POWER
Intelligent VS Power
Up to 4920 Watts
Data Sheet
Total Power: Up to 4920 W
Input Voltage: 85 - 264 Vac
380, 440 Vac
120 - 300 Vdc
1-Phase
3-Phase
# of Outputs: Up to 24
TM
Font: Minion Bold for VS
Minion italic for i ; size for each is the same
Created on Mac
Special features
Full medical EN60601 approval*
Intelligent I2C control
Voltage adjustment on all outputs
(manual or I2C)
Configurable input and output OK
signals and indicators
Configurable inhibit/enable
Configurable output UP/DOWN
sequencing
High power density (12 W/cu-in)
Intelligent fan (speed control/fault
status)
uP controlled PFC input with active
Inrush protection
I2C monitor of voltage, current, and
temperature
Programmable voltage, current limit,
inhibit/enable through I2C
Optional extended hold-up module
(SEMI F47 compliance)
Increased power density to 150%
Optional conformal coating
Industrial temp range (-40 ºC to 70 ºC)
Uses standard iMP modules
Field upgradeable firmware
RoHS compliant
SAFETY
UL UL60950/UL2601
CSA
CSA22.2 No. 234 Level 5
UV EN60950/EN60601-1
BABT
Compliance to EN60950/
EN60601 BS7002
CB
Certificate and report
CE
Mark to LVD
* Note: iVS8H does not have Medical or MOPP approvals.
Electrical Specifications
Input
Input range
iVS1 & iVS3
90 - 264 Vac 1Ø; 120 - 300 Vdc
iVS6 & iVS8
170 - 264 Vac 3Ø
iVS8H
396 - 480 Vac rated at 4920 W DC output 3Ø
342 - 480 Vac rated at 4200 W DC output 3Ø
Frequency
47 - 440 Hz
Inrush current
40 A peak maximum (soft start)
Efficiency
Up to 85% @ full case load
Power Factor
0.99 typ. meets EN61000-3-2
Turn-on time
AC on 1.5 sec typical, inhibit/enable 150ms typical Programmable;
50 ms internal turn-on delay (Dual Output only)
EMI Filter
CISPR 22/EN55022 Level “B”. Level “A” for iVS8H
Leakage current
500 µA max. @ 240 Vac; 47-63 Hz
Radiated EMI
CISPR 22/EN55022 Level “B”. Level “A” for iVS8H
Holdover storage
10 ms minimum (independent of input Vac) additional 20 mSEC holdover
storage with optional HUP module (SEMI F47 compatible)
AC OK
> 5 ms early warning minutes before outputs lose regulation Full cycle ride thru
(50 Hz). Programmable
Harmonic distortion
Meets EN61000-3-2
Isolation
Meets EN60950 and EN60601
Meets 1 MOPP Primary to ground, 2 MOPP Primary to Secondary*
Global inhibit / enable
TTL, Logic “1” and Logic “0”; configurable
Warranty
3 years
Color: "i" 100% Blue, 50% Magenta,
0% Yellow, 0% Black
"VS" - 100% Black
i VS Data Sheet
Electrical Specifications
Output
Adjustment range*
± 10% minimum all outputs (manual) (full module adjustment range using I2C)
Factory set point accuracy
1%
I C output program accuracy
± 5%
Margining
± 4 - 6% nominal analog (single output module only)
Overall regulation
0.4% or 20 mV max. (1500 W modules 1% max.)
Ripple
RMS: 0.1% or 10 mV, whichever is greater
Pk-Pk: 1.0% or 50 mV, whichever is greater
Bandwidth limited to 20 MHz
Dynamic response
< 2% or 100 mV, with 25% load step
Recovery time
To within 1% in < 300 µsec
Overcurrent protection**
Configurable through I2C (calibration required). Single output module and main output of the dual output module
105 - 120% of rated output current. Aux output of dual output module 105 - 140% of rated output current.
Special programmable OCP delay on 1500 W module from 100 mSec to 25.5 seconds with shutdown features.
Short-circuit protection
Protected for continuous short-circuit.
Recovery is automatic upon removal of short (Shutdown mode on 1500 W module).
