AIF40C300N-NTL

ARTESYN AIF 300V Vin SERIES Advanced Energy's Artesyn AIF 300V Vin series of high voltage DC-DC converters comprises six single output models offering voltages of 1.8 V, 3.3 V, 5.0 V, 12 V, 15 V or 24 V. Designed for use with power factor correction (PFC) modules, the converters accept a wide range input of 250 to 420 VDC. They have a 600 watt continuous power rating at baseplate temperatures from -20 to 100˚C and can start up from temperatures as low as -40˚C. The output voltage can be adjusted using an analog signal, external resistor or digital data – there is a built-in I2C interface. The output of the 1.8 V and 3.3 V converters can be adjusted from 50% to 110% of nominal, while the 5 V, 12 V, 15 V and 24 V converters can be adjusted from 80% to 120% of nominal. Overvoltage and overcurrent protection thresholds can also be set by analog or digital control. SPECIAL FEATURES  EU Directive 2002/95/EC compliant  Maximum 600 W continuous power at  Two years warranty Maximum Power: 600 Watts Input Voltage: 300 VDC # of Outputs: Single for RoHS 100°C baseplate temperature 3 AT A GLANCE 3  108 W/in (6.6 W/cm )  High efficiency - up to 90%  Low output ripple and noise  Positive and Negative enable function  Excellent transient response  OVP, OCP, V Adj control with ALP™ SAFETY  UL UL62368-1 Recognized  CUL UL62368-1 Recognized  TUV EN62368-1 Licensed  CE Mark  UKCA Mark analog mode linear control, or through I2C bus with digital mode control  Paralleable with accurate current sharing ©2022 Advanced Energy Industries, Inc. AIF 300V Vin SERIES ELECTRICAL SPECIFICATIONS Input Input range 250 to 420 VDC Input surge 450 V / 100 ms Efficiency 90% @ 5.0 V (Typical) Output Load regulation 0.2% typical down to no load Line regulation 0.2% typical Noise ripple 100 mV typical (below 5 V); 2% typical (5 V and above) Remote sense Up to 0.5 V Output voltage adjust range +/-20% for 5 V and above; +10%/-50% for below 5 V Transient response 5% max for 3.3 V and above, 150 mV for 1.8 V , deviation with 25% to 75% full load 250 μS (max) recovery Current share accuracy 3% typical Overvoltage protection 115% Vo (nominal) Current limit 115% Io maximum Isolation Voltage adjust 80 to 120% Vo linear programming for 12 V, 15 V, 24 V, 48 V. 50% to 110% for 1.8 V to 5.0 V Enable TTL compatible (positive & negative enable options) Current limit adjust 20 to 100% Io linear programming or digital mode control Clock input (external sync) 3.3 to 5.5 Vp-p @ 800 KHz ±10% Clock output (internal clock) 4.5 Vp-p typical@ 800 KHz ±5% Power good identification High (Vo) = power good Temperature monitor output 10 mV/°K (2.73 = 0°C) Current monitor output 0 to 1 mA (1 mA = 100% Io rated) Overvoltage protection adjust 110 to 150% Vo linear programming by voltage or resistor, or digital mode control Notes: Nominal values apply with sense pins connected and other control pin unconnected. ALP: Astec Linear Programming ENVIRONMENTAL SPECIFICATIONS Operating temperature -20°C to +100°C (case temperature) Start up temperature -40°C to +100°C (case temperature) Storage temperature -40°C to +125°C Overtemperature protection 110°C max 2 advancedenergy.com AIF 300V Vin SERIES ORDERING INFORMATION Input Voltage Output Voltage Efficiency Model Number 300 VDC 1.8 V @ 120 A 80% (Typ) AIF120Y300 *-**L 300 VDC 3.3 V @ 120 A 87% (Typ) AIF120F300 *-**L 300 VDC 5.0 V @ 80 A 90% (Typ) AIF80A300 *-**L 300 VDC 12 V @ 50 A 90% (Typ) AIF50B300 *-**L 300 VDC 15 V @ 40 A 90% (Typ) AIF40C300 *-**L 300 VDC 24 V @ 25 A 90% (Typ) AIF25H300 *-**L 1. For Negative enable, add suffix “-N”. 2. For Non-thread hole, add suffix “-NT”. 3. For RoHS 6, add suffix “-L”. PIN ASSIGNMENTS Input (DC) Output (DC) Control Pins 31. Positive 21. Positive 1. +Sense 32. Negative 22. Positive 2. Temp Mon 23. Positive 3. C Mon 24. Positive 4. C Share 25. Negative 5. Clk Out 26. Negative 6. Clk In 27. Negative 7. PG/ID 28. Negative 8. C Lim Adj 9. OVP Adj 10. V Adj 11. Enable 12. -Sense advancedenergy.com 3 AIF 300V Vin SERIES MECHANICAL DRAWINGS 4 advancedenergy.com ABOUT ADVANCED ENERGY Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. For international contact information, visit advancedenergy.com. powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 Specifications are subject to change without notice. Not responsible for errors or omissions. ©2022 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks of Advanced Energy Industries, Inc. ENG-AIF 300V Vin SERIES-235-02 3.21