VRE104C

VRE104 VRE104 VRE104 Precision Voltage Reference FEATURES ♦ Very High Accuracy: +4.5 V Output, ±0.8 mV ♦ Extremely Low Drift: 1.48 ppm/°C (-55°C to +125°C) ♦ Excellent Stability: 6 ppm/1000 Hrs. Typical ♦ Excellent Line Regulation: 6 ppm/V Typical ♦ Wide Supply Range: +13.5 to +22.0 V ♦ Hermetic 14-pin Ceramic DIP ♦ Military Processing Options APPLICATIONS ♦ Precision A/D And D/A Converters ♦ Transducer Excitation ♦ Accurate Comparator Threshold Reference ♦ High Resolution Servo Systems ♦ Digital Voltmeters ♦ High Precision Test and Measurement Instruments DESCRIPTION VRE104 Series Precision Voltage References provide ultrastable +4.5 V outputs with up to ±0.8 mV initial accuracy and temperature coefficient as low as 1.48 ppm/°C over the full military temperature range. These references are specifically designed to be used with the Crystal Semiconductor line of successive-approximation type Analog to Digital Converters (ADCs). This line of ADCs sets new standards for temperature drift, which can only be as good as the external reference used. The VRE104 combined with an ADC will provide the lowest drift data conversion obtainable. VRE104 series devices are available in two operating temperature ranges, -25°C to +85°C and -55°C to +125°C, and two performance grades. All devices are packaged in 14-pin hermetic ceramic packages for maximum long-term stability. “M” versions are screened for high reliability and quality. Superior stability, accuracy, and quality make the VRE104 ideal for all precision applications which may require a 4.5 V reference. High-accuracy test and measurement instrumentation, and transducer excitation are some other applications which can benefit from the high accuracy of the VRE104. Figure 1. BLOCK DIAGRAM www.apexanalog.com VRE104DS Copyright © Apex Microtechnology, Inc. 2012 (All Rights Reserved) SEP 2012 1 VRE104DS REVI VRE104 SELECTION GUIDE Output (V) Temperature Operating Range Volt Deviation (MAX) VRE104C VRE104CA +4.5 +4.5 -25°C to +85°C -25°C to +85°C ±0.49mV ±0.40mV VRE104MA +4.5 -55°C to +125°C ±0.60mV Model Hermetic 14-pin Ceramic DIP Package Style HC 1. CHARACTERISTICS AND SPECIFICATIONS ELECTRICAL SPECIFICATIONS VPS =+15V, T = 25°C, RL = 10K Ω UNLESS OTHERWISE NOTED. Grade VRE104C Parameter Min Typ VRE104CA Max Min Typ VRE104MA Max Min Typ Max Units ABSOLUTE MAXIMUM RATINGS Power Supply +13.5 +22 * * * * V Operating Temperature -25 +85 * * -55 +125 ºC Storage Temperature -65 +150 * * * * ºC Short Circuit Protection Continuous * * +4.5 * * OUTPUT VOLTAGE VRE104 V OUTPUT VOLTAGE ERRORS Initial Error ±890 Warmup Drift TMIN - TMAX ±800 2 (Note1) ±800 1 490 1 400 µV ppm 600 µV Long-Term Stability 6 * * ppm/1000hrs Noise (0.1 - 10Hz) 3 * * µVpp OUTPUT CURRENT Range ±10 * * mA REGULATION Line 6 10 * * * * ppm/V Load 3 * * ppm/mA Range 10 * * mV Temperature Coefficient 4 * * µV/ºC/mV OUTPUT ADJUSTMENT POWER SUPPLY CURRENT (Note 2) VRE104 +PS 5 7 * * * * mA NOTES: * Same as C Models. 1. Using the box method, the specified value is the maximum deviation from the output voltage at 25°C over the specified operating temperature range. 2. The specified values are unloaded. 2 VRE104DS VRE104 2. TYPICAL PERFORMANCE GRAPHS 0.49 0.4 -0.49 -0.4 Temperature oC VRE104C QUIESCENT CURRENT VS. TEMP Temperature oC VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE VOUT vs. TEMPERATURE 0.6 -0.6 Temperature oC VRE104CA JUNCTION TEMP. RISE VS. OUTPUT CURRENT Output Current (mA) Temperature oC VRE104MA PSRR VS. FREQUENCY Frequency (Hz) 3. THEORY OF OPERATION The following discussion refers to the block diagram in Figure 1. A FET current source is used to bias a 6.3 V zener diode. The zener voltage is divided by the resistor network R1 and R2. This voltage is then applied to the noninverting input of the operational amplifier which amplifies the voltage to produce a 4.5 V output. The gain is determined by the resistor networks R3 and R4: G=1 + R4/R3. The 6.3 V zener diode is used because it is the most stable diode over time and temperature. The