DS850-3-002

ARTESYN DS650/DS850 Distributed Power Bulk Front-End Advanced Energy's Artesyn DS650 and DS850 series of bulk front end AC-DC power supplies offers a compact 1U x 2U solution for systems with distributed power architectures. Rated at 650 and 850 watts respectively, the power supplies provide a choice of 12 V, 24 V or 48 V output. Each model also provides a 3.3 V or optional 5.5 V standby output. DS650 and DS850 series power supplies accept a wide 90–264 Vac input and have a typical conversion efficiency of 82%. Standard features include active current sharing, internal ORing FETs and an EEPROM for storing service data to facilitate efficient field replacement. An I2C communication interface is provided for the FRU EEPROM data. SPECIAL FEATURES  Active power factor correction  EN61000-3-2 harmonic compliance  Inrush control  1U X 2U form factor  15.4 W/ in DATA SHEET Total Input 650/850 Watts Power: +3.3 Vdc Standby Output Wide Range 90 - 264 Vac Output Voltage: 12, 24 and 48 V  EEPROM for FRU data  Amber/Green bi-color LED status  Internal fan speed control  Fan Fail Tach output signal  One year warranty 3  12 Vdc, 24 Vdc and 48 Vdc output  Available in +3.3 V and +5.0 V standby output versions  No minimum load required  Hot plug operation  N + 1 redundant  Internal OR’ing fets SAFETY  UL/cUL 60950 (UL Recognized)  NEMKO+ CB Report EN60950  EN60950  CE Mark  China CCC  Active current sharing (10 - 100% load)  Built-in cooling fans (40 mm x 28 mm) 2  I C communication interface bus ©2020 Advanced Energy Industries, Inc. DS650/DS850 ELECTRICAL SPECIFICATIONS Input Input ra­nge 90 - 264 Vac (wide range) Frequency 47 - 63 Hz, single phase AC Inrush current 55 A maximum inrush current Efficiency > 82% typical at full load, high line Conducted EMI FCC Subpart J EN55022 Class B Radiated EMI FCC Subpart J EN55022 Class B Power factor 0.99 typical Leakage current 1.40 mA @ 240 Vac Hold up time 20 ms minimum Output Main DC voltage +12 V @ 52.5 A/70.0 A +24 V @ 26.3 A/35.0 A +48 V @ 13.1 A/17.5 A Standby +3.3 vsb @ 6 A (5 V @ 4 A available) Adjustment range Factory Set, no pot adjustments Regulation Main output; +5%/-5% +3.3 vsb; +5%/-5% Overcurrent 110% - 150% of nominal Latches off if overcurrent lasts over 1 second, otherwise it is auto recovery. +3.3 vsb, 9 A max (hiccup mode) Overvoltage 110% - 120% of nominal +3.3 vsb; 3.76 - 4.30 Vdc Undervoltage 75% - 90% of nominal Turn-on delay 2 Second max, 5 - 50 mS, Monotonic Rise Main output rise time 5 - 50 mS, Monotonic Rise LOGIC CONTROL PS_SEATED TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed. PWR GOOD Active TTL HiIGH when output is within regulation limits. AC OK A LOW logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5mS early warningsignal before main output loss of regulation. Temp OK A TTL logic HIGH, when operating within allowable temperature range. PS_INHIBIT/PS_KILL This signal is connected to a short pin on the PSU When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. 