MP6-2R-4EE-4LL-0N

ARTESYN INTELLIGENT MP SERIES Up to 1500 Watts Advanced Energy's Artesyn iMP series is an AC input to DC output configurable power system consisting of a microprocessor-controlled PFC front end providing seven slots that accept intelligent DC-DC converter modules with single, dual or triple outputs ranging from 2 V to 60 V. Single output modules come in four power ranges that can be mixed and matched and connected in parallel or series to obtain thousands of output combinations customized to any application. SPECIAL FEATURES  Optional extended hold-up module  Full medical EN60601 approval  Increased power density to 50% over 2  Intelligent I C control  Voltage adjustment on all outputs (manual or I2C)  Configurable input and output OK signals and indicators  Configurable inhibit/enable  Configurable output UP/DOWN sequencing  Configurable current limit (foldback or constant current)  High power density (8.8 W/cu-in)  Intelligent fan (speed control/fault status)  Downloadable GUI from website  Customer provided air option  uP controlled PFC input with active inrush protection 2  I C monitor of voltage, current, and (SEMI F47 compliance) AT A GLANCE Total Power: Up to 1500 W Input Voltage: 85 to 264 Vac 120 to 300 Vdc # of Outputs: Up to 21 standard MP  External switching frequency sync input  Optional conformal coating  Industrial temp range (-40 ºC to 70 ºC)  No preload required  Industrial shock/vibration (> 50G’s) SAFETY  UL UL60950/ES60601-1  CSA CSA C22.2 No. 60950-1-07/ CSA C22.2 No. 60601-1  TUV EN62368-1/EN60601-1  CB Certificate and report  CE Mark to LVD  CCC temp  Programmable voltage, current limit, inhibit/enable through I2C ©2021 Advanced Energy Industries, Inc. IMP ELECTRICAL SPECIFICATIONS Input Input ra­nge 85 to 264 Vac; 120 to 300 Vdc (limited to 300 Vdc in medical applications) Frequency 47 to 63 Hz (iMP1 47 to 440 Hz) Inrush current 40 A peak maximum (soft start) Efficiency Up to 85% @ full case load Power Factor 0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz) Turn-on time AC on 2.0 sec typ., inhibit/enable 150 ms typical Programmable delay; 50 ms internal turn-on delay (Dual Output only) EMI filter CISPR 22/EN55022 Level “B”** Leakage current 300 µA max. @ 240 Vac; 47 - 63 Hz Radiated EMI CISPR 22/EN55022 Level “B”** Holdover storage 20 ms minimum (independent of input Vac) additional 34 ms holdover storage with optional HUP module (SEMI F47 compatible). For iMP4 15 ms (low-line), 10 ms (high-line) AC OK > 5 ms early warning min. before outputs lose regulation Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W @ 90 Vac) Harmonic distortion Meets EN61000-3-2 Isolation Meets EN60950 and EN60601 Input to output: 4000 Vac; input to ground: 1500 Vac; output to ground: 400 Vdc Meets 1 MOPP Primary to ground, 2 MOPP Primary to Secondary Global inhibit / enable TTL, Logic “1” and Logic “0”; configurable Input fuse (internal) iMP4: 16 A; iMP8: 20 A; iMP1: 25 A (both lines fused) Warranty 2 years 2 advancedenergy.com IMP ELECTRICAL SPECIFICATIONS (CONTINUED) Output Adjustment range* ± 10% minimum all outputs (manual) (full module adjustment range using I2C) Factory set point accuracy 1% 2 I C output program accuracy ± 5% Margining ± 4 - 6% nominal analog (single output module only) Overall regulation 0.4% or 20 mV max. (1500 W modules 1% max.) (36 W modules 4% maximum) Ripple RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to 20 MHz Dynamic response < 2% or 100 mV, with 25% load step Recovery time