LCM1500W-T-4

ARTESYN LCM1500 1500 Watts Bulk Front End Advanced Energy’s Artesyn LCM1500 series provide for a very wide range of AC-DC embedded power requirement. Featuring high build quality with robust screw terminals, long life, and typical full-load efficiency of greater than 89 percent, these units are ideal for use in industrial and medical applications. They are backed by a comprehensive set of industrial and medical safety approvals and certificates. Variable-speed ‘Smart Fans’ draw on software controls developed by Advanced Energy to match fan speed to the unit’s cooling requirement and load current. Slowing the fan not only saves power but also reduces wear, thus extending its life. SPECIAL FEATURES COMPLIANCE  1500 W output power  EMI Class A  Low cost  EN61000 Immunity  2.5” x 5.2” x 10.0”  RoHS3  12 Watts per cubic inch  Industrial/Medical safety  -40 °C to 70 °C with derating  Optional 5 VDC @ 2 A housekeeping  High efficiency: 89% typical  Variable speed “Smart Fans”  DSP controlled  Conformal coat option  ± 10% adjustment range  Margin programming  OR-ing FET AT A GLANCE Total Power 1500 W # of Outputs Single Outputs 12 to 48 VDC Optional 5 VDC standby SAFETY  UL/cUL Recognized ITE (UL/CSA62368-1)  UL/cUL Recognized Medical (ANSI/AAMI ES60601-1)  TUV-SuD ITE + Medical (EN62368-1 and EN60601-1)  CE LVD (EN62368-1 + RoHS)  BSMI  CB Report  CE and UKCA Mark · through Demko for IEC60950-1 · through TUV-SuD for IEC60601-1 ©2022 Advanced Energy Industries, Inc. LCM1500 ELECTRICAL SPECIFICATIONS Input Input ra­nge 90 to 264 VAC (Operating) 115/230 VAC (Nominal) Terminal Block Frequency 47 to 440 Hz, Nominal 50/60 Input fusing Internal 30 A fuses, both lines fused Inrush current ≤ 25 A peak Power factor 0.99 typical, meets EN61000-3-2 Harmonics Meets IEC 1000-3-2 requirements Input current 18 A RMS max input current, at 100 VAC Hold up time 14 ms minimum for main O/P, at full rated load Efficiency > 89% typical at full load / 230 VAC nominal Leakage current < 400 μA @ 240 VAC for UL test method Isolation voltage PRI-Chassis 2087 VAC Basic PRI-SEC 4000 VAC Reinforced 2xMOPP SEC-Chassis 250 VDC LCM1500Q Efficiency Without the 5 Vsb 92.00 90.00 88.00 Efficiency % 86.00 100 Vac 230 Vac 84.00 82.00 80.00 78.00 76.00 25 50 75 Loading % 2 advancedenergy.com 100 LCM1500 ELECTRICAL SPECIFICATIONS Output Output rating See Ordering Information Table Set point ± 0.5% 230 VAC @ half load Total regulation Main Output: ± 2.0% 5 Vsb: ± 5% Combined line/load/temperature change, warm-up drift when measured at output terminal Rated load 1500 W maximum Derate linear to 50% from 50 °C to 70 °C Minimum load Main Output @ 0A 5 Vsb @ 0A No loss of regulation Output ripple Main Output: 1% max p-p 5 Vsb: 50 mV max p-p Measured with 0.1 μF Ceramic and 10 μF Tantalum Capacitor on any output, 20 MHz No overshoot/undershoot outside the regulation band during on or off cycle Output voltage overshoot Transient response Peak Deviation: ± 4% Setting time < 300 μS Max units in parallel 50% load step @ 1 A/μs Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Up to 4 Remote sense Compensation up to 500 mV Short circuit protection (SCP) Protected, no damage to occur Bounce mode Overcurrent protection (OCP) 105% to 125% 120% to 170% Main output (Bounce mode) 5 Vsb output (Bounce mode) Overvoltage protection (OVP) 125% to 145% 110% to 125% Main output (Latch mode) 5 Vsb output (Latch mode) Overtemperature protection (OTP) 55 °C to 65 °C ambient temperature Shut down and auto-recover ENVIRONMENTAL SPECIFICATIONS Operating temperature range -40 °C to +70 °C linear derating to 50% from 50 °C to 70 °C. For "L" version linear derating starts at 45 °C Storage temperature -40 °C to +85 °C Humidity 10% to 95% Non-operating. 