Overvoltage protection*
Configurable through I2C
2
Single output module:
2 - 5.5 V 122 - 134%; 6 - 60 V 110 - 120%
Dual output module:
2 - 6 V 122 - 134%; 8 - 28 V 110 - 120%
Triple output module:
110 - 120% of highest voltage rating
Thermal protection*
Configurable through I2C
All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before
shutdown
Remote sense
Up to 0.5 V total drop (not available on triple output module)
Single wire parallel
Current share to within 2% of total rated current
DC OK*
± 5% of nominal. Configurable through I2C
Minimum load
Not required
Housekeeping bias voltage
5 Vdc @1.0 A max. present whenever AC input is applied
Overall Regulation: ± 5%
Ripple and Noise: 150 mV pk-pk, Bandwidth limited to 150 MHz and measured with 10 uF Tantalum capacitor and
0.1 uF ceramic capacitor in parallel on the output.
Module inhibit*
Configured and controlled through I2C
Output/Output isolation
> 1 Megohm, 500 V
* Can be controlled via I C
** Controlled via I2C but requires load calibration (except 1500 W module)
2
Environmental Specifications
Operating temperature
-40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C. (-20 °C start up)
Storage temperature
-40 °C to +85 °C
Electromagnetic susceptibility
Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity
Operating; non-condensing 10% to 95% RH
Vibration
IEC68-2-6 to the levels of IEC721-3-2
MTTF field demonstrated
> 550,000 hours at full load, 220 Vac and 25 °C ambient conditions
i VS Data Sheet
Output Module Line-up
1
2
3
5
4
—
Module Type
Single
Single
Single
Single
Dual
Triple
Max output power
210 W
360 W
750 W
1500 W
144 W
36 W
Max output current
35 A
60 A
150 A
300 A
10 A
2A
2 - 60 V
2 - 60 V
2 - 60 V
2 - 60 V
8 - 15*, 24 - 28; 8 - 15*, 8 - 15*;
8 - 15*, 2 - 6; 2 - 6, 2 - 6; 24 - 28,
24 - 28; 24 - 28, 2 - 6
8 - 15, 8 - 15, 2 - 6; 8 - 15, 8 - 15,
8 - 15; 8 - 15, 8 - 15, 18 - 28; 8 - 15,
18 - 28, 2 - 6
Module Code
Output voltages available*
Standard voltage increments
25
25
25
25
Remote sense
Yes
Yes
Yes
Yes
16
Yes
18
Yes
No
Remote margin
Yes
Yes
Yes
Yes
No
No
No
V-Program - I2C Control
Yes
Yes
Yes
Yes
Yes
Yes
No
Active Current Share
Yes
Yes
Yes
Yes
Yes
No
No
Module Inhibit - I C Control
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Module Inhibit - Analog
Yes
Yes
Yes
Yes
Yes
No
No
Overvoltage/Overcurrent protection
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Minimum load required
No
No
No
No
No
No
No
1
2
3
4
2
Slots occupied in any iVS case
1
1
* Note: Contact Factory for extended range down to 6 V