To within 1% in < 300 µsec Overcurrent protection** Configurable through I2C (calibration required). Single output module and main output of the dual output module 105 - 120% of rated output current. Aux output of dual output module 105 - 140% of rated output current Short-circuit protection Protected for continuous short-circuit. Recovery is automatic upon removal of short Overvoltage protection* Configurable through I2C Single output module: 2 to 5.5 V 122 to 134%; 6 to 60 V 110 to 120% Dual output module: 2 to 6 V 122 to 134%; 8 to 28 V 110 to 120% Triple output module: 110 - 120% of highest voltage rating Thermal protection* (OTP and OTW) Configurable through I2C All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before shutdown Remote sense Up to 0.5 V total drop (not available on triple output module) Single wire parallel Current share to within 2% of total rated current DC OK* ± 5% of nominal. Configurable through I2C Minimum load Not required Housekeeping bias voltage 5 Vdc @ 1.0 A max. present whenever AC input is applied (Optional 2.0 A available) Module inhibit* Configured and controlled through I2C Switching frequency 250k Hz accepts external sync signal Output/Output isolation > 1 Megohm, 500 V External sync TTL clock input signal used to adjust switching frequency. Frequency 500 kHz ± 20%; Duty cycle 40 - 55% * Can be controlled via I 2C ** Controlled via I 2C but requires load calibration INTERNAL PART NUMBER REFERENCE TABLE Part # Description Case Code 73-580-0001i iMP8 Case iMP8 73-690-0001i iMP1 Case iMP1 73-540-0001i iMP4 Case iMP4 advancedenergy.com 3 IMP ENVIRONMENTAL SPECIFICATIONS Operating temperature -40 °C to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C. (-20 °C start up) Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 10% to 95% RH Vibration IEC68-2-6 to the levels of IEC721-3-2 MTBF demonstrated > 550,000 hours at full load, 220 Vac and 25 °C ambient conditions OUTPUT MODULE LINE-UP 1 2 3 5 4 — Module Type Single Single Single Single Dual Triple Max output power 210 W 360 W 750 W 1500 W 144 W 36 W Max output current 35 A 60 A 150 A 300 A 10 A 2A 2 to 60 V 2 to 60 V 2 to 60 V 2 to 60 V 2 to 28 V 2 to 28 V 25 25 25 18 Module Code Output voltages available Standard voltage increments 16 18 V1 V2 V1,V2,V3 Remote sense Yes Yes Yes Yes Yes Yes No Remote margin Yes Yes Yes Yes No No No V-Program - I2C Control Yes Yes Yes Yes Yes Yes No Active Current Share Yes Yes Yes Yes Yes No No Module Inhibit - I2C Control Yes Yes Yes Yes Yes Yes Yes Module Inhibit - Analog Yes Yes Yes Yes Yes No No Overvoltage/Overcurrent protection Yes Yes Yes Yes Yes Yes Yes Minimum load required No No No No No No No 1 2 3 4 Slots occupied in any iMP case 4 advancedenergy.com 1 1 IMP OUTPUT MODULE VOLTAGE/CURRENT* Voltage Voltage Code 1 2 3 5 4 4 - - - I2C Adjustment Ranges*** Single Output Module Code Dual Output** Triple Output 2V A 35 A 60 A 150 A 300 A 10 A 10 A — — 2A 1.8 - 2.2 2.2 V B 35 A 60 A 150 A 300 A 10 A 10 A — — 2A 2.0 - 2.4 3V C 35 A 60 A 150 A 300 A 10 A 10 A — — 2A 2.7 - 3.3 3.3 V D 35 A 60 A 150 A 300 A 10 A 10 A — — 2A 3.0 - 3.6 5V E 35 A 60 A 150 A 300 A 10 A 10 A — — 2A 4.5 - 5.5 5.2 V F 35 A 60 A 144 A 288 A 10 A 10 A — — 2A 4.7 - 5.7 5.5 V G 34 A 58 A 136 A 273 A 10 A 10 A — — 2A 5.0 - 6.1 6.0 V H 23 A 42 A 97.5 A 250 A 10 A* 10 A* — — 2A 5.4 - 6.6 8.0 V I 20 A 36 A 84.4 A 187.5 A 10 A 4A 1A 1A 1A 7.2 - 8.8 10 V J 18 A 32 A 75 A 140 A 10 A 4A 1A 1A 1A 9.0 - 11.0 11 V K 17 A 31 A 68 A 136.3 A 10 A 4A 1A 1A 1A 