20-90% operating. Conformal coat option available Altitude Operating - 16,404 feet (5000 m) Storage - 30,000 feet (9144 m) Shock MIL-STD-810F 516.5 Procedure I, VI Storage Vibration MIL-STD-810F 514.5 Cat. 4, 10 Storage Fan noise < 45 dBA, 80% load at 30 °C. For the "L" version, the noise is < 61dBA at 80% load at 25 °C advancedenergy.com 3 LCM1500 ORDERING INFORMATION TABLE 1 Nominal Output Voltage Set Point Set Point Tolerance Adjustment Range 12 V 12 V ±0.5% Model Number Output LCM1500L Min Max Output Ripple P/P (0-50 ˚C) 10.8 - 13.2 V 0A 133 A 120 mV 1500 W 2% Current Max Continuous Power Combined Line/ Load Regulation LCM1500N 15 V 15 V ±0.5% 13.5 - 16.5 V 0A 100 A 150 mV 1500 W 2% LCM1500Q 24 V 24 V ±0.5% 21.6 - 26.4 V 0A 67 A 240 mV 1500 W 2% LCM1500R 28 V 28 V ±0.5% 25.2 - 30.8 V 0A 53 A 280 mV 1500 W 2% LCM1500U 36 V 36 V ±0.5% 32.4 - 39.6 V 0A 43 A 360 mV 1500 W 2% LCM1500W 48 V 48 V ±0.5% 43.2 - 52.8 V 0A 33 A 480 mV 1500 W 2% Note: LCM1500Q is 80 PLUS® certified ORDERING INFORMATION TABLE 2 LCMXXXXY - Case Size A Input Termination - B - C - ### Acoustic Noise Option Codes* Hardware Code Blank = Standard Blank = No Options Factory Assigned for Modiefied Standards 1-Phase input where XXXX = 1500 = 2.5” x 5.2” x 10.0”, 1500W T = Terminal Block Voltage Code Y = 1 = Conformal Coat 2 = Reverse Air Code 3 = Opt 1 + 2 L 12 4 = 5V Standby N 15 5 = Opt 1 + 4 Q 24 6 = Opt 2 + 4 R 28 7 = Opt 1 + 2 + 4 U 36 8 = Constant Current W 48 9 = Opt 1 + 8 B = Opt 2 + 8 C = Opt 1 + 2 + 8 D = Opt 4 + 8 E = Opt 1 + 4 + 8 F = Opt 2 + 4 + 8 G = Opt 1 + 2 + 4 + 8 *Note: Some option code combinations may not be configured yet and will require extra leadtime the first time they are requested. 4 advancedenergy.com LCM1500 MECHANICAL DRAWINGS (LCM1500Q-T, LCM1500R-T,LCM1500U-T and LCM1500W-T) Notes: MOUNTING LOCATIONS SCREW PENETRATION DEPTH IS 4.6 mm MAX. RECOMMENDED SCREW TORQUE: M3.5 x 0.6P = 6 - 8kgf-cm M4.0 x 0.7P = 8 - 10kgf-cm Bus bar adapter (option) P/N 500-006848-0000 advancedenergy.com 5 LCM1500 MECHANICAL DRAWINGS (LCM1500L-T and LCM1500N-T) Notes: 1. Parts must be completely assembled. 2. Quality controlled dimensions. These dimensions to be included in the mechanical CPK of 1.33 3. C asing parts used must have matching color. In order to ensure color matching of parts, it is required that the raw material that will be processed by the fabricator will come from the same supplier and the sheetmetal fabricator for all matching parts must be the same. To avoid color variations on the same lot delivered, all parts with matching color requirement should be delivered as a set by the fabricator. 