BXB100-48S05FLTJ

ARTESYN BXB SERIES 66 - 100 Watts XXXX DATA SHEET Total Power: 66 - 100 W Input Voltage: 18 - 36 V 36 - 75 V SPECIAL FEATURES # of Outputs:  Industry standard footprint 3  High power density (36.5 W/in ) Single  MTBF >1.4 million hours (Bellcore 332)  Input voltage to ETS300-132-2  Adjustable output voltage  No minimum load required  Separate case ground pin  Undervoltage lockout (UVLO)  UL, VDE and CSA safety approvals  Two year warranty SAFETY  VDE0805/EN60950/IEC950  UL1950  CSA C22.2 No. 950 ©2020 Advanced Energy Industries, Inc. BXB100 ELECTRIC Input Input voltage range 24 Vin nominal 48 Vin nominal 18 - 36 Vdc 36 - 75 Vdc Input current No load Remote OFF 100 mA max. 20 mA max. Input current (max.) (See Note 4) 48 V models 4 A max. @ Io max. and Vin = 0 - 75 V Input reflected ripple (See Note 6) 5 mA pk-pk Active low remote ON/OFF (See Note 7) Logic compatibility ON OFF Open collector ref to -input 1.2 Vdc max. Open circuit Undervoltage lockout 24 Vin: power up 24 Vin: power down 48 Vin: power up 48 Vin: power down 17 V 16 V 34 V 32.5 V Start-up time (See Note 8) Power up Remote ON/OFF 20 ms 20 ms Output Voltage adjustability 60% to 110% Setpoint accuracy ±1.0% Line regulation Low line to high line ±0.5% Load regulation Full load to min. load ±0.10% Minimum load 0% Overshoot At turn on and turn off Undershoot None Ripple and noise 5 Hz - 20 MHz (See Note 1) 3.3 V and 5 V 2 V and 15 V Temperature co-efficient ±0.01% / °C Transient response (See Note 2) ±2.0% max. deviation; 170 µs recovery to within ±1.0% Remote sense 0.5 Vds transmission line drop compensation None 75 mV pk-pk, 20 mV rms 100 mV pk-pk, 30 mV rms GENERAL SPECIFICATIONS Efficiency (See Efficiency Table) Insulation voltage Input/Case Input/Output Output/Case 1500 Vdc 1500 Vdc 1500 Vdc Switching frequency Fixed 500 kHz typ. Approvals and standards (See Note 5) VDE0805, EN60950, IEC950 UL1950, CSA C22.2 No. 950 Case material Aluminum baseplate with plastic case Material flammability UL94V-0 Weight MTBF 2 advancedenergy.com 110 g (3.88 oz) Bellcore 332 MIL-HDBK-217F @ 40 °C C, 100% loaded 1,400,000 hours 580,000 hours min. BXB100 EMC CHARACTERISTICS Conducted emissions (See Note 3) EN55022 (See Note 3) FCC part 15 EN55022, CISPR22 Level A Level A Level A ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating case temperature Non-operating temperature -40 °C to +85 °C -55 °C to +125 °C Altitude Operating Non-operating 10,000 feet max. 40,000 feet max. Vibration 5 - 500 Hz 2.4 G rms (approx.) PROTECTION Short-circuit Continuous, automatic recovery Overvoltage Non-latching Undervoltage Non-latching Thermal 100 °C baseplate, automatic recovery TELECOM SPECIFICATIONS Central office interface A ETS300-132-2 ORDERING INFORMATION OVP Output Voltage Output Current (Min) Output Current (Max) Efficiency (Typical) Line Load 18 - 36 Vdc 14.5 Vdc 12 V 0A 8.33 A 85% ±0.05% ±0.1% 36 - 75 Vdc 6.5 Vdc 5V 0A 20 A 83% ±0.05% ±0.1% 36 - 75 Vdc 14.5 Vdc 12 V 0A 8.33 A 86% ±0.05% ±0.1% Model Number Output Power (Max.) Input Voltage BXB100-24S12FLTJ 100 W BXB100-48S05FLTJ 100 W BXB100-48S12FLTJ 100 W Regulation Notes: 1. Measured with 10 μF tantalum capacitor and 1 μF ceramic capacitor across output. 2. di/dt = 0.1 A/1 μs, Vin = 48 Vdc, Tc = 25 °C, load change = 0.5 lo max. to 0.75 lo max. and 0.75 Io max. to 0.5 Io max. 3. Units should be characterised within systems. External components required. 4. Input fusing is recommended based on surge current and maximum input current. 5. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 6. Simulated source impedance of 12 μH. 12 μH inductor in series with +Vin. 7. Active high remote on/off option is available (standard product is active low), designate with the suffix ‘FHT’ e.g. BXB100-48S05FHTJ. Consult factory for further details and options. 8. Start-up into resistive load. 9. “J” suffix designation for RoHS 6/6. advancedenergy.com 3 BXB100 EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown. 8 TRIM UP RT1 OR RT2 7 TRIM DOWN 6 MECHANICAL DIMENSIONS VIEW SHOWN PIN SIDE UP 1.90 (48.26) VI(+) Vo (-) +SEN TRIM -SEN 1.400 (35.56) ON/OFF 0.400 (10.16) 0.190 (4.83) 0.010 (0.25) 0.700 (17.77) 0.400 (10.16) 1.000 (25.40) 2.000 (50.80) 2.40 (60.96) Max. 1.400 (35.56) Vo(+) 1.000 (25.40) CASE VI (-) 0.500 (12.69) 0.010 (0.25) 0.200 (5.08) Min. Length for all Input and Output Pins 7 x Ø.040 (1.02) 0.002 (0.05) 0.190 (4.83) 0.010 (0.25) 2.28 (57.91) Max. 2 x Ø.080 (2.03) 0.002 (0.05) 4 x M3 x 0.5 Through ALL DIMENSIONS IN INCHES (mm) Tolerance : x.xx 0.02in. (0.51mm) x.xxx 0.010in. (0.254mm) Pin Connections Pin Function 1 +Vin 2 Remote ON/OFF 3 Case 4 -Vin 5 -Vout 6 -Sense 7 Trim 8 +Sense 9 +Vout 4 advancedenergy.com 0.500 (12.70) ABOUT ADVANCED ENERGY Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. For international contact information, visit advancedenergy.com. powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 Specifications are subject to change without notice. Not responsible for errors or omissions. ©2020 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks of Advanced Energy Industries, Inc. ENG-BXB100-235-01 11.25