9.9 - 12.1 12 V L 17 A 30 A 62.5 A 125 A 10 A 4A 1A 1A 1A 10.8 - 13.2 14 V M 14 A 21 A 53.5 A 107 A 9A 4A 1A 1A 1A 12.6 - 15.4 15 V N 14 A 20 A 50 A 100 A 8A 4A 1A 1A 1A 13.5 - 16.5 18 V O 11 A 19 A 41.6 A 83.3 A — — — 0.5 A 0.5 A 16.2 - 19.8 20 V P 10.5 A 18 A 37.5 A 75 A — — — 0.5 A 0.5 A 18.0 - 22.0 24 V Q 8.5 A 15 A 30 A 62.5 A 4A 2A — 0.5 A 0.5 A 21.6 - 26.4 28 V R 6.7 A 11 A 26.8 A 53.5 A 3A 2A — 0.5 A 0.5 A 25.2 - 30.8 30 V S 6.5 A 11 A 25 A 50 A — — — — — 27.0 - 33.0 33 V T 6.2 A 10.9 A 22.7 A 35.8 A — — — — — 29.7 - 36.3 36 V U 5.8 A 10 A 20.8 A 35.8 A — — — — — 32.4 - 39.6 42 V V 4.2 A 7.5 A 16 A 35.7 A — — — — — 37.8 - 46.2 48 V W 4.0 A 7.5 A 15.6 A 31.2 A — — — — — 43.2 - 52.8 54 V X 3.7 A 6.0 A 13.9 A 27.7 A — — — — — 48.6 - 59.4 60 V Y 3.5 A 6.0 A 12.5 A 25 A — — — — — 54.0 - 66.0 35 A 60 A 150 A 300 A — 10 A Contact Factory Special* Z 2.3 - 2.6 Special* Z 35 A 60 A 150 A 300 A — 10 A 3.7 - 4.4 Special* Z 20 A 36 A 80 A 140 A — 8A 6.7 - 7.1 * Increments of current not shown can be achieved by paralleling modules (add currents of each module selected). **Total output power on dual model must not exceed 144 W. *** For single output modules only. Bold black lines reference lines indicate physical module groupings advancedenergy.com 5 IMP OUTPUT MODULE VOLTAGE/CURRENT* (CONTINUED) Slot 1 Slot 1 Slot 2 Slot 2 Ordering Notes Slot 2 Slot 4 Slot 3 Slot 3 Slot 3 Slot 4 Slot 4 Slot 6 Slot 7 Slot 6 Slot 5 Slot 5 Slot 5 Parallel Codes 7 6 5 4 3 2 1 iMP4 available slots 1. The cases and modules of both MP and iMP series can be interchanged to allow more flexibility. If intelligent modules are used with non-intelligent cases, a numeric code “4” is placed at the end of the module code (ex. 4LL0 becomes 4LL4). iMP8 available slots iMP1 available slots 2 2. USB to I C module order code 73-769-001 0 = no parallel 1=1&2 2=2&3 3=3&4 4=4&5 5=3&4&5 6=5&6 7=4&5&6 8=6&7 9 = 3 & 4, 6 & 7 A = 1 & 2, 3 & 4, 5 & 6 C = 2 & 3, 4 & 5 E = 3 & 4, 5 & 6 F = 2 & 3, 4 & 5, 6 & 7 ORDERING INFORMATION Case Size iMP1* Case Size (mm) 4 = 2.5” x 5” x 10”; 750 W - 1158 W, 5 Slots (63.5 x 127 x 254 mm) 8 = 2.5” x 7” x 10”; 1000 W - 1200 W, 6 Slots (63.5 x 177.8 x 254 mm) 1 = 2.5” x 8” x 11”; 1200 W - 1500 W, 7 Slots (63.5 x 203.2 x 279.4 mm) * Note: Add “E” after iMP4 to denote IEC input option. e.g. iMP4E (Not available on iMP8 or iMP1) 6 advancedenergy.com Module/Voltage/Option Codes First - Module Code Second - Voltage Code Third - Option Code - 3L0 - 2E2 - 1Q1 - 4LL0 Module Codes Module/voltage/option codes Module codes: (None) = 36 W triple O/P (1 slot) 1 = 210 W single O/P (1 slot) 2 = 360 W single O/P (2 slot) 3 = 750 W single O/P (3 slot) 4 = 144 W dual O/P (1 slot) 5 = 1500 W single O/P (4 slot) 6 - 9 = future Voltage Codes: See Output Module Voltage/ Current table above Option Codes: 0 = Standard 1 = Module enable 2 = Constant current 3 = 1 & 2 combined 4 = Set for use in standard (non-intelligent case) 5 = Shutdown mode for 1500 W 6 = 1 & 5 combined 7 - 9 = future Case Option Codes - 00 Case Option Codes First digit 0 - 9, A - Z parallel code (See Parallel Codes table above) Second digit 0 = No options 1 = Reverse air 3 = Global enable 4 = Fan idle with inhibit 5 = Opt 1 + Opt 3 6 = Opt 1 + Opt 4 7 = Opt 3 + Opt 4 8 = Opt 1 +3 +4 9 = RS485 73-544-002 A = RS485 73-544-002 + Reverse air C = Opt 3 + Opt 9 D = CAN BUS 73-544-003 E = Opt 3 + Opt D F = RS485 - MODBUS 73-544-005 Software Code - A Software code used for configuration change. “A” is standard Hardware