SIL20C2-00SADJ-VJ

SIL20C2 Series DC-DC CONVERTERS • • • • • • • C Class Non-isolated 4.5 Vin to 13.8 V Single Output PRELIMINARY DATA SHEET February 19, 2005 Preliminary Data - subject to change without notice 1 NEW Product • • 20 a current rating Input voltage range: 4.5-13.8 V Output voltage: 0.59-5.1 V Industry leading value • Cost optimized design excellent transient response Output enable Output voltage adjustability • Pathway for future upgrades • Supports silicon voltage migration • resulting in reduced design-in and qual time Current sink capability roHS compliant The SIL20C2 series is a new high density, open frame, non-isolated converter for space sensitive applications. This model has a wide input range (4.513.8 Vdc) and offers a wide 0.59-5.1 V output voltage range with 20 A load capability. An external resistor adjusts the output voltage from its pre-set value of 0.59 V to any value up to the 5 V maximum. Typical efficiencies for the models are 93% for the 12 V input version. The SIL20C2 series offers remote ON/OFF and over-current protection as standard. All specifications are typical at nominal input, full load at 25 °C, unless otherwise stated OUTPUT SPECIFICATIONS Output voltage Output setpoint accuracy Line regulation Load regulation Min/max load Overshoot Undershoot Ripple and noise 5 Hz to 20 MHz Transient response At turn-on At turn-off (See Note 1) (See Notes 1, 2) (See Note 5) 0.1% trim resistors Low line to high line Full load to min. load 0.59-5.1 V ±1.0% ±0.2% ±0.5% 0 A/20 A 0.5% max. 100 mV max. 30 mV Vin = 5 V, Vout = 2.5 V 130 mV max. deviation 50 µs recovery within regulation band Coplanarity GENERAL SPECIFICATIONS Efficiency Switching frequency Approvals and standards (pending) Material flammability Weight MTBF 12 V @ 40 °C 100% load Bellcore 332 2 year warranty SPECIFICATIONS Vin=5 V, Vo=2.5 V, lo=20 A Fixed 90% 750 kHz EN60950 UL/cUL6950 UL94V-0 8.50 g/0.3 oz. 6,721,853 hours 150 µm ENVIRONMENTAL SPECIFICATIONS Thermal performance (See Note 5) Operating ambient, temperature Non-operating 0 °C to +70 °C -40 °C to +125 °C INPUT SPECIFICATIONS Input voltage range Input current Input current (max.) Start-up time Minimum load Remote OFF (See Note 3) Remote ON/OFF 4.5-13.8 Vdc 50 mA 5 mA 18 A @ Io max. 3 ms PROTECTION Short-circuit Overvoltage protection RECOMMENDED SYSTEM CAPACITANCE Input capacitance (See Note 6) (See Note 7) 0 µF 0 µF Output capacitance Hiccup, non-latching Hiccup, non-latching International Safety Standard Approvals UL/cUL CAN/CSA 22.2 No. E139421 UL60950 File No. TBD TÜV Product Service (EN60950) Certificate No. TBD CB report and certificate to IEC60950 File Name: sil20c2.pdf Rev: 19 Feb 2006 SIL20C2 Series DC-DC CONVERTERS C Class Non-isolated OUTPUT POWER (MAX.) 00 W 1 INPUT VOLTAGE 4.5-13.8 Vdc OVP N/A OUTPUT VOLTAGE 0.59-5.1 V 4.5 Vin to 13.8 V Single Output PRELIMINARY DATA SHEET February 19, 2005 Preliminary Data - subject to change without notice 2 NEW Product For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT CURRENT (MIN.) 0A OUTPUT CURRENT (MAX.) 20 A REGULATION EFFICIENCY (TYP.) LINE LOAD 93% ±0.2% ±0.5% MODEL NUMBER(8, 9) SIL20C2-00SADJ-VJ Part Number System with Options SIL20C2-00SADJ-VJ RoHS Compliance(8) J = Pb-free (RoHS 6/6 compliant) Mounting Option V = Vertical H = Horizontal Output Voltage Single Adjustable Output Input Voltage 00 = 4.5-13.8 V Product Family SIL = Single In Line SMT = Surface Mount Rated Output Current 06 = 6 A 15 = 15 A 20 = 20 A 30 = 30 A 40 = 40 A Performance C = Cost Optimized Generation Blank = Standard Part 2 = Increased Current Density Output Voltage Adjustment of the SIL20C2 Ser ies The ultra-wide output voltage trim range offers major advantages to users who select the SIL20C2. