AOZ8809DI-03

AOZ8809DI Ultra-Low Capacitance TVS Diode General Description Features The AOZ8809DI is a transient voltage suppressor array designed to protect high speed data lines such as HDMI 1.4/2.0, USB 3.0/3.1, MDDI, SATA, and Gigabit Ethernet from damaging ESD events.  ESD protection for high-speed data lines: This device incorporates eight surge rated, low capacitance steering diodes and a TVS in a single package. During transient conditions, the steering diodes direct the transient to either the positive side of the power supply line or to ground. The AOZ8809DI provides a typical line-to-line capacitance of 0.25 pF and low insertion loss up to 6 GHz providing greater signal integrity making it ideally suited for HDMI 1.4/2.0 or USB 3.0/3.1 applications, such as Digital TVs, DVD players, computing, set-top boxes and MDDI applications in mobile computing devices. The AOZ8809DI comes in a RoHS compliant and Halogen Free 2.5 mm x 1.0 mm x 0.55 mm DFN-10 package and is rated for -40 °C to +85 °C junction temperature range. – IEC 61000-4-2, level 4 (ESD) immunity test – Air discharge: ±15 kV; contact discharge: ±15 kV – IEC61000-4-4 (EFT) 40 A (5/50 nS) – IEC61000-4-5 (Lightning) 4 A (8/20 µS) – Human Body Model (HBM) ±24 kV  Array of surge rated diodes with internal TVS diode  Small package saves board space  Protects four I/O lines  Low capacitance between I/O lines: 0.25 pF  Low clamping voltage  Low operating voltage: 3.3V, 5.0 V Applications  HDMI 1.4/2.0, USB 3.0/3.1, MDDI, SATA ports  Monitors and flat panel displays  Set-top box  Video graphics cards  Digital Video Interface (DVI)  Notebook computers Typical Applications AOZ8809 AOZ8809 AOZ8802A TX2+ TX2D+ DUSB 3.0/3.1 Transceiver D+ DUSB 3.0/3.1 Connector SSRX+ SSRX- SSRX+ SSRX- TX1+ TX1HDMI 1.4/2.0 Transmitter TX0+ TX0- SSTX+ SSTX- SSTX+ SSTX- CLK+ CLK- RX2+ RX2RX1+ RX1HDMI 1.4/2.0 Receiver RX0+ RX0CLK+ CLKConnector AOZ8809 AOZ8809 Figure 1. USB 3.0/3.1 Ports Rev. 7.0 June 2021 Connector AOZ8809 Figure 2. HDMI 1.4/2.0 Ports www.aosmd.com Page 1 of 7 AOZ8809DI Ordering Information Part Number Ambient Temperature Range Package Environmental -40 °C to +85 °C 2.5 mm x 1.0 mm x 0.55 mm DFN-10 Green Product AOZ8809DI-03 AOZ8809DI-05 AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/media/AOSGreenPolicy.pdf for additional information. Pin Configuration CH1 1 10 NC CH2 2 9 NC VN 3 8 VN CH3 4 7 NC CH4 5 6 NC DFN-10 (Top View) Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter AOZ8809DI-03 Storage Temperature (TS) -65 °C to +150 °C ESD Rating per IEC61000-4-2, contact(1)(3) ESD Rating per IEC61000-4-2, air AOZ8809DI-05 ±15 kV (1)(3) ESD Rating per Human Body Model ±15 kV (2)(3) ±24 kV Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330 Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100 pF, RDischarge = 1.5 kΩ. Maximum Operating Ratings Parameter Rating Junction Temperature (TJ) Rev. 7.0 June 2021 -40 °C to +125 °C www.aosmd.com Page 2 of 7 AOZ8809DI Electrical Characteristics TA = 25°C unless otherwise specified. Symbol Parameter Diagram IPP Maximum Reverse Peak Pulse Current VCL Clamping Voltage @ IPP 100ns Transmission Line Pulse (TLP) VESD ESD Clamping Voltage (IEC61000-4-2 +6kV Contact Discharge) VRWM Working Peak Reverse Voltage IR VBR I VCL VBR VRWM Maximum Reverse Leakage Current Breakdown Voltage IT Test Current VF Forward Voltage @ IF CJ Max. Capacitance @ VR = 0 and f = 1 MHz Device IF V IR VF IT IPP VBR (V) VCL Max.(3) VESD (V)(3) V (V) I (µA) V (V) Min. Device RWM R F IT = 100 A Max. Max. Typ. IPP = 2 A IPP = 12 A Marking Typ. CJ (pF)(3,4) Typ. Max. AOZ8809DI-03 H 3.3 3.5 1.0 0.85 3.5 8.0 8.0 0.45 0.6 AOZ8809DI-05 K 5.0 6.0 1.0 0.85 4.0 9.0 8.0 0.45 0.6 Notes: 3. These specifications are guaranteed by design and characterization. 4. VPIN 3,8 = 0V, VIN = 2.5V, f = 1MHz, T = 25˚C, any I/o pin to Ground. Rev. 7.0 June 2021 www.aosmd.com Page 3 of 7 AOZ8809DI Typical Performance Characteristics Forward Voltage vs. Forward Peak Pulse Current 8 (tperiod = 100ns, tr = 1ns) 10 Clamping Voltage, VCL (V) AOZ8809DI-3 7 Forward Voltage (V) Clamping Voltage vs. Peak Pulse Current (tperiod = 100ns, tr = 1ns) AOZ8809DI-5 6 5 4 3 2 1 0 AOZ8809DI-3 9 AOZ8809DI-5 8 7 6 5 4 3 2 0 2 4 6 8 10 Forward Current, IPP (A) 12 0 14 2 4 6 8 10 Peak Puse Current, IPP (A) 12 14 Capacitance vs. Frequency (IO to GND) Typical Variation of CIN vs. VIN 0.8 1E-12 8E-13 0.6 Capacitance (F) Capacitance (pF) 0.7 0.5 0.4 0.3 0.2 4E-13 2E-13 AOZ8809DI-3 AOZ8809DI-5 0.1 0 6E-13 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Input Voltage (V) 4.0 4.5 5.0 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency (MHz) Transmission Line Pulsing (TLP) Measurement 20 TLP Current (A) 18 16 14 12 10 8 6 4 2 1.5 Rev. 7.0 June 2021 2.0 2.5 3.0 3.5 