Code - ### Factory assembled for hardware of firmware mods. IMP ORDERING INFORMATION (CONTINUED) Single iMP4 (AC input on opposite side) 210 W S L O T S L O T S L O T S L O T S L O T 5 4 3 2 1 360 W -A- iMP4 = 2  .5” x 5” x 10” 5 available slots (63.5 x 127 x 254 mm) 90 - 264 Vac 750 W max. Input 180 - 264 Vac 1158 W max. iMP8 and iMP1 750 W S L O T 7 S L O T 6 S L O T 5 S L O T 4 S L O T 3 S L O T 2 S L O T 1 iMP1 only 1500 W ( 2.0 to 8.0 iMP8 = 2  .5” x 7” x 10” 6 available slots (63.5 x 177.8 x 254 mm) iMP1 = 2  .5” x 8” x 11” 7 available slots (63.5 x 203.2 x 279.4 mm) 85 - 264 Vac 1000 W max. Input 180 - 264 Vac 1200 W max. 1200 W max. 1500 W max. 1500 W ( 10 to 60 V) 1500 W with Bus Bar Adapter Option (used with the 10 to 60 V module) Dual 144 W Triple 36 W advancedenergy.com 7 IMP PIN CONNECTORS Figure 1. AC Input 1 2 AC Input N ~ 3 Pin No. Function 1 AC neutral 2 AC line (hot) 3 Chassis (earth) ground PFC Input Connector (Control and signals） Figure 2. Connector J1 5 10 Mates with Molex 90142-0010 Housing 90119-2110 Pin Connector Kit Part No.: 70-841-004 Figure 3. Connector J2 Pin No. Function 1 Input AC OK - “emitter” 2 Input AC OK - “collector” 3 Global DC OK - “emitter” 4 Global DC OK - “collector” 5 External Sync 6 Global inhibit/optional enable logic “0” 7 Global inhibit/optional enable logic “1” 8 Global inhibit/optional enable return 9 +5 VSB housekeeping 10 +5 VSB housekeeping return I2C Bus Output Connector 10 6 5 1 Mates with Landwin 2050S1000 Housing 2053T011V Pin or JST PHDR-10VS Housing JST SPHD-002T-P0.5 (28-24) JST SPHD-001T-P0.5 (26-22) Connector Kit Part No.: 70-841-023 8 advancedenergy.com Pin No. Function 1 No connection 2 No connection 3 No connection 4 Serial clock signal (SCL) 5 Serial data signal (SDA) 6 Address bit 0 (A0) 7 Address bit 1 (A1) 8 Address bit 2 (A2) 9 Secondary return (GND) 10 5 Vcc external bus (5 VCC. Bus) IMP MECHANICAL DRAWINGS iMP Modules Single 210 Watt .44” (11.2) 2X V+ DC-DC Converter Output Modules Control Signal Information, J1 Control Connector .48" + Remote Sense single or dual o/p main Remote Margin / V. Program single o/p 3 1 Margin N High single o/p 4 2 - Remote Sense / Margin Low 6 single or dual o/p main DC OUTPUT CONNECTOR Module, Isolated Inhibit single or dual o/p 7 Module Inhibit Return single or dual o/p 8 Current Share (SWP) single or dual o/p main 9 Figure 1.+ AC Input Sense V2 Remote dual o/p, single is spare - Remote Sense V2 dual o/p, single is spare 10 .32" (8.1) Single 360 Watt * Note: All iMP modules have a green DCOK LED. (except for 36 W module) Figure 4. Connector J1 5 10 1 6 Mates with Molex 90142-0010 Housing 90119-2110 Pin Figure 2. Connector J1 Single 750 Watt Single 1500 Watt 2-8 V .63" (16.0) .63” .33” (16.0) (8.5) V+ M 4 X 8 SCREWS WITH CONICAL WASHER .48” (12.1) (2X) 3 ~ Spare V- 1.38” (35.2) (2X) 5 V ADJ PIN 1 PIN 1 V ADJ .44” (11.4) 2 V- .44" (11.4) 1 M4X8 SCREWS WITH CONICAL WASHER (12.1) Function 1.38" (35.1) Pin No. DC OUTPUT CONNECTOR .32” (8.1) Single 1500 Watt 10-60 V 59.3 ± 0.2 V+ (3x) 31.6 ±0.8 .59" (15.0) 11.3 ±0.8 (2x) 15.0 ±0.8 (2x) 16.0 ±0.2 DC OUTPUT CONNECTOR PIN 1 (2x) 16.0 ±0.2 For Factory-Use Only .44" (11.0) 1.24"(31.5) (2X) .61"(15.6) (2X) 8.1 ±0.8 M4X8 SCREWS W/ CONICAL WASHER (6X) VADJ V- .32" (8.1) PIN 1 V ADJ M4X8 SCREWS (4X) DC OUTPUT CONNECTOR V- V+ Dual 144 Watt .46 (11.7) (4X) V1 + V1 V2 + (3X) .30 (7.5) 1.17 (29.7) .42 (10.7) .32 (8.1) V2 M3X8 SCREWS WITH SPRING WASHER (4X) Triple 36 Watt V1 ADJ V2 ADJ V1 + V1+ V2+ V3+ V3 ADJ V1V2V3- V1 V2 + V2 V3 + V3 - V2 ADJ V1 ADJ PIN 1 Mates with Molex 09-91-0600 Housing 26-60-5060 Pin advancedenergy.com 9 IMP IMP SERIES iMP4 (750/1158 Watts Max) 5-Inch Case Size: iMP4: 2.5” x 5” x 10” (63.5 mm x 127 mm x 254 mm) Weight: iMP4 Case: 3 lbs. • 360 W Single 1.0 lb. • 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb. Notes: 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). (Optional IEC input connector) 2. C ontrol connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. O  utput module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m). 10 advancedenergy.com IMP 171.45 xy 171.45 Reverse Air Flow Normal Air Flow iMP8 (1000/1200 Watts Max) 7-Inch Case Size: iMP8: 2.5” x 7” x 10” (63.5 mm x 177.8 mm x 254 mm) Weight: iMP8 Case: 4.1 lbs. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb. 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb. xy #8-32 MOUNTING HOLES (4X) MARKED AS Y 38.10 M4 MOUNTING HOLES (4X) IDENTICAL BOTH SIDES IMP SERIES (CONTINUED) Notes: 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. C ontrol connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series) Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. O  utput module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m). advancedenergy.com 11 IMP IMP SERIES (CONTINUED) iMP1 (1200/1500 Watts Max) 8-Inch Case Size: iMP1: 2.5” x 8” x 11” (63.5 mm x 203.2 mm x 279.4 mm) Weight: iMP1 Case: 5.0 lb. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb. 750 W Single: 1.6 lb. • 144 W Dual: 0.6 lb. Normal Air Flow Reverse Air Flow 171.45 M4 MOUNTING HOLES (4X) IDENTICAL BOTH SIDES 38.10 #8-32 MOUNTING HOLES (4X) MARKED AS Y 171.45 xy xy 177.8 x y 19.05 xy M4 MOUNTING HOLES (4X) MARKED AS X Notes: 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs (0.67 N-m). 2. C ontrol connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. O  utput module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m). 12 advancedenergy.com IMP OPTIONAL CANBUS OR RS485 INTERFACE The RS485/CAN-to-I2C uses 2 Input Protocols and 1 Output Protocol. The Input Protocols used are RS485 using Modbus (Command Index: 0x01), and CAN using modified Modus (Command Index: 0x02). The Output Protocol use is: I2C with SMBus support (Command Index: 0x80). Slave/Server Device(s) Adapter Output Protocols I2C with SMBus Support Adapter Protocol Adapter Command Adapter Controls Input Protocols RS485 using Modbus CAN using Modified Modbus Master/Client Device(s) RS485/CAN - to - I2C For detailed info, download the Software Requirements Specification (SRS) from https://www.artesyn.com/assets/software requirement_specifica_1248401123.pdf iMP CAN RS485 advancedenergy.com 13 ABOUT ADVANCED ENERGY Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes. Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power. For international contact information, visit advancedenergy.com. powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832 Specifications are subject to change without notice. Not responsible for errors or omissions. ©2021 Advanced Energy Industries, Inc. All rights reserved. Advanced Energy®, AE® and Artesyn™ are U.S. trademarks of Advanced Energy Industries, Inc. ENG-IMP-235-01 05.17.21 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Artesyn Embedded Technologies: MP8-3D-2D-1R-00 MP4-2Q-1E-4NN-00 MP4-2Q-2Q-00 MP4-1E-1L-1S-4LF-00 MP4-2Q-1E-1N-1N-0M MP6-2Q1E-1Y-4NN-05 MP4-2E-1L-00 MP4-2Q-00 MP6-2Q-2R-1E-0M MP6-2Q-1L-1E-00 MP6-3E-1Q-00 MP4-2E-1D-4LL00 MP4-1E-1H-1H-1N-00