LPQ201-M

ARTESYN LPQ200-M SERIES 200 Watts Advanced Energy’s Artesyn LPQ200-M series of open-frame AC-DC power supplies comprises two quad output models, one offering 3.3 V, 5 V, 12 V and -12 V outputs, the other offering 5 V, 12 V, 24 V and -12 V. Both models feature medical safety approvals and accept a universal input of 90—264 Vac or 120—300 Vdc. These compact switch-mode power supplies feature main output overvoltage protection and remote sense, with short-circuit protection on all outputs. Additional facilities include thermal overload protection and remote indication of power failure. LPQ200-M series power supplies provide 100 watts of output power with free air convection cooling and 200 watts with 30 CFM of forced air. Less than 1U high, they are suitable for a wide range of uses, including non-patient contact and non-patient critical medical applications. SPECIAL FEATURES SAFETY  Medical and ITE safeties  TUV 62368, 60601-1  Active power factor correction  UL 62368, 60601-1  3” x 5” footprint  CSA 62368, 60601-1  Less than 1U high  CB Certificate & report  EN61000-3-2 compliant  CE Mark (LVD) DATA SHEET Total Power: 100 - 200 Watts Input Voltage: 90 - 264 Vac # of Outputs: Quad  Remote sense  Power fail  Adjustable outputs  Built-in Class B EMI filter  Overvoltage protection  Overload protection  Thermal overload protection  LPX200 enclosure kit available  RoHS compliant ©2020 Advanced Energy Industries, Inc. LPQ200-M ELECTRICAL SPECIFICATIONS Input Input ra­nge 90 - 264 Vac; 120 - 300 Vdc Frequency 47 - 63 Hz Inrush current 50 A max., cold start @ 25 °C, 230 Vac input Efficiency 84% typical at full load EMI/RFI FCC Class B conducted; CISPR22 Class B conducted; EN55022 Class B conducted; VDE0878PT3 Class B conducted Safety ground leakage current 275 μA @ 50/60 Hz, 264 Vac input Output Maximum power 100 W for convection; 200 W with 30CFM forced air Adjustment range All outputs -20%, +10%, except for the 3.3 V output which will be -15%, +10% (LPQ201-M) Hold-up time 16 ms @ 200 W load, 120 Vac input Overload protection Short circuit protection on all outputs. V1, V2 & V3 overload protected @ 110 - 160%. V4 is 150 - 250% above rating Overvoltage protection 30 - 50% above nominal output on V1 (and V2 on LPQ201-M) Logical Control Power failure Active low logic signal goes high 100-500 msec after main output; it goes low at least 6 msec before loss of regulation Remote sense Compensates for 0.4 V lead drop min. Will operate without remote sense connected. Reverse connection protected. ENVIRONMENTAL SPECIFICATIONS Operating temperature 0 °C to 50 °C ambient derate each output as 2.5% per degree from 50 °C to 70 °C. -20 °C start up Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 10% to 90% RH, non-operating, non-condensing 10 - 95% Vibration IEC68-2-6 to the levels of IEC721-3-2 MTBF calculated 516,000 hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore 2 advancedenergy.com LPQ200-M ORDERING INFORMATION Model Number LPQ201-M LPQ202-M Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30CFM Forced Air Peak Load Regulation +3.3 V 0A 13 A 18 A 20 A ± 2% 2 Ripple P/P 3 (PARD) 50 mV +5 V 0A 13 A 18 A 20 A ± 2% 50 mV +12 V 0A 5A 9A 10 A ± 5% 120 mV -12 V 0A 1A 2A 2.5 A ± 5% 120 mV +5 V 0A 13 A 18 A 20 A ± 2% 50 mV +12 V 0A 5A 9A 10 A ± 5% 120 mV +24 V 0A 1.5 A 3A 3.5 A ± 7% 240 mV -12 V 0A 1A 2A 2.3 A ± 5% 120 mV 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2­. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3­. Peak-to-peak with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. T his product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. PIN ASSIGNMENTS Connector LPQ200-M SK1 PIN 1 PIN 3 Line SK2 PIN 1 V1 OUT PIN 2 V2 OUT PIN 3 GND OUT PIN 4 GND OUT PIN 5 GND OUT PIN 6 GND OUT PIN 7 V3 OUT SK3 Neutral PIN 8 V4 OUT PIN 1 +V1 Remote sense PIN 2 -V1 Remote sense PIN 3 N/C PIN 4 N/C PIN 5 +Power fail PIN 6 Common PIN 7 N/C PIN 8 Common PIN 9 +V2 Remote Sense (LPQ201-M only) PIN 10 -V2 Remote Sense (LPQ201-M only) advancedenergy.com 3 LPQ200-M MATING CONNECTORS AC Input (SK1) Molex 09-50-3031 (connector) PINS: 08-52-0072 AC Ground Molex 01-90020001 DC Output (SK2) Terminal block Wire size based on Cable Ampacity/AWG Control Signals (SK3) Molex 90142-0010 (USA) PINS: 90119-2110 or AMP: 87977-3 PINS: 87309-8 Astec connector kit #70-841-015, includes all of above 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm) 3. Mounting holes MH1 and MH2 should be grounded for EMI purposes. 4. Mounting hole MH1 is safety ground connection. 5. Specifications are for convection rating at factory settings at 115 Vac input, 25 °C unless otherwise stated. 6. This power supply requires mounting on metal standoffs 0.20” (5 m) in height. 7. Warranty: 2 years 8. Weight: 1.5 lbs/0.68 kg 4 advancedenergy.com 0.06 (1.5) (2X) 0.472 (12) V4 Adjust POT Ø4 (4X) Mounting Hole PIN -8 SK2 V3 Pot Adj PIN -1 PIN -5 SK3 PIN - 10 2.55 (64.8) MH1 Saety Gnd 100W V1 Pot Adj V2 Pot Adj. 0.224 (5.7) (4X) 0.224 (5.7) (4X) PIN -1 SK 1 PIN -3 Ground Tab 4.55 (115.6) 5.00 (127) Output Voltage Adjust POTs LPQ200-M MECHANICAL DRAWING 3.00 (76.2) 0.098 (2.5) 1.32 (33.6) max advancedenergy.com 5 ABOUT ADVANCED ENERGY Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. For international contact information, visit advancedenergy.com. powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 Specifications are subject to change without notice. Not responsible for errors or omissions. ©2020 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks of Advanced Energy Industries, Inc. ENG-LPQ200-M-235-01 12.28