LPS152

Embedded Power for Business-Critical Continuity Rev. 08.17.07 LPS150 Series 1 of 3 LPS150 Series 150 Watts Total Power: 100 - 150 Watts Input Voltage: 85-132 /170-264 Vac 220 - 300 Vdc # of Outputs: Single Electrical Specifications Input Special Features Input ra­nge 85 - 132 Vac or 170 - 264 Vac automatically selected; 220 - 300 Vdc • • • • • • • • • • • • Frequency 47 - 63 Hz Inrush current 38 A max, cold start @ 25 °C Efficiency EMI filter 75% typical at full load FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Safety ground leakage current 0.5 mA @ 50/60 Hz, 264 VAC input Auto ranging input Remote sense Remote inhibit Power fail Single wire current sharing Built-in EMI filter Low output ripple Adjustable output 135 khz switching frequency Overvoltage protection Overload protection Optional cover (-C suffix) Output Maximum power Adjustment range Hold-up time Overload protection Safety VDE UL CSA NEMKO BABT CB CE 0805/EN60950 (IEC950) 11774-3336-1260 (LC#88585) UL1950 EI32002 CSA 22.2-234 Level 3 LR53982 EN 60950/EMKO-TUE P95102999 (74-sec) 203 EN60950/BS7002 607019 Certificate and report 2062 Mark (LVD) 110 W convection (75 W with cover) 150 W with 30 CFM forced air (130 W with cover) ± 5% minimum on the main outputs 20 ms @ 110 W load, 115/230 Vac nominal lline Short circuit protection. Case overload protected @ 110% to 145% above peak rating Overvoltage protection 5  V output: 5.7 to 6.7 VDC. Other outputs 10% to 25% above nominal output Logic Control Power failure TTL Logic signal goes high 50 - 150 msec after 5 V output. It goes low at least 3 ms before loss of regulation Remote inhibit Requires an external TTL high signal to inhibit outputs Remote sense Compensates for 0.5 V lead drop minimum, will operate without remote sense connected. Reverse connection protected Embedded Power for Business-Critical Continuity Rev. 08.17.07 LPS150 Series 2 of 3 Environmental Specifications Operating temperature: Storage temperature: 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70 °C -40 °C to +85 °C Temperature coefficient: ± 0.4% per °C Electromagnetic Designed to meet IEC 801, -2, -3, -4, -5, -6, Level 3 susceptibility: Humidity: Operating; non-condensing 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5Hz to 500Hz, operational MTBF demonstrated: > 550,000 hours at full load and 25 °C ambient conditions Ordering Information Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30CFM forced Air LPS152 5V 0A 22 A 30 A 35 A ± 2% LPS153 12 - (15) V 0A 9.1 A 12.5 A 14.5 A ± 2% 150 mV LPS155 24 - (28) V 0A 4.5 A 6.2 A 7.2 A ± 2% 280 mV, max. Peak Load 1 Regulation 2 Ripple P/P (PARD)3 50 mV 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. Mating­ Connectors Pin Assignments Connector SK1 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 SK2 PIN 5 PIN 6 PIN 7 SK3 TB-1 TB-2 SK4 PIN 1 PIN 3 PIN 5 LPS152 INHIBIT -ve INHIBIT +ve VCC No Connection COMMON -SENSE +SENSE C SHARE COMMON PIN REMOVED POK COMMON +5 V GROUND LINE NEUTRAL LPS153 INHIBIT -ve INHIBIT +ve VCC No Connection COMMON -SENSE +SENSE C SHARE COMMON PIN REMOVED POK ­COMMON +5 V GROUND LINE NEUTRAL LPS155 INHIBIT -ve INHIBIT +ve VCC No Connection COMMON -SENSE +SENSE C SHARE COMMON PIN REMOVED POK COMMON +5 V GROUND LINE NEUTRAL AC input (SK4): Power fail (SK2): Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 Molex 09-50-8031 (USA) Molex 09-91-0300 (UK) PINS: 08-58-0111 Molex 51110-0851 (USA) PINS: 50394-8100 Remote sense/ Remote inhibit (SK1): Astec Connector Kit #70-841-009, includes all of the above 1. Specifications subject to change without notice. ­2. All dimensions in inches (mm), tolerance is ±0.02”­­ (±0.5mm) 3. Specifications are for convection rating at factory settings unless otherwise stated 4. Remote inhibit requires an external 5V @ 10mA to activate. 5. Mounting (6-32) maximum insertion depth is 0.12”. 6. Warranty: 2 year 7. Weight: 1.75 lbs/0.80 kg Embedded Power for Business-Critical Continuity Rev. 08.17.07 LPS150 Series 3 of 3 Mechanical Drawing SK1 8765 SK3 2 1 SK2 1234 ­Americas #6-32 (8 places) .5625 7 6 5 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) Do Not Adjust Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Output Adjust 7.4 (188.0) 8.5 (216.0) Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.Emerson.com/EmbeddedPower techsupport.embeddedpower @emerson.com 531 4.25 (108.0) SK4 .75 (19.0) 1.5 (38.1) While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power .875 (22.25) 2.5 (63.5) Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2010 Emerson Electric Co.