VS3-C2-G33-00

1000 - 2500 Watts VS Series VS1-B2-H522-00 1100W total Special Features • Power factor correction • IEC 555-2 harmonic distortion compliance • CISPR 22, EN55022 Level B conducted / radiated EMI • EN61000 immunity standards • European CE Mark • Current share on all outputs • Remote sense on all outputs • Overload protection on all outputs • Voltage adjustment on all outputs • Margining on all outputs • AC-OK-signal (logics “1” or “0”) • Global DC OK (logics “1” or “0”) • DC-OK signal and status indicator LED-on all outputs • Global and individual module inhibits/enable • 3 year warranty • 2500 W with 3-phase input VS3-D2-C2-20 1200W total VS6-L2-00 1500W total Environmental Operating temperature: -10°C to 50°C (derate each output linearly to 60% at 70°C) 40°C max. for reverse air (option #1) Shock/Vibration: Mil-Hdbk 810E Humidity: 95% non-condensing VS8-L9-D9-20 2500W total (case limit) Storage temperature: -55°C to +85°C Temperature coefficient: 0.02% per °C Cooling: Internal DC fan 24V Safety VS4/9 2000 - 2500 W UL CSA VDE CB CE UL60950-1 CSA C22.2 No. 60950-1-03 EN60950 Certificate and report Mark E133211 1 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 AMERICAS 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 EUROPE Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 ASIA Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 VS Series Electrical Specs Input Fuse rating Input voltage 600 V / 25 A (internal)1Ø 250 V / 20 A (internal)3Ø 85-264 VAC 1Ø VS1, VS3 & VS4 (See operating curve) Output Adjustment range Margining Line/load reg Ripple ±10% minimum ±4-6% nominal 0.2% or 5 mV max. RMS: 0.1% or 10 mV P-P: 1.0% or 50 mV Bandwidth limited to 20 MHz 2% or 100 mV with 25% load step (any output) To within 1% in 1 Megohm 180-264 VAC 3Ø VS6, VS8 & VS9 Frequency Inrush current Efficiency Power factor Turn-on time EMI-filter Leakage current Holdover storage AC-OK warning time Loss of phase 47 to 440 Hz 40 A peak max. 75% - 82% 0.99 typical (0.9 on VS6, VS8 & VS9) AC / 1 sec; Inhibit / 100 ms max. CISPR 22, EN55022 Level B conducted/radiated 2 mA max. at 240 VAC 20 ms min. / 40 ms typical independent of VAC >5 ms (power fail) On VS6, VS8 & VS9, unit will continue to operate with loss of phase Remote sense Single wire parallel Switching frequency DC OK Output/Output isolation Dynamic response Recovery time Overvoltage protection Overload protection Short circuit protection Reverse voltage protection Thermal protection Input Operating Curve 2200 2000 MAXIMUM OUTPUT POWER (W) 1800 1600 1400 1200 1000 800 600 400 200 0 80 100 120 140 160 180 200 220 240 INPUT AC VOLTAGE (VAC) @ 50/60Hz Single Phase www.astecpower.com 69-825-410 Rev C 12.01.04 260 2 Common Examples and Specifications Case size 1 = 5 inch, 2 slot, 3 = 8 inch, 4 slot, 4 = 11 inch, 6 slot, 6 = 5 inch, 2 slot, 8 = 8 inch, 4 slot, 9 = 11 inch, 6 slot, 1500 W max 1Ø 2000 W max 1Ø 2000 W max 1Ø 1500 W max 3Ø 2500 W max 3Ø 2500 W max 3Ø (Same for Each Slot) Option Codes 0 = no options 1 = rear air exhaust (40°C max.) 3 = set unit for global enable 5 = options 1 & 3 USE ONLY-FOR MODIFIED STANDARD, CONSULT-FACTORY Indicates CE compliance Output Module Code A = 300 W single 1 slot B = 600 W single 1 slot C = 900 W single 2 slots D = 1200 W single 2 slots E = 250 W dual 1 slot F = 250 W triple 1 slot G = 500 W dual 1 slot H = 500 W triple 1 slot K = 750 W single 1 slot L = 1500 W single 2 slot Output Voltage Code 0 = 2V 1 = 3.3 V 2= 5V 3 = 12 V 4 = 15 V 5 = 24 V 6 = 28 V 7 = 36 V 8 = special voltage (consult factory) 9 = 48 V Configuration Rules 1. Omit digits that do not apply. 2. a. Specify modules from lowest number of outputs to highest. b. If number of outputs are equal, specify from highest to lowest power increments. c. If power increments are equal, specify from highest to lowest current. 3. All model configurations created using this selection guide represent standard products with standard availability and lead times. 4. If slots are left empty, a blank panel will be automatically installed. Parallel Code VS1 and VS6 available slots J1 SLOT 2 SLOT 1 VS3 and VS8 available slots N SLOT 4 SLOT 3 SLOT 2 SLOT 1 VS4 and VS9 available slots N J1 SLOT 3 SLOT 2 SLOT 6 SLOT 5 SLOT 4 SLOT 1 Parallel Codes 0 = no parallel 1=1&2 2=2&3 3=3&4 4=1&2 &3 5=2&3 &4 6=1&2+3&4 7=1&2&3&4 8=3&4+5&6 J1 Example (more on next page): VS 1 - K 2 - G 3 3 - 0 0 - CE No options Slot 1 1: 5V @ 150A Slot 2 2: 12V @ 21A 3: 12V @ 20A No paralleling 5 inch case (2 slots available) Output Current Output Voltage Identification Output Voltage Code 0 1 2 3 4 5 6 7 9 Output Voltage 2V 3.3 V 5V 12 V 15 V 24 V 28 V 36 V 48 V 9=1&2+3&4+5&6 Module Identification A (1 slot) 300 W Single 60 A