Internal Part Number Reference Table
Part #
Where X =
Description
Module Code
73-558-XXXXi
0005, 0006, 0012, 0024, 0048, 04XX
iVS/iMP 1500 W Module
5A0 - 5Z0
Single
Dual
210 W
360 W
750 W
1500 W (2.0 - 8.0 V)
144 W
1500 W (10 - 60 V)
Triple
36 W
1500 W with Bus Bar Adaptor Option
(used with the 10 - 60 V module)
i VS Data Sheet
Output Module Voltage/Current*
Voltage
Voltage Code
Single Output Module Code
Dual Output***
Triple Output
1
2
3
5
4
4
-
-
-
I2C Adjustment
Ranges****
2V
A
35 A
60 A
150 A
300 A
10 A
10 A
—
—
2A
1.8 - 2.2
2.2 V
B
35 A
60 A
150 A
300 A
10 A
10 A
—
—
2A
2.0 - 2.4
3V
C
35 A
60 A
150 A
300 A
10 A
10 A
—
—
2A
2.7 - 3.3
3.3 V
D
35 A
60 A
150 A
300 A
10 A
10 A
—
—
2A
3.0 - 3.6
5V
E
35 A
60 A
150 A
300 A
10 A
10 A
—
—
2A
4.5 - 5.5
5.2 V
F
35 A
60 A
144 A
288 A
10 A
10 A
—
—
2A
4.7 - 5.7
5.5 V
G
34 A
58 A
136 A
273 A
10 A
10 A
—
—
2A
5.0 - 6.1
6.0 V
H
23 A
42 A
97.5 A
250 A
10 A*
10 A*
—
—
2A
5.4 - 6.6
8.0 V
I
20 A
36 A
84.4 A
187.5 A
10 A
4A
1A
1A
1A
7.2 - 8.8
10 V
J
18 A
32 A
75 A
140 A
10 A
4A
1A
1A
1A
9.0 - 11.0
11 V
K
17 A
31 A
68 A
136.3 A
10 A
4A
1A
1A
1A
9.9 - 12.1
12 V
L
17 A
30 A
62.5 A
125 A
10 A
4A
1A
1A
1A
10.8 - 13.2
14 V
M
14 A
21 A
53.5 A
107 A
9A
4A
1A
1A
1A
12.6 - 15.4
15 V
N
14 A
20 A
50 A
100 A
8A
4A
1A
1A
1A
13.5 - 16.5
18 V
O
11 A
19 A
41.6 A
83.3 A
—
—
—
0.5 A
0.5 A
16.2 - 19.8
20 V
P
10.5 A
18 A
37.5 A
75 A
—
—
—
0.5 A
0.5 A
18.0 - 22.0
24 V
Q
8.5 A
15 A
30 A
62.5 A
4A
2A
—
0.5 A
0.5 A
21.6 - 26.4
28 V
R
6.7 A
11 A
26.8 A
53.5 A
3A
2A
—
0.5 A
0.5 A
25.2 - 30.8
30 V
S
6.5 A
11 A
25 A
50 A
—
—
—
—
—
27.0 - 33.0
33 V
T
6.2 A
10.9 A
22.7 A
35.8 A
—
—
—
—
—
29.7 - 36.3
36 V
U
5.8 A
10 A
20.8 A
35.8 A
—
—
—
—
—
32.4 - 39.6
42 V
V
4.2 A
7.5 A
16 A
35.7 A
—
—
—
—
—
37.8 - 46.2
48 V
W
4.0 A
7.5 A
15.6 A
31.2 A
—
—
—
—
—
43.2 - 52.8
54 V
X
3.7 A
6.0 A
13.9 A
27.7 A
—
—
—
—
—
48.6 - 59.4
60 V
Y
3.5 A
6.0 A
12.5 A
25 A
—
—
—
—
—
54.0 - 66.0
Special*
Z
35 A
60 A
150 A
300 A
—
10 A
2.3 - 2.6
Special*
Z
35 A
60 A
150 A
300 A
—
10 A
3.7 - 4.4
Special*
Z
20 A
36 A
80 A
140 A
—
8A
6.7 - 7.1
Contact Factory
* Note: Contact Factory for extended range down to 6 V.
** Increments of current not shown can be achieved by paralleling modules (add currents of each
module selected).
*** Total output power on dual model must not exceed 144 W.
**** For single output modules only.
Green reference lines indicate physical module groupings
Ordering Information
Sample below is 3210 W case with 12 V @ 125 A; 24 V @ 8.5 A; 5 V @ 60 A; 12 V @ 10 A and 12 V @ 4 A; with no options.