5. S  heared edges visible to the customer should have no rust formation. If rust formation is present then a concealing layer of silver ink or some other substitute should be applied on the rusted area. 6. Mounting locations screw penetration depth is 4.6mm max. 7. Recommended screw torque: M3.5X0.6P = 6-8kgf-cm M4.0X0.7P = 8-10kgf-cm 8. Input: terminal block type. M4 screw torque value of 16kgf-cm using wire gauge 18-10 (13mm centers) 6 advancedenergy.com LCM1500 PIN ASSIGNMENT SIGNALS DESCRIPTION PIN # +Vout Power Rail SK3 GND Power Ground SK4 SIGNALS DESCRIPTION SK2 PIN NUMBER A2 EEPROM Address 1 -VPROG Return Connection of External Supply for Margin Programming 2 A1 EEPROM Address 3 -Vsense Remote Sense Return 4 ISHARE Load Share Voltage 5 A0 EEPROM Address 6 SDA1 Serial Data Signal (I2C) 7 +VPROG Positive Connection of External Supply for Margin Programming 8 SCL1 Serial Clock Signal (I2C) 9 +Vsense Remote Sense Positive 10 5VSB 5 V Standby 11 GND 5 V Standby Return 12 5VSB 5 V Standby 13 G_DCOK_C Global DCOK Collector 14 GPIOA6 EEPROM Write Protect 15 G_DCOK_E Global DC_OK Emitter (GND) 16 GND Return GND for O/P Signal and I2C communication 17 G_ACOK_C Global AC_OK Collector 18 INH_EN Turn Off Main Output 19 G_ACOK_E Global AC_OK Emitter (GND) 20 Note: Mating connector for SK2 is: LANDWIN (LWE PN: 2050S) Housing (LWE PN: 2053T) Contact CVILUX (CX PN: CI0120SD000) Housing (CX PN: CI01TD21PE0) Contact Signal Output Signal Connectors (SK2) PSU Front View (24V & 48V UNITS) CI0120P1HD0-LF advancedenergy.com 7 LCM1500 PIN ASSIGNMENT (CONTINUED) LED INDICATORS 2 provided are clearly visible up to a 45 degree offset from vertical with office environment ambient lighting. The status is reflected in the indicator color. The DC_OK LED shall light green if the DC output is within specification, and shall be off if the output falls out of specification. The AC_OK LED is green if the AC within specification and off when AC out of specification. CONTROL SIGNALS AC_OK open collector 0.5 V maximum at 10 mA. Both emitter and collector access provided. DC_OK open collector 0.5 V maximum at 10 mA. Both emitter and collector access provided. PS_INHIBIT/ENABLE Signal 0.0 to 0.5 V contact closure, output OFF OPTIONAL ACCESSORIES PIN 20 PIN 19 PIN 2 PIN 3 PIN 1 300 ± 5 mm Orderable kit part number: 73-788-001 PIN 20 PIN 19 PIN 2 PIN 3 PIN 1 Orderable kit part number: 73-788-002 8 advancedenergy.com LCM1500 MISCELLANEOUS SPECIFICATIONS BURN-IN 100% Burn-in at 45 °C, at 80% to 90% load. Duration of burn-in determined by Quality Assurance Procedures. MTBF The power supply has a minimum MTBF of 300K hours using the Bell core 332, issue 6 specification @ 25 °C and 40 °C, ambient, at full load. With the power supply installed in a system in a 25 °C ambient environment and operating at full load, capacitor life shall be 10 years, minimum for all electrolytic capacitors contained within this power supply. The power supply shall demonstrate a MTBF level of > 500,000 hours. QAV Full QAV testing shall be conducted in accordance with Advanced Energy standards. WARRANTY Artesyn Embedded Power shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of three years from the date of shipment, when operated within specifications. The warranty shall be fully transferable to the end owner of the equipment powered by the supply. advancedenergy.com 9 ABOUT ADVANCED ENERGY Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. For international contact information, visit advancedenergy.com. powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 Specifications are subject to change without notice. Not responsible for errors or omissions. ©2022 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks of Advanced Energy Industries, Inc. ENG-LCM1500-235-01.03.04.22