current source provides a closely regulated zener current, which determines the slope of the references’ voltage vs. temperature function. By trimming the zener current a lower drift over temperature can be achieved. But since the voltage vs. temperature function is nonlinear, this method leaves a residual error over wide temperature ranges. To remove this residual error, a nonlinear compensation network of thermistors and resistors has been developed that is used in the VRE104 series references. This proprietary network eliminates most of the nonlinearity in the voltage vs. temperature function. By then adjusting the slope, the VRE104 series produces a very stable voltage over wide temperature ranges. This network is less than 2% of the overall network resistance so it has a negligible effect on long term stability. VRE104DS 3 VRE104 4. APPLICATION INFORMATION The proper connection of the VRE104 series voltage references is shown below with the optional trim resistors. Pay careful attention to the circuit layout to avoid noise pickup and voltage drops in the lines. The VRE104 series voltage references have the ground terminal brought out on two pins (pin 6 and pin 7) which are connected together internally. This allows the user to achieve greater accuracy when using a socket. Voltage references have a voltage drop across their power supply ground pin due to quiescent current flowing through the contact resistance. If the contact resistance was constant with time and temperature, this voltage drop could be trimmed out. When the reference is plugged into a socket, this source of error can be as high as 20 ppm. By connecting pin 7 to the power supply ground and pin 6 to a high impedance ground point in the measurement circuit, the error due to the contact resistance can be eliminated. If the unit is soldered into place, the contact resistance is sufficiently small that it does not effect performance. VRE104 Used With Crystal Semiconductor ADC Suggested Reading: Crystal Semiconductor Application Note “Voltage References for the CS501X/CS25IIX Series of A/D Converters" EXTERNAL CONNECTIONS 1. Optional Fine Adjust for approximately ±10mV. PIN CONFIGURATION TOP VIEW NC FINE ADJ. NC +4.5V FINE ADJ. NC NC NC REF. GND GND 4 VRE104 +PS NC NC NC VRE104DS VRE104 NEED TECHNICAL HELP? CONTACT APEX SUPPORT! For all Apex Microtechnology product questions and inquiries, call toll free 800-546-2739 in North America. For inquiries via email, please contact apex.support@apexanalog.com. International customers can also request support by contacting their local Apex Microtechnology Sales Representative. To find the one nearest to you, go to www.apexanalog.com IMPORTANT NOTICE Apex Microtechnology, Inc. has made every effort to insure the accuracy of the content contained in this document. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (expressed or implied). Apex Microtechnology reserves the right to make changes without further notice to any specifications or products mentioned herein to improve reliability. This document is the property of Apex Microtechnology and by furnishing this information, Apex Microtechnology grants no license, expressed or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Apex Microtechnology owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Apex Microtechnology integrated circuits or other products of Apex Microtechnology. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. APEX MICROTECHNOLOGY PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN PRODUCTS USED FOR LIFE SUPPORT, AUTOMOTIVE SAFETY, SECURITY DEVICES, OR OTHER CRITICAL APPLICATIONS. PRODUCTS IN SUCH APPLICATIONS ARE UNDERSTOOD TO BE FULLY AT THE CUSTOMER OR THE CUSTOMER’S RISK. Apex Microtechnology, Apex and Apex Precision Power are trademarks of Apex Microtechnolgy, Inc. All other corporate names noted herein may be trademarks of their respective holders. www.apexanalog.com VRE104DS Copyright © Apex Microtechnology, Inc. 2012 (All Rights Reserved) SEP 2012 5 VRE104DS REVI