Case Size
Module/Voltage/Option Codes
First - Module Code
Second - Voltage Code
Third - Option Code
iVS1
- 5L1 - 1Q1 - 2EO - 4LL0 -
Case Size (mm)
1-Phase Input
1 = 5” x 5” x 11”; 1500 W - 3210 W, 9 Slots
(127 x 127 x 279.4 mm)
3 = 5” x 8” x 11”; 1800 W - 4500 W, 14 Slots
(127 x 203.2 x 279.4 mm)
3-Phase Input
6 = 5” x 5” x 11”; 3120 W, 9 Slots
(127 x 127 x 279.4)
8, 8H = 5” x 8” x 11”; 4920 W, 14 Slots
(127 x 203.2 x 279.4 mm)
Module Codes:
(None) = 36 W triple O/P (1 slot)
1 = 210 W single O/P (1 slot)
2 = 360 W single O/P (2 slot)
3 = 750 W single O/P (3 slot)
5 = 1500 W single O/P (slot 4)
4 = 144 W dual O/P (1 slot)
HUP = Extra 30mS hold-up (1 slot)
Voltage Codes:
See Output Module Voltage/Current table
Option Codes:
0 = Standard
1 = Module enable
2 = Constant current
3 = 1 & 2 combined
4 = Set for use in standard (non-intelligent case)
5 = Shutdown mode for 1500 W
6 = 1 & 5 combined
7-9 Future
Ordering Note:
1. USB to I2C module order code 73-769-001
Software Code
Case Option Codes
00
First Digit
0 - 9, A - Z Parallel code
(See parallel codes table below)
Second Digit
0 = No options
1 = Reverse air
2 = Not used
3 = Global enable
4 = Fan Idle w/inhibit
5 = Opt 1 + Opt 3
6 = Opt 1 + Opt 4
7 = Opt 3 + Opt 4
8 = Opt 1 + 3 + 4
9 = RS485
73-544-001
B = USB
73-546-001
C=9+3
D = CANBUS 73-544-004
E=D+3
F = RS485 - MODBUS 73-544-005
-
A
Software code used
for configuration
change. “A” is
standard
Hardware Code
-
###
Factory assembled
for hardware of
firmware mods.
i VS Data Sheet
Ordering Information
Parallel
Code
Slot No.
1
1&2
iVS1, 6
Diagram
AC 9 8 7 6
210 210; 210 144; 144 144
2&3
AC 9 8 7 6
360 360; 360 210; 360 144; + above
5 4 3 2 1
3
3&4
AC 9 8 7 6
5 4 3 2 1
4
4&5
AC 9 8 7 6
5 4 3 2 1
5
3, 4, & 5
AC 9 8 7 6
5 4 3 2 1
6
iVS1,6: 4 & 6
AC 9 8 7 6
Diagram
AC 14 13 12 11 10 9
Possible Configurations
210 210; 210 144; 144 144
8 7 6 5 4 3 2 1
5 4 3 2 1
2
iVS3, 8H
Possible Configurations
AC 14 13 12 11 10 9
360 360; 360 210; 360 144; + above
8 7 6 5 4 3 2 1
750 360; 750 210; 750 144; 210 210;
210 144; 144 144
1500 210; 1500 144; 210 210; 210 144;
144 144; 360 210; 360 144
750 210 210; 750 210 144; 750 144
144
AC 14 13 12 11 10 9
8 7 6 5 4 3 2 1
AC 14 13 12 11 10 9
8 7 6 5 4 3 2 1
AC 14 13 12 11 10 9
750 750; 750 360; 750 210; 750 144;
210 210; 210 144; 144 144
1500 1500; 1500 750; 1500 360; 1500 210;
1500 144; 210 210; 210 144; 144 144; 360 360;
360 210; 360 144
750 210 210; 750 210 144; 750 144 144
8 7 6 5 4 3 2 1