4.0 4.5 TLP Voltage (V) www.aosmd.com 5.0 5.5 6.0 Page 4 of 7 AOZ8809DI Typical Performance Characteristics (Continued) Insertion Loss vs. Frequency (IO to GND) 0 Insertion Loss S21 (dB) Insertion Loss S21 (dB) 0 -2 -4 -6 -8 -10 10,000 Insertion Loss vs. Frequency (IO to IO) -2 -4 -6 -8 -10 10,000 100,000 1,000,000 Frequency (kHz) USB 3.1 Eye Diagram with AOZ8809 (10Gbps) 400m Voltage (V) Differential Signal (V) USB 3.0 Eye Diagram with AOZ8809 (5Gbps) 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Unit Intervals 100,000 1,000,000 Frequency (kHz) -400m -100 Time (s) 100p HDMI 2.0 Eye Diagram with AOZ8809 HDMI 1.4 Eye Diagram with AOZ8809 600m Voltage (V) Voltage (V) 875m -600m -875m 0 Rev. 7.0 June 2021 Time (s) 898p www.aosmd.com 0 Time (s) 300p Page 5 of 7 AOZ8809DI High Speed PCB Layout Guidelines Printed circuit board layout is the key to achieving the highest level of surge immunity on power and data lines. The location of the protection devices on the PCB is the simplest and most important design rule to follow. The AOZ8809DI devices should be located as close as possible to the noise source. The AOZ8809DI device should be placed on all data and power lines that enter or exit the PCB at the I/O connector. In most systems, surge pulses occur on data and power lines that enter the PCB through the I/O connector. Placing the AOZ8809DI devices as close as possible to the noise source ensures that a surge voltage will be clamped before the pulse can be coupled into adjacent PCB traces. In addition, the PCB should use the shortest possible traces. A short trace length equates to low impedance, which ensures that the surge energy will be dissipated by the AOZ8809DI device. Long signal traces will act as antennas to receive energy from fields that are produced by the ESD pulse. By keeping line lengths as short as possible, the efficiency of the line to act as an antenna for ESD related fields is reduced. Minimize interconnecting line lengths by placing devices with the most interconnect as close together as possible. The protection circuits should shunt the surge voltage to either the reference or chassis ground. Shunting the surge voltage directly to the IC’s signal ground can cause ground bounce. The clamping performance of TVS diodes on a single ground PCB can be improved by minimizing the impedance with relatively short and wide ground traces. The PCB layout and IC package parasitic inductances can cause significant overshoot to the TVS’s clamping voltage. The inductance of the PCB can be reduced by using short trace lengths and multiple layers with separate ground and power planes. One effective method to minimize loop problems is to incorporate a ground plane in the PCB design. The AOZ8809DI ultra-low capacitance TVS is designed to protect four high speed data transmission lines from transient over-voltages by clamping them to a fixed reference. The low inductance and construction minimizes voltage overshoot during high current surges. When the voltage on the protected line exceeds the reference voltage the internal steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. The AOZ8809DI is designed for ease of PCB layout by allowing the traces to run underneath the device. The pinout of the AOZ8809DI is designed to simply drop onto the IO lines of a High Definition Multimedia Interface (HDMI 1.4/2.0) or USB 3.0/3.1 design without having to divert the signal lines that may add more parasitic inductance. Pins 1, 2, 4 and 5 are connected to the internal TVS devices and pins 6, 7, 9 and 10 are no connects. The no connects was done so the package can be securely soldered onto the PCB surface. Clock Clock SSRX+ SSRX+ Data0 Data0 SSRX– SSRX– Ground Ground Ground Data1 Data1 SSTX+ SSTX+ Data2 Data2 SSTX– SSTX– Ground Figure 3. Flow Through Layout for HDMI 1.4/2.0 Figure 4. Flow Through Layout for USB 3.0/3.1 . Rev. 7.0 June 2021 www.aosmd.com Page 6 of 7 AOZ8809DI LEGAL DISCLAIMER Applications or uses as critical components in life support devices or systems are not authorized. AOS does not assume any liability arising out of such applications or uses of its products. AOS reserves the right to make changes to product specifications without notice. It is the responsibility of the customer to evaluate suitability of the product for their intended application. Customer shall comply with applicable legal requirements, including all applicable export control rules, regulations and limitations. AOS' products are provided subject to AOS' terms and conditions of sale which are set forth at: http://www.aosmd.com/terms_and_conditions_of_sale LIFE SUPPORT POLICY ALPHA AND OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 7.0 June 2021 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 7 of 7