DS1200-3-002

ARTESYN DS1200 1200 Watts Distributed Power System Advanced Energy's Artesyn DS1200 series is Artesyn Embedded Power' highest power, highest density bulk front end AC-DC power supply in the industry standard 1U x 2U form factor. It accepts a wide range 90–264 Vac input and provides a main 12 V output plus a 3.3 V or optional 5.5 V standby output. Rated at 1,100 watts, it has a high half-load efficiency of 91%. Housed in an industry standard 1U x 2U rack-mounting package, the power supply is designed for servers and similar space-constrained applications. This series comes in two airflow versions – dc-connector to ac-connector and vice versa. SPECIAL FEATURES  Active power factor correction  EN61000-3-2 harmonic compliance  Active AC inrush control  1U X 2U form factor  21.71 W/in 3  +12 Vdc Output Distributed Power Bulk Front-End Total Output Power: 1200 Watts +3.3 Vdc Stand-by Output Wide Range Input Voltage: 90 - 264 Vac  EEPROM for FRU data  Red/green bi-color LED status  Internal fan speed control  Fan Fail Tach Output Signal  Full digital control  Two year warranty  +3.3 Vdc or +5.0 Vdc stand-by SAFETY  No minimum load required  UL/cUL 60950 (UL Recognized)  Hot plug operation  NEMKO+ CB Report EN60950  N + 1 redundant  EN60950  Internal OR’ing fets  CE Mark  Active current sharing (10 - 100%  China CCC load) DATA SHEET  Built-in cooling fan (40 mm x 28 mm) 2  I C communication interface bus  PMBus compliant ©2020 Advanced Energy Industries, Inc. DS1200 ELECTRICAL SPECIFICATIONS Input Input range: 180 - 264 (1200 W) 90 - 264 (1000 W) Frequency: 47-63 Hz, single phase AC Inrush current: 40 Apk maximum inrush current Efficiency: > 91% typical at high line 50% load Conducted EMI: FCC Subpart J EN55022 Class B Radiated EMI: FCC Subpart J EN55022 Class B Power factor: 0.99 typical Leakage current: 1.40 mA @ 240 VAC Hold up time: 12 ms minimum Output Main DC voltage: +12 V @ 100 A (high line) +12 V @ 81.6 A (low line) Stand-By: +3.3 Vsb @ 6 A (5 V @ 4 A available) Adjustment range: ±5% on +12V only using I2C Regulation: +12 Vdc; +5%/-5% +3.3 Vsb; +5%/-5% Over current: +12 Vdc; latches off if overcurrent lasts over 1 second, otherwise it is auto recovery (See Table 1 next page) +3.3 Vsb, 9 A max (hiccup mode) Over voltage: +12 Vdc; 13.2 - 14.4 Vdc +3.3 Vsb; 3.76 - 4.30 Vdc Under voltage: +12 Vdc; 9 - 10.8 V (latch off) Turn-on delay: 2 second max, 5 - 50 mS, monotonic rise Main output rise time: 5 - 50 mS, monotonic rise LOGIC CONTROL PS_SEATED (A4): TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed PWR GOOD (C3): Active TTL high when output is within regulation limits. AC OK (B1): A low logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5mS early warning signal before 12.0 V DC output loss of regulation. PS_INHIBIT/PS_KILL (B4): When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. PS ON (A1): The output will be enabled when this signal is pulled low, below 0.8 V outputs disabled when pin is driven high or left open. 2 advancedenergy.com DS1200 ENVIRONMENTAL SPECIFICATIONS Operating temperature: -10° to 50 °C Storage temperature: -40 °C to +85 °C Altitude, operating: 10,000 ft Electromagnetic susceptibility/Input transients: -EN61000-3-2, -3-3 -EN61000-4-2, 4.3, 4-4, -4-5, 4-11 -EN55024:1998 RoHS & lead-free compliant: No tantalum caps. Humidity: 20 to 90% RH, non-condensing Shock and vibration specificatons: Complies with standard operating/non-operating random shock and vibration MTBF (Demonstrated): 500K Hrs at full load, 25 °C ORDERING INFORMATION Model Number Nominal Output Voltage Set Point Set Point Tolerance Total Regulation Minimum Current Maximum Current Output Ripple P/P Over Current Stand-by Air Flow DS1200-3 12.0 Vdc ±0.2% ±5% 0A 100 A 120 mV 118 A - 147.6 A* 3.3 V @ 6 A STD DS1200-3-002 12.0 Vdc ±0.2% ±5% 0A 100 A 120 mV 118 A - 147.6 A* 5.0 V @ 4 A STD DS1200-3-003** 12.0 Vdc ±0.2% ±5% 0A 100 A 120 mV 118 A - 147.6 A* 3.3 V @ 6 A REV DS1200-3-004** 12.0 Vdc ±0.2% ±5% 0A 100 A 120 mV 118 A - 147.6 A* 5.0 V @ 4 A REV *Over current latches off if overcurrent lasts over 1 seconds, otherwise it is auto recovery. Derating may apply. advancedenergy.com 3 DS1200 MECHANICAL DRAWING Condition LED Status Stand-by - ON; Main output - OFF; AC PRESENT Blinking green Stand-by - ON; Main output - ON; Solid green Main output OCP, UVP, OVP Blinking Amber FAN_FAULT; OTP; Stand-by OCP/UVP Amber 4 advancedenergy.com DS1200 DC OUTPUT CONNECTOR PINOUT ASSIGNMENT Male connector as viewed from the rear of the supply: D1 D2 D3 D4 D5 D6 C1 C2 C3 C4 C5 C6 B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 PB1 PB2 PB3 PB4 PB5 PB6 P1 - POWER SUPPLY SIDE 1 FCI Power Blade 51721 series 51721-10002406AA 2 Molex Power Connector SD-87667 series 87667-7002 MATING CONNECTOR (SYSTEM SIDE) 1 FCI Power Blade 51741-10002406CC Strait Pins 2 FCI Power Blade 51761-10002406AA Right Angle advancedenergy.com 5 DS1200 PIN ASSIGNMENTS Pin Signal Name PB 1 Main output return PB 2 Main output return PB 3 Main output return PB 4 + Main output PB 5 + Main output PB 6 + Main output A1 PS_ON A2 Main output remote sense return A3 Spare A4 PS_SEATED (Power Supply Seated) A5 STAND-BY A6 STAND-BY RETURN B1 AC_OK (AC Input Present) B2 Main output remote sense B3 Main output current share B4 PS_INHIBIT/PS_Kill B5 STAND-BY B6 STAND-BY RETURN C1 SDA (I C Data Signal) 2 2 C2 SCL (I C Clock Signal)* C3 POWER GOOD C4 Spare C5 STAND-BY C6 STAND-BY RETURN D1 A0 (I C Address BIT 0 Signal) D2 A1 (I C Address BIT 1 Signal) D3 S_INT (Alarm) D4 STAND-BY RMT SENSE D5 STAND-BY D6 STAND-BY RETURN *Supports I 2C standard mode (100 kHz) only 6 advancedenergy.com 2 2 ABOUT ADVANCED ENERGY Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. For international contact information, visit advancedenergy.com. powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 Specifications are subject to change without notice. Not responsible for errors or omissions. ©2020 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks of Advanced Energy Industries, Inc. ENG-DS1200-235-01 12.21