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59-5.1 V. When the SIL20C2 converter leaves the factory, the ouput has been adjusted to the default voltage of 0.59 V. Notes 1 2 3 4 5 6 7 8 9 Measured as per recommended system capacitance. di/dt = 10 A/µs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to full lo and full lo to 0.75. External input fusing is recommended. Additional part numbers may be available with different output voltages. Airflow dependent, 100 LFM minimum required. No capacitor needed for ripple current capability. No capacitor needed for stability. TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please contact your local sales representative for details. NOTICE: Some models may not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/ products.htm to find a suitable alternative. Power Good 4 Enable 5 SIL20C2 Vin 1 7 Vout +Rsense 6 Cin Cout 3 2 8 R L O A D -Rsense Rtrim (for trim down) GND Figure 1: Standard Application Drawing File Name: sil20c2.pdf Rev: 19 Feb 2006 SIL20C2 Series DC-DC CONVERTERS C Class Non-isolated PIN CONNECTIONS PIN NO. 1 2 3 4 5 6 7 8 9 10 FUNCTION Vout Trim Ground Power good Enable Vin Remote Sense (+) Remote Sense (-) *Mech Support *Mech Support 0.050 (1.27) REF 0.462 (11.73) 0.062 (1.57) PCB REF 0.105 (2.67) 4.5 Vin to 13.8 V Single Output PRELIMINARY DATA SHEET February 19, 2005 Preliminary Data - subject to change without notice 3 NEW Product For the most current data and application support visit www.artesyn.com/powergroup/products.htm 0.295 (7.49) 0.610 (15.49) 1.200 (30.48) 0.150 (3.81) TYP PIN 8 0 (0) 0.100 (2.54) 0.200 (5.08) 0.600 (15.24) 0.700 (17.78) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21) PIN 1 0.025 (0.64) ±.001 SQ PIN TYP 8 PLACES * Horizontal and SMT version only Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Figure 2: Vertical Mount Mechanical Drawing 0.482 (12.24) 1.200 (30.48) PIN 9 0.025 (0.64) ±.001 SQ PINS TYP 9 PLACES 0.295 (7.49) 0.062 (1.57) REF 0.610 (15.49) 0.535 (13.59) 0.040 (1.02) REF PIN 1 0.600 (15.24) 0.700 (17.78) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21) 1.165 (29.59) 0.000 (0) 0.100 (2.54) 0.200 (5.08) 0.120 (3.05) TYP 0.125 (3.18) TYP Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Figure 3: Horizontal Mount Mechanical Drawing File Name: sil20c2.pdf Rev: 19 Feb 2006 SIL20C2 Series DC-DC CONVERTERS C Class Non-isolated PIN CONNECTIONS PIN NO. 1 2 3 4 5 6 7 8 9 10 FUNCTION Vout Trim Ground 0.065 (1.65) PIN 8 0.535 (13.59) PIN 10 4.5 Vin to 13.8 V Single Output PRELIMINARY DATA SHEET February 19, 2005 Preliminary Data - subject to change without notice 4 NEW Product For the most current data and application support visit www.artesyn.com/powergroup/products.htm 0.015 (0.38) 1.200 (30.48) PIN 1 0.610 (15.49) 0 (0) 0.100 (2.54) 0.200 (5.08) Enable Vin Remote Sense (+) Remote Sense (-) *Mech Support *Mech Support Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 0.025 (0.64) ±.002 PIN WIDTH TYP 0.482 (12.24) 0.295 (7.49) 0.062 (1.57) PCB REF 0.040 (1.02) 0.125 (3.18) TYP Figure 4: Surface Mount Mechanical Drawing Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: Application Note Longform Datasheet www.artesyn.com File Name: sil20c2.pdf Rev: 19 Feb 2006 0.600 (15.24) 0.700 (17.48) 0.800 (20.32) 0.900 (22.86) 1.050 (26.67) 1.150 (29.21) Power good PIN 9