AGH100-48S3V3P-4L

POWER AGH100 Series Half Brick Fully Regulated DCDC Converter Data Sheet Output Power: 82.5 Watts Input Voltage: 36 - 75 V Single Output: 3.3 V Special features ƒƒ 2:1 wide input range ƒƒ Optimised for high density, small space applications ƒƒ Low ripple and noise ƒƒ Fixed switching frequency Electrical Specifications ƒƒ High efficiency Input ƒƒ High capacitive load capability Input ra­nge 36 - 75 VDC ƒƒ Basic insulation system Input surge 100 V for 100 ms ƒƒ Pre-bias start-up capability Efficiency 92.4% (3.3 V) ƒƒ Openframe structure with Baseplate option Output Output voltage 3.3 Vdc Safety Trim range +10% to =20% Vout Output current 25 A Noise/ripple 45 mV pk-pk Regulation Load regulation 16.5 mV, Line regulation = 6.6 mV Switching frequency Fixed switching frequency 270 KHz Isolation voltage 2000 Vdc Transient response 80 mV deviation 80 µs recovery (25% deviation from 50% Iout, 0.1 A/µs) typical ƒƒ UL, cUL: UL60950 ƒƒ TUV/CE: IEC/EN60950 Control Enable TTL compatible Positive or Negative enable Environmental Specifications Operating ambient temperature range -40 °C to +85 °C Storage temperature -55 °C to +125 °C OTP 118 °C MTBF @ 25 °C 2 Million hours (Vin 48 V, Io = 20 A AGH100 Series Data Sheet Ordering Information Model number - Pin Assignments Input voltage Output voltage Power Efficiency Pin # Function +V in AGH100-48S3V3P-4L 48 V 3.3 V 25 A 92.4% 1 AGH100-48S3V3-4L 48 V 3.3 V 25 A 92.4% 2 Enable Case AGH100-48S3V3PB-4L 48 V 3.3 V 25 A 92.4% 3 AGH100-48S3V3B-4L 48 V 3.3 V 25 A 92.4% 4 -V in 5 -V out 6 -Sense 7 Trim 8 +Sense 9 +V out Standard converter is Negative enable “B” = Baseplate option “-4” = 4.8 mm pin length “-P” = Positive remote control “-L” = RoHS 6 compliant Mechanical Drawing - Open Frame 57.9 [2.280] 3 6 Bottom view 2 7 8 50 8 [2 000] 5 35.56 [1.400] 4 15.24 [0.600] 35.56 [1.400] 7.62 [0.300] 50.8 [2.000] 61.0[2.402] 48.26 [1.900] 9 1 4-Ф4.3 L 10.0 [0.394] Side view 7-Ф1.0±0.1 7-Ф2.0±0.1 Load board Unit: mm[inch] 2-Ф2.0±0.1 Bottom view: pin on upside Tolerance: X.Xmm±0.5mm[X.X in.±0.02in.] X.XXmm±0.25mm[X.XX in.±0.01in.] Notes: 1. 20 MHz bandwidth. External 10 uF tantalum capacitor placed across +Vout and –Vout; 33 uF e-cap or equivalent placed across +Vin and –Vin. 2. Efficiency measurements taken at full load and nominal line and Tamb = 25 °C 3. All specifications taken at nominal line, full load and Tamb = 25 °C unless otherwise noted. 4. Mechanical dimensions are for reference only. Dimensions are in MM. Mechanical tolerance = +/- 0.5 mm 5. Technical reference notes should be consulted for detailed information when available. 6. All specifications subject to change without notice. 7. Warranty 2 years. 8. The through-hole terminated modules are intended for wave-soldering process; special request for other manufacturing processes to be made to Artesyn. WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 South Diablo Way Suite B100 Tempe, AZ 85282, USA +1 888 412 7832 Ground Floor Offices, Barberry House 4 Harbour Buildings, Waterfront West Brierley Hill, West Midlands DY5 1LN, UK +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 Artesyn Embedded Technologies, Artesyn Embedded Power, Artesyn, and all Artesyn related logos are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. © 2019 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com For more information: www.artesyn.com For support: productsupport.ep@artesyn.com AGH100 DS 18Nov2019