1500 1500; 1500 750
5 4 3 2 1
7
4, 5, & 6
AC 9 8 7 6
5 4 3 2 1
8
9
A
C
E
F
G
iVS1, 6: 3 & 6
iVS3,8: 4, 5, & 9
AC 9 8 7 6
iVS1,6: 1 & 6
iVS3, 8: 4, 5 & 9; 12 & 13
AC 9 8 7 6
iVS1,6: 3 & 4; 8 & 9
iVS3, 8: 4 & 5; 11 & 12
AC 9 8 7 6
iVS1,6: 3, 4 & 6
iVS3, 8: 6 & 7; 3, 4, 11 & 12
AC 9 8 7 6
iVS1,6: 3, 4, 6; 8 & 9
iVS3, 8: 3, 4, 11, & 12
AC 9 8 7 6
iVS1,6: 7-8
iVS3, 8: 3 & 4; 11 & 12
AC 9 8 7 6
iVS3, 8: 3,4 & 9
1500 210 210; 1500 210 144;
1500 144 144; 1500 210 1500
750 750
AC
14 13 12 11 10 9
8 7 6 5 4 3 2 1
5 4 3 2 1
1500 1500; 1500 360; 1500 144
5 4 3 2 1
AC 14 13 12 11 10 9
8 7 6 5 4 3 2 1
750 210 & 750 210
5 4 3 2 1
1500 210 210; 1500 210 144; 1500 144 144
AC 14 13 12 11 10 9
1500 1500 1500; 1500 1500 750; 1500 1500 360;
1500 1500 210; 1500 1500 144
1500 1500 1500 360; 1500 1500 1500 210;
1500 1500 1500 144
1500 1500 & 750 750
8 7 6 5 4 3 2 1
750, 360, 750
AC 14 13 12 11 10 9
750 750 360 750 750
8 7 6 5 4 3 2 1
5 4 3 2 1
750, 360, 750, 210
AC 14 13 12 11 10 9
750 750 750 750
8 7 6 5 4 3 2 1
5 4 3 2 1
5 4 3 2 1
AC 14 13 12 11 10 9
8 7 6 5 4 3 2 1
360, 360
AC 14 13 12 11 10 9
750 360 & 750 210; 750 750 & 750 750
8 7 6 5 4 3 2 1
AC 14 13 12 11 10 9
750 750 750
8 7 6 5 4 3 2 1
H
iVS3, 8: 11 & 12
AC 14 13 12 11 10 9
750 750
8 7 6 5 4 3 2 1
J
iVS3, 8: 4 & 5; 9 & 10
AC 14 13 12 11 10 9
1500 210 & 210 1500
8 7 6 5 4 3 2 1
K
iVS3, 8: 1 & 9; 5 & 12
AC 14 13 12 11 10 9
1500 750 & 1500 750
8 7 6 5 4 3 2 1
L
iVS3, 8: 3 & 4; 7 & 8; 9 & 10
AC 14 13 12 11 10 9
750 210 & 750 210 & 210 1500
8 7 6 5 4 3 2 1
M
iVS3, 8: 3, 4 & 9; 6 & 7
AC 14 13 12 11 10 9
750 750 360 750
8 7 6 5 4 3 2 1
N
iVS3, 8: 4, 5 & 9; 12,13 & 14
AC 14 13 12 11 10 9
1500, 1500, 1500, 210, 210
8 7 6 5 4 3 2 1
P
iVS3, 8: 1 & 9
AC 14 13 12 11 10 9
8 7 6 5 4 3 2 1
1500, 750
i VS Data Sheet
i VS Case Specifications
iVS1 and iVS6
S
L
O
T
5
S
L
O
T
9
S
L
O
T
8
S
L
O
T
7
S
L
O
T
6
S
L
O
T
4
S
L
O
T
3
S
L
O
T
2
S
L
O
T
1
Input
90 - 264 Vac
iVS1 = 5” x 5” x 11”
1500 W max.
(127 x 127 x 279.4 mm)
9 available slots
iVS6 = 5” x 5” x 11”
N/A
(127 x 127 x 279.4 mm)
9 available slots
3-phase only
iVS3, iVS8 and iVS8H
S
L
O
T
8
S
L
O
T
7
Input
90 - 264 Vac
S
L
O
T
14
S
L
O
T
13
S
L
O
T
12
S
L
O
T
11
S
L
O
T
10
S
L
O
T
9
S
L
O
T
6
S
L
O
T
5
S
L
O
T
4
S
L
O
T
3
S
L
O
T
2
S
L
O
T
1
iVS3 = 5” x 8” x 11”
1800 W max.
(127 x 203.2 x 279.4 mm)
14 available slots
N/A
iVS8 = 5” x 8” x 11”
(127 x 203.2 x 279.4 mm)
14 available slots
N/A
N
iVS8H = 5” x 8” x 11”
1
(127 x 203.2 x 279.4 mm)
