ARTESYN
LPT100-M Series
130 Watts
Advanced Energy's Artesyn LPT100-M series of triple output
open-frame AC-DC power supplies features ITE and medical
safety approvals. There is a choice of four models, covering
output voltages from 3.3 V to 24 V. The power supplies have
a typical full load power conversion efficiency of 82% and
with a height of only 1.28 inches offer a power density in
excess of 12 watts per cubic inch. LPT100-M power supplies
are primarily designed for use in information technology
equipment (ITE) and light industrial systems, as well as for
equipment intended for non-patient contact and non-patient
critical use in low power medical, dental and laboratory
applications.
Special Features
Thermal overload protection
Medical and ITE safeties
RoHS compliant
Active power factor correction
2” x 4” footprint
Less than 1U high
EN61000-3-2 compliant
Remote sense
Power fail
Adjustable main output
Built-in Class B EMI filter
Overvoltage protection
Overload protection
Data Sheet
Total Power:
130 Watts
Input Voltage:
90 - 264 Vac
# of Outputs:
Triple
LPX100 enclosure kit available
Safety
TUV
62368, 60601-1
UL
62368, 60601-1
CSA
62368, 60601-1
NEMKO
62368, 60601-1
AUSTEL
62368, 60601-1
CB
Certificate & report
CE
Mark (LVD)
©2020 Advanced Energy Industries, Inc.
LPT100-M
ELECTRICAL SPECIFICATIONS
Input
Input range
90 - 264 Vac; 127 - 300 Vdc
Frequency
47 - 63 Hz
Inrush current
50 A max., cold start @ 25 °C
Efficiency
82% typical at full load
EMI/RFI
FCC Class B conducted; CISPR22 Class B conducted;
EN55022 Class B conducted; VDE0878PT3 Class B conducted
Safety ground leakage current
275 µA @ 50/60 Hz, 264 Vac input
Output
Maximum power
130 W with 200 LFM forced air
Adjustment range
All outputs adjustable: -20%, +10%, except for +24V output on LPT104-M which will be -10%, +20%
and 3.3 V output on the LPT101-M +10%, -15%
Hold-up time
10 ms @ 130 W load, 120 Vac input
Overload protection
Short circuit protection on all outputs. Case overload protected @ 110 - 160% above rating for
V1 & V2, 150 - 250% for V3
Overvoltage protection
15 - 35% above nominal output
Logical Control
Power failure
Active LowTTL logic signal goes high 100 - 500 msec after main output; it goes low at least 6 msec
before loss of regulation
Remote sense
Compensates for 0.5 V lead drop min. Will operate without remote sense connected.
Reverse connection protected.
Environmental Specifications
Operating temperature
0 °C to 50 °C ambient derate each output as 2.5% per degree from 50 °C to 70 °C. -20 °C start up
Storage temperature
-40 °C to +85 °C
Electromagnetic susceptibility:
Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity
Operating; non-condensing 10% to 90% RH, non-operating, non-condensing 10% - 95%
Vibration
IEC68-2-6 to the levels of IEC721-3-2
MTBF calculated
583,000 hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore
2 advancedenergy.com
LPT100-M
Mechanical Drawing
ADJUST POT'S
1
GND
SK2
PIN 1 (LIVE)
8
PIN 3 (NEUTRAL)
0.16
[4]
4 places mounting hole
max screw head
diameter 0.22"[5.6]
1.72 "
[43,8]
SK1
SK3
SEE DETAIL A
1
3.72 "
[94,6]
4"
[101,6]
4
POWER FAIL
COMMON
(+) REMOTE SENSE
(-) REMOTE SENSE
0.1 "
[2,5]
max lead
protrusion
1.29 "
[32,7]
SK3
DETAIL A
0.197
[5]
min stand-off
height
2"
[50,8]
OUTPUT VOLTAGE
advancedenergy.com
3
LPT100-M
Ordering Information
Model Number
LPT101-M
LPT102-M
LPT103-M
LPT104-M
Ripple
3
P/P (PARD)
Output Voltage
Minimum Load
Maximum Load with
30CFM Forced Air
+3.3 V
0A
+5 V
0A
+12 V
+5 V
+12 V
0A
-12 V
0A
2A
+5 V
0A
18 A
+15 V
0A
7.2 A
8A
-15 V
0A
1.5 A
+5 V
0A
18 A
+24 V
0A
3A
3.5 A
±7%
240 mV
+12 V
0A
2.3 A
2.3 A
±5%
120 mV
Peak Load
Regulation
18 A
20 A
±2%
50 mV
9A
10 A
±5%
50 mV
0A
2.3 A
2.3 A
±5%
120 mV
0A
18 A
20 A
±2%
50 mV
9A
10 A
±5%
120 mV
2A
±5%
120 mV
20 A
±2%
50 mV
±5%
150 mV
2A
±5%
150 mV
20 A
±2%
50 mV
2
1. Peak current lasting < 15 seconds with a maximum 10% duty cycle.
2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4. T his product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC
compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not
intended for sale to End Users.
4 advancedenergy.com
LPT100-M
Pin Assignments
Connector
LPT100-M
SK1
PIN 1
Live
PIN 3
Neutral
PIN 1
V1out
PIN 2
V1out
PIN 3
GND
PIN 4
GND
PIN 5
GND
PIN 6
GND
PIN 7
V2out
SK2
SK3
PIN 8
V3out
PIN 1
Power Fail
PIN 2
GND
PIN 3
+ Remote Sense
PIN 4
- Remote Sense
Mating Connectors
AC Input (SK1)
Molex 09-50-3031
PINS: 08-52-0072
AC Ground
Molex 01-90020001
DC Output (SK2)
JST VHR-8N
PINS: SVH-21T-P1.1
Remote Sense (SK3)
JST PHR-4; PINS: SPH-002T-PO.5S
OR
LANDWIN 2001S0400; PINS: 2005T
Artesyn Embedded Power Connector Kit #70-841-026, includes all of the above
Notes:
1. Specifications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ±.02”.
3. All mounting holes should be grounded for EMI purpose
4. Mounting M1 is safety ground connection
5. This power supply requires mounting on metal standoffs 0.20” (5 m) in height.
6. For DC input an external DC safety rated fuse must be used.
7. Warranty: 2 year
8. Weight: 0.44 lb. / 0.20 kg
advancedenergy.com
5
ABOUT ADVANCED ENERGY
Advanced Energy (AE) has devoted more than three
decades to perfecting power for its global customers. AE
designs and manufactures highly engineered, precision
power conversion, measurement and control solutions for
mission-critical applications and processes.
Our products enable customer innovation in complex
applications for a wide range of industries including
semiconductor equipment, industrial, manufacturing,
telecommunications, data center computing, and medical.
With deep applications know-how and responsive service
and support across the globe, we build collaborative
partnerships to meet rapid technological developments,
propel growth for our customers, and innovate the future
of power.
For international contact information,
visit advancedenergy.com.
powersales@aei.com (Sales Support)
productsupport.ep@aei.com (Technical Support)
+1 888 412 7832
Specifications are subject to change without notice. Not responsible
for errors or omissions. ©2020 Advanced Energy Industries, Inc. All rights
reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks
of Advanced Energy Industries, Inc.
ENG-LPT100-M-235-01 12.30
