M3000-86-5

M3000 and M4000 SERIES Single output • • • • • • • • Load currents up to 800A 3 phase or single phase input Shutdown on phase loss 3 phase power factor correction Single wire current share to 5% Ideal for N+1 applications Current monitor output included UL, CSA and TÜV safety approvals [ 2 YEAR WARRANTY ] The M series is a range of single output, high current power supplies ideally suited to a broad range of applications. Robust performance and field proven reliability are hallmarks of this series. Field reliability in excess of 100,000 hours has been documented. The M series will provide stable power for any large electronic system including telecommunication, data processing and industrial. Typical applications include broadcast systems, ATM systems and RISC processors and systems. Semiconductor test equipment, semiconductor and wafer processing equipment and functional board level testers are other possible applications. Industrial uses include applications such as laser cutting, water purification, battery charging, machine control, large scale data logging and optical inspection equipment. Current sharing, built-in current monitoring, voltage margining and remote adjustment capability are standard features. Other system interface features include AC and DC good, OVP, OCP, over temperature protection and remote enable. Worldwide safety certifications are included. SPECIFICATION OUTPUT SPECIFICATIONS Voltage adjustability Remote sense All specifications are typical at nominal input, full load at 25°C unless otherwise stated EMC CHARACTERISTICS ±10% Radiated emissions Conducted emissions Electrostatic discharge RF field susceptibility Electrical fast transients/bursts Surge susceptibility EN55022/11, FCC part 15 EN55022/11, FCC part 15 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 Level A Level A Level 3 Level 3 Level 3 Level 3 Accessible at front panel Open/reverse sense lead protection Compensates for voltage drop of up to 0.5V to the load ±0.2%; 10mV Regulation, line or load All outputs, NL to FL at nominal line or all line variations at FL Overshoot/undershoot Transient response Main output 25% step load change at 1A/µs GENERAL SPECIFICATIONS ≤5.0% max. dev., ≤200µs recovery to 1.0% 0.02%/°C Hold-up time Efficiency Isolation voltage 230VAC, 3KW load 208VAC, 3 phase Input/output Input/chassis Output/output 25ms min. 83% 3000VAC 1500VAC 500VAC 100kHz TÜV EN60950, UL1950, CSA C22.2 No. 950 13kg (29Ibs) 5 x 8 x 13.5 inches 127 x 203.2 x 342.9 mm >100,000 hours None at turn on/off Temperature coefficient Ripple and noise Overvoltage protection Overload protection Short circuit protection Thermal protection Current sharing Current monitor (V1) ±5.0% 5VDC at full load 0Hz to 20MHz 100mV pk-pk or 1.0% 115% to 130% of nominal Switching frequency Approvals and standards Weight Size MTBF Reset by cycling AC 105% to 115% full load 90% of rated load Auto recovery Auto shutdown, AC reset 50% to 100% load ±0.5V ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating ambient Non-operating 50CFM Non-condensing Operating Non-operating 5Hz to 500Hz 0°C to +50°C -15°C to +85°C Internal DC ball bearing fans 0% to 95% RH 6,000 feet max. 55,000 feet max. 2.4G rms peak INPUT SPECIFICATIONS Input voltage range Input frequency range Input surge current Input current Power factor Power up time 3 phase 1 phase (optional) 180 to 264VAC 180 to 264VAC 47Hz to 63Hz Meets IEEE std. 587.1980; 3KV ring wave 208VAC, 3 phase 208VAC, 1 phase 3 phase 1 phase Full load 12A 27A 0.94 0.65 1.0s max. Cooling Relative humidity Altitude Vibration PAGE 1 MEDIUM TO HIGH POWER AC/DC POWER SUPPLIES | 3000-4000W AC/DC 3000 and 4000 Watt AC/DC high current power supplies with PFC MAX. OUTPUT POWER 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 3000W 4000W 4000W STANDARD CONTROL SIGNALS Remote Enable DC OK (See Figures 2, 5) AC Good (See Figures 2, 5) Margin Hi/Lo (V1) (See Figure 3) Remote Adjust (See Figure 4) Current Monitor See Figure 1A Signal remains "Hi" as long as output is ±5.0% of nominal Signal "Hi" when AC >175VAC and "Lo" when 10ms Analog signal indicates load current in single or parallel operation. 5±0.5VDC represents FL, resistive load 103kΩ Overvoltage, overtemperature indicated by 'low' signal > 5msec DC Outputs Supply Fault DC Good Flag FIG. 1A 5V 3 3 FIG. 1B 5V FIG. 2 (Ref. FIG. 5) 5V 5V FIG. 3 5V Close to Margin High 5K 5K 10K FIG. 4 5V = -10% 7 >10K 2.5V Nominal 6 10 10 Close to Enable Close to Inhibit (optional) (optional) 13 Close to Margin Low Return = +10% http://www.artesyn.com PAGE 2 3000-4000W AC/DC | MEDIUM TO HIGH POWER AC/DC POWER SUPPLIES 3000 and 4000 Watt AC/DC high current power supplies with PFC Mechanical notes A AC connector is 4 position terminal block (#8 screws included), mating to #8 ring tongue terminal. B DC output is 5/16-18 studs mating to 5/16 terminal lugs. C J-1 signal connector is Molex 39-30-1140 or equivalent. Mating connector is Molex 39-01-2140 or equivalent. D J-2 signal connector is Molex 39-01-1120 or equivalent. Mating connector is 39-01-2120 or equivalent. E Signal connector contacts are Molex 39-00-0039 or equivalent. F Auxiliary DC output(s) are 6 position terminal block (#8 screws included) mating to #8 ring tongue terminal. G TB1 and J2 are not installed on single output models. PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OUTPUT PIN CONNECTIONS J1 REFERENCE + Remote Sense Note 1 - Remote Sense Note 1 Enable Notes 2 & 4, Fig. 1 DC OK Inverse (Optional) Notes 3 & 4, Fig. 2 AC Good Inverse Notes 3 & 4, Fig. 2 Margin High Fig. 3 Remote Adjust Fig. 4 Current Monitor Note 6 Current Share Note 6 Inhibit (Optional) Notes 2 & 4, Fig. 1 DC OK Notes 3 & 4, Fig. 2 & 5 AC Good Notes 3 & 4, Fig. 2 & 5 Margin Low Note 3 Supply Fault Notes 5 & 6 - Remote Sense Output pin connector notes 1 2 3 4 5 6 Use 20AWG or larger twisted pair. Switch on voltage must be