2
~
14 available slots
170 - 264 Vac
3210 W max.
170 - 264 Vac
3210 W max.
170 - 264 Vac
4500 W max.
170 - 264 Vac
4920 W max.
380 Vac
440 Vac
4920 W max.
3
Pin Connectors
Figure 1. AC Input
1
2
3
N
~
2
φ1
φ2
3
φ3
1
4
iVS6
iVS1, iVS3
Figure 1. AC Input
Figure 2. Connector J1
AC
Input
Single
Phase
Pin
Function
1
AC neutral
Line 1
2
AC line (hot)
Line 2
3
Chassis (earth)
ground
Not used
Line 3
4
3 Phase
Chassis (earth)
ground
1
6
5
10
Figure 2. Connector J1
Mates with
Molex 90142-0010 Housing
90119-2110 Pin
Connector Kit Part No.:
70-841-004
iVS8, iVS8H
Figure 3. Connector J2
10
6
5
1
Mates with
Landwin 2050S1000 Housing
2053T011V Pin
or
JST PHDR-10VS Housing
JST SPHD-002T-P0.5 (28-24)
JST SPHD-001T-P0.5 (26-22)
Connector Kit Part No.:
70-841-023
I2C Bus Output Connector
Pin
Function
1
2
3
4
5
6
7
8
9
10
No connection
No connection
No connection
Serial clock signal (SCL)
Serial data signal (SDA)
Address bit 0 (A0)
Address bit 1 (A1)
Address bit 2 (A2)
Secondary return (GND)
5 VCC external bus (5 VCC bus)
PFC Input Connector
(control & signals)
Pin
Function
1
2
3
4
5
6
7
8
9
10
Input AC OK - “emitter”
Input AC OK - “collector”
Global DC OK - “emitter”
Global DC OK - “collector”
Spare
Global inhibit/optional enable logic “0”
Global inhibit/optional enable logic “1”
Global inhibit/optional enable return
+5 VSB housekeeping
+5 VSB housekeeping return
i VS Data Sheet
Mechanical Drawings
iMP Modules
Single 210 Watt
DC-DC Converter Output Modules
.44” (11.2)
2X
V+
~
single or dual o/p
single or dual o/p
single or dual o/p main
dual o/p, single is spare
dual o/p, single is spare
M4X8 SCREWS
VV ADJ
.44"
(11.4)
single or dual o/p main
single o/p
single o/p
single or dual o/p main
(12.1)
Function
+ Remote Sense
Remote Margin / V. Program
Margin High
- Remote Sense
N / Margin Low
1
Spare
2
Module, Isolated Inhibit
3 Inhibit Return
Module
Current Share (SWP)
+ Remote Sense V2
Figure Sense
1. AC Input
- Remote
V2
1.38"
(35.1)
Pin No.
1
2
3
4
5
6
7
8
9
10
.48"
Control Signal Information, J1 Control Connector
DC OUTPUT CONNECTOR
.32"
(8.1)
Single 360 Watt
.63”
.33”
(16.0)
(8.5)
* Note: All iMP modules have a green DCOK LED. (except for 36 W module)
.48” (12.1)
(2X)
Mates with
Molex 90142-0010 Housing
90119-2110 Pin
VPIN 1
V ADJ
.44”
(11.4)
5
10
1
6
V+
M 4 X 8 SCREWS
WITH CONICAL
WASHER
1.38” (35.2)
(2X)
Figure 4. Connector J1
PIN 1
Figure 2. Connector J1
DC OUTPUT
CONNECTOR
.32”
(8.1)
Single 750 Watt
Single 1500 Watt 10-60 V
Single 1500 Watt 2-8 V
.63"
(16.0)
V+
59.3 ± 0.2
.59"
(15.0)
(3x) 31.6 ±0.8
03/24/2008
11.3 ±0.8
(2x) 15.0 ±0.8
DC OUTPUT CONNECTOR
(2x) 16.0 ±0.2
PIN 1
(2x) 16.0 ±0.2
For Factory-Use Only
.44"
(11.0)
1.24"(31.5)
(2X)
.61"(15.6)
(2X)
8.1 ±0.8
M4X8 SCREWS W/
CONICAL WASHER (6X)
VADJ
V-
.32"
(8.1)
PIN 1
V ADJ
M4X8 SCREWS
(4X)
DC OUTPUT
CONNECTOR
V-
V+
Dual 144 Watt
Triple 36 Watt
.46 (11.7)
V1 +
(4X)
V1 -
V1 +
V1 -
V2 +
V2 +
V2 -
V2 -
.30 (7.5)(3X)
M3X8 SCREWS WITH SPRING WASHER
(4X)
1.17 (29.7)
.42 (10.7)
.32
(8.1)
V2 ADJ
V1 ADJ
PIN 1
V3 +
V3 -
Mates with
Molex 09-91-0600 Housing
26-60-5060 Pin
i VS Data Sheet
i VS Series
iVS1 (1500/3210 Watts Max)
5-Inch Case Size: iVS1: 5” x 5” x 11” (127 mm x 127 mm x 279.4 mm)
Weight: iVS1 Case: 6.2 lbs. • 1500 W Single: 2.0 lbs. • 750 W Single: 1.6 lbs.
