.1 A2 1.86 K0 0.75 ±0.1 D0 ø1.55 ±0.05 E 12.00 ±0.3 E1 1.75 ±0.1 E2 5.50 ±0.05 0.15 P0 0.15 T Feeding Direction P0 4.00 ±0.10 P1 4.0 ±0.1 P2 2.00 ±0.05 Reel B W1 S K 60° 120° M N H 2.84 B 2.24 W Arbor Hole Detail A Scale 2:1 Front View Back View Unit: mm Tape Size Reel Size 12mm ø1800 Section: B-B M ø179.0 +1.0 N ø60.0 ±0.5 W 13.0 ±0.5 W1 17.0 H ø13.0 ±0.2 K 10.5 ±0.25 S 1.8 (Bottom) Leader / Trailer & Orientation Trailer Tape 300mm Min. Components Tape Orientation in Pocket Leader Tape 500mm Min. Rev. 1.8 January 2009 www.aosmd.com Page 6 of 7 AOZ8030 Package Marking ABH1F Part Number Code Underscore Denotes Green Product Assembly Lot Code Week and Year Code This data sheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Rev. 1.8 January 2009 www.aosmd.com Page 7 of 7