PD-INC-230VAC-G5V-TTL

PRODIS-INC Digital Process Meter for Incremental Sensors · For ASM Position Sensors and Encoders with incremental output · Integrated sensor supply · Counting rate up to 250 KHz · 6-digit LED display · Relative measurement mode · RS-232 interface · Optional 4 comparator outputs Description PRODIS-INC is designed for use with incremental position sensors to display angles and displacements. The fast counter processes 90° phase shifted A,B signals (quadrature signals) for direction and counting information. Sensor excitation is supplied from the meter. With four membrane keys all parameters can be programmed for the special application. An zero signal and a reference signal can be used for calibration of the measurement system. Optional comparator functions with 4 NPN open-collector outputs are available, 2 of them also as relay output Display 6-digit 7-segment LED, 14 mm high, decimal point programmable 24 V DC ±10% / 150 mA, 85-230 V AC / 180 mA max. 250 kHz maximum, 1 MHz edge frequency 24 V DC/300 mA or 5 V DC/500 mA A, B, Z, T (reference signal) Terminal strip 12-pole, excitation 3-pole -10 ... 40 °C -20 ... 85 °C Approx. 250 g Front IP60, back IP40 95% R.H., non condensing 250 V AC/5 A, 30 V DC/5 A 24 V max./50 mA to GND Directive 73/23/EEC: DIN EN 61010:1994-03 Directive 89/336/EEC Specifications Excitation voltage/current Counting rate Sensor excitation Inputs Connection Operation temperature Storage temperature Weight Protection class Humidity Comparator outputs (option) Relay NPN Electromagnetic compatibility Safety of equipment Order Code PRODIS-INC Model Name Excitation Voltage 24VDC = 24 V DC 230VAC = 230 V AC Sensor Excitation Voltage G24V = 24 V DC G5V = 5 V DC Sensor Signal HTL = HTL level TTL = TTL level Comparator (option) REL2 PD-INC Order Example: PD - INC - 24VDC - G24V - HTL ASM 220503 DAB-PD-INC-E-03 1 PRODIS-INC Digital Process Meter for Incremental Sensors Value range display, offset, limit values -999999 up to +999999 0 up to 59999 Counting direction, decimal point position, last-value memory, Z signal evaluation, display brightness Manual zero, key lock, display value hold, Z release, relative measurement Programmable Parameters / Value Range Divisor, Multiplier Other programmable parameters Signal T Signals Wiring basic equipment Sensor +U B Sensor 0 V (GND) Signal A Signal A Signal B Signal B Signal Z (zero signal) Signal Z (zero signal) Signal T (reference signal) Signal T (reference signal) GND PD-INC-24VDC Excitation +24 V Excitation 0 V PD-INC-230VAC Excitation Protective ground Connector X1 Pin No. 1 2 4 5 6 7 8 9 10 11 12 Connector X2 Pin No. 13 14 13 / 15 14 5 .......1 RS-232 1 ................................12 13 14 15 Rear view without comparator functions PD-INC-24VDC X1 X2 13 14 15 PD-INC-230VAC X1 X2 Level RS-232: ±8 V, galvanically isolated 1 start bit, 8 data bits, 1 stop bit, no parity 4800 / 9600 / 19200 Baud Connector X3 Pin No. 17 16 18 DSUB Connector Pin No. 2 3 5 RS-232 Interface Data format Transmission rate Signals TxD RxD GND 2 DAB-PD-INC-E-03 ASM PRODIS-INC Digital Process Meter for incremental Sensors 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Rear view with comparator functions X4 X3 RS-232 Comparator functions (option) 4 comparator outputs: 1 & 2 = relay and NPN output, 3 & 4 = NPN outputs Signals NPN1 collector NPN2 collector NPN3 collector NPN4 collector NPN GND NPN +UB (24 V) Relay1 NO Relay1 NC Relay1 COM Relay2 NO Relay2 NC Relay2 COM LED 1 is on when relay 1 is in operation LED 2 is on when relay 2 is in operation Connector X4 Pin No. Connector X3 Pin No. 20 21 22 23 24 19 25 27 26 28 30 29 Zero signal Z and reference signal T Valid range ( A & B & Z ) resp. ( A & B & Z & T ) ASM DAB-PD-INC-E-03 3 PRODIS-INC Digital Process Meter for incremental Sensors Outline drawing ASM 48 96 45+0,6 Cut-out according to DIN 43700 nach DIN 43700 Schalttafelausschnitt 92+0,6 PD - INC - 24VDC 9,9 55 8 89,5 9,9 89,5 32 8 PD - INC - 230VAC 4 DAB-PD-INC-E-03 42,4 ASM