• 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb.
REVERSE AIRFLOW DIRECTION
NORMAL AIRFLOW DIRECTION
127.0 ± 0.5
B
B
A
279.40 ± 1.27
127.0 ± 0.5
63.5
AC INPUT
CONNECTOR
FAN
92 X 92 X 38 mm
L
N
PE
127.0 ± 0.9
127.0 ± 0.9
101.6 ± 0.9
C
USB PROGRAMMING
CONNECTOR OPTION
65.5
SELV CONTROL
CONNECTOR
I2C
C
CONNECTOR
12.7
OUTPUT MODULE
AREA
19.1
171.5
M4 MTG HOLES 4 PL
11.6
AC OK
LED
DC OK
LED
13.5
33.5
12.0
57.4
“MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES”
171.45
29.05
5.00
12.70
B
114.30
22.80
19.05
171.45
A
Notes:
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes
mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
C
i VS Data Sheet
i VS Series
iVS3 (1800/4500 Watts Max)
8-Inch Case Size: iVS3: 5” x 8” x 11” (127 mm x 203.2 mm x 279.4 mm)
Weight: iVS3 Case: 9.0 lbs. • 1500 W Single 2.0 lbs.• 750 W Single: 1.6 lbs.
• 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb.
REVERSE AIRFLOW DIRECTION
NORMAL AIRFLOW DIRECTION
B
203.2±0.5
279.4±1.27
52.6
A
12.7
USB PROGRAMMING
CONNECTOR OPTION
I2C
1
3
SL
O
T
2
T
O
SL
T
T
O
SL
O
SL
T
O
SL
4
5
7
6
T
O
SL
8
T
T
O
O
SL
171.45
A
11.6
SELV CONTROL
CONNECTOR
C
C
DC OK LED
42
M4 MTG HOLES 4 PL
AC OK LED
61.2
19.1
81.5
29.1
#8-32 MTG HOLES
5PL
MARKED “A”
6, 7 REF
171.5
B
A
B
A
B
A
B
B
A
177.8
149.4
173.3
12.7
14.4
“MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES
B
A
16.2
19.1
171.5
M4 MTG
HOLES
5 PL
MARKED “B”
A
Notes:
1. Input: Barrier type. Three M4 screws (0.512” centers). Max torque: 7 in-lbs. (0.79 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes
mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
65.5
127±0.9
101.6 ± 0.9
SL
OUTPUT MODULE
AREA
SL
FAN
80 X 80 X 38mm
O
T
9
11
10
O
O
SL
SL
98
A
T
T
12
T
O
SL
SL
SL
O
O
T
AC INPUT
CONNECTOR
T
14
13
B
C
i VS Data Sheet
i VS Series
iVS6 (3210 Watts Max)
5-Inch Case Size: iVS6: 5” x 5” x 11” (127 mm x 127 mm x 279.4 mm)
Weight: iVS6 Case: 6.0 lbs. • 1500 W Single 2.0 lbs. • 750 W Single: 1.6 lbs.
• 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb.