2 advancedenergy.com DS650/DS850 ENVIRONMENTAL SPECIFICATIONS Operating temperature: 0 to 50 °C, unimpeded airflow Storage temperature: -40 °C to +85 °C Altitude, operating 10,000ft. Electromagnetic susceptibility/Input transients: -EN61000-3-2, -3-3 -EN61000-4-2, 4.3, 4-4, -4-5, 4-11 -EN55024: 1998 RoHS & lead-free compliant (no tantalum caps.) Humidity: 20 to 90% RH, non-condensing Shock and vibration specificatons complies with Astec Std. Specifications. MTBF (Demonstrated) 500K Hrs at full load, 40 °C ORDERING INFORMATION Output Nominal Output Voltage Set Point Set Point Tolerance** Total Regulation Minimum Current Maximum Current Output Ripple P/P DS650-3 12.0 Vdc 3.3 vsb* ±0.2% ±1% ±5% ±5% 0A 0A 52.5 A 6.0 A 120 mV 50 mV DS650-5 24.0 Vdc 3.3 vsb* ±0.2% ±1% ±5% ±5% 0A 0A 26.3 A 6.0 A 240 mV 50 mV DS650-9 48.0 Vdc 3.3 vsb* ±0.2% ±1% ±5% ±5% 0A 0A 13.1 A 6.0 A 480 mV 50 mV DS850-3 12.0 Vdc 3.3 vsb* ±0.2% ±1% ±5% ±5% 0A 0A 70.0 A 6.0 A 120 mV 50 mV DS850-5 24.0 Vdc 3.3 vsb* ±0.2% ±1% ±5% ±5% 0A 0A 35.0 A 6.0 A 240 mV 50 mV DS850-9 48.0 Vdc 3.3 vsb* ±0.2% ±1% ±5% ±5% 0A 0A 17.5 A 6.0 A 480 mV 50 mV *For 5 vsb, please contact marketing department. **Set point tolerance is measured at nominal voltage, 50% load and room temperature. advancedenergy.com 3 DS650/DS850 MECHANICAL DRAWING Power Supply Condition LED Green/Amber No AC power to all PSU OFF AC present/Standby outpus ON, Main output OFF Blinking Green Power supply DC outputs ON and OK Solid Green Main output failure (OCP, OVP, UVP) Blinking Amber Fan Fail, OTP, Standby output OCP/UVP Solid Amber 4 advancedenergy.com DS650/DS850 DC OUTPUT CONNECTOR PINOUT ASSIGNMENT Male connector as viewed from the rear of the supply: D1 D2 D3 D4 D5 D6 C1 C2 C3 C4 C5 C6 B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 PB1 PB2 PB3 PB4 PB5 PB6 P1 - POWER SUPPLY SIDE 1 FCI Power Blade 51721 series 51721-10002406AA 2 Molex Power Connector SD-87667 series 87667-7002 MATING CONNECTOR (SYSTEM SIDE) 1 FCI Power Blade 51741-10002406CC Strait Pins 2 FCI Power Blade 51761-10002406AA Right Angle advancedenergy.com 5 DS650/DS850 PIN ASSIGNMENTS Pin Signal Name PB 1 MAIN O/P RETURN PB 2 MAIN O/P RETURN PB 3 MAIN O/P RETURN PB 4 + MAIN O/P PB 5 + MAIN O/P PB 6 + MAIN O/P A1 PS_ON A2 MAIN O/P V RMT SENSE RETURN A3 TEMP_OK A4 PS_SEATED ( Power Supply Seated) A5 +3V3 STAND-BY A6 +3V3SB RETURN B1 AC_OK (AC Input Present) B2 MAIN O/P RMT SENSE B3 MAIN O/P CURRENT SHARE B4 PS_INHIBIT B5 +3V3 STAND-BY B6 +3V3SB RETURN C1 SDA (I C Data Signal) 2 2 C2 SCL (I C Clock Signal)* C3 POWER GOOD C4 FAN FAIL (Fan Fail Signal) C5 +3V3 STAND-BY C6 +3V3SB RETURN D1 A0 (I C Address BIT 0 Signal) D2 A1 (I C Address BIT 1 Signal) D3 S_INT (Alarm) D4 +3V3 STAND-BY RMT SENSE D5 +3V3 STAND-BY D6 +3V3SB RETURN *Supports I 2C standard mode (100 kHz) only 6 advancedenergy.com 2 2 ABOUT ADVANCED ENERGY Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. For international contact information, visit advancedenergy.com. powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 Specifications are subject to change without notice. Not responsible for errors or omissions. ©2020 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks of Advanced Energy Industries, Inc. ENG-DS650/DS850-235-01 12.14