279.4±1.0
5.0±0.5
NORMAL AIRFLOW DIRECTION
REVERSE AIRFLOW DIRECTION
293.0±1.2
57.4
171.5 (2X)
SLOT 7
SLOT 9
SLOT 6
101.6±0.9 (2X)
SLOT 1
SLOT 3
SLOT 2
12.7 (2X)
171.5 (2X)
SLOT 4
12.7 (2X)
FOR M4 SCREW (4X)
(FOR SYSTEM MOUNTING)
19.1 (2X)
171.5 (2X)
19.1 (2X)
12.0
19.1 (2X)
12.7 (4X)
33.5
DC OK
LED
11.6
(2X)
SELV CONTROL
CONNECTOR 13.5
SLOT 5
101.6±0.9 (2X)
65.5
127.0±0.9
AC OK
LED
I2C CONNEC-
L1
L2
L3
L1 L2 L3
INTERNAL FUSES
15A/250V
USB PROGRAMMING
CONNECTOR
12.6±0.6
AC INPUT
CONNECTOR
SLOT 8
GND
20.3±0.6
127.0±0.5
63.5
12.7 (4X)
FOR #8-32 SCREW (4X)
(SYSTEM MOUNTING)
FOR M4 SCREW (4X)
(FOR SYSTEM MOUNTING)
171.5 (2X)
29.1 (2X)
Notes:
1. Input: Barrier type. Four M3 screws (0.325” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series).
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with
2053T011P (Landwin) pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
FOR M4 SCREW (4X)
(FOR SYSTEM MOUNTING)
i VS Data Sheet
i VS Series
iVS8 (4920 Watts Max)
iVS8H (4920 Watts Max)
8-Inch Case Size: iVS8: 5” x 8” x 11” (127 mm x 203.2 mm x 279.4 mm)
Weight: iVS8 Case: 9.0 lbs. • 1500 W Single 2.0 lbs. • 750 W Single: 1.6 lbs.
• 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb.
6.8 max
(2x)
NORMAL AIRFLOW DIRECTION
REVERSE AIRFLOW DIRECTION
291.1±1.2
279.4±0.2
USB Programming
Connector Option
50.7
72.1
7
12.7 (2x)
31.8
19.1 (2x)
MOSYTEM Mounting for
#8-32 Screw (5X) (’a’)
19.1 (2x)
171.5 (2x)
171.5 (2x)
171.5 (2x)
19.1 (3x)
14.4 (2x)
12.7 (2x)
SELV Control
Connector
GND
Terminal
15.5 (2x)
23.9 (2x)
MOSYTEM Mounting
for M4 Screw (I3X) (’a’)
I2C Connector
101.6±0.9
12.7 (2x)
11.6 (2x)
65.5 (2x)
127.0±0.2
AC Input
Connector
101.6±0.9
12.7 (2x)
203.2±0.2
155.6
52.6
29.1 (3x)
171.5 (2x)
Notes:
1. Input: Barrier type. Three M3.5 screws (0.394” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series).
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with
2053T011P (Landwin) pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
i VS Data Sheet
Optional CANBUS or RS485 Interface
The RS485/CAN-to-I2C uses 2 Input Protocols and 1
Output Protocol.
Slave/Server Device(s)
The Input Protocols used are RS485 using Modbus
(Command Index: 0x01), and CAN using modified Modus
(Command Index: 0x02).
Adapter
Output Protocols
I2C with SMBus
Support
The Output Protocol use is: I2C with SMBus support
(Command Index: 0x80).
Adapter Protocol
Adapter Command
Adapter Controls
Input Protocols
RS485 using
Modbus
CAN using
Modified Modbus
Master/Client Device(s)
RS485/CAN - to - I2C
For detailed info, download the Software Requirements
Specification (SRS) from http://www.artesyn.com/
power/power-supplies/category.php?catID=103
iVS CAN RS485
iVS I2C USB
WORLDWIDE OFFICES
Americas
Europe (UK)
Asia (HK)
2900 South Diablo Way
Suite B100
Tempe, AZ 85282, USA
+1 888 412 7832
Ground Floor Offices, Barberry House
4 Harbour Buildings, Waterfront West
Brierley Hill, West Midlands
DY5 1LN, UK
+44 (0) 1384 842 211
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
Artesyn Embedded Technologies, Artesyn Embedded Power, Artesyn, and all Artesyn related logos are
trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to
are trade names, trademarks, or registered trademarks of their respective owners. Specifications are subject to
change without notice. © 2020 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms
and conditions, please visit www.artesyn.com/legal.
www.artesyn.com
For more information: www.artesyn.com
For support: productsupport.ep@artesyn.com
iVS DS 09Jun2020
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Artesyn Embedded Technologies:
IVS1-5R0-00-A IVS1-5R0-5R0-60-A
工商网监
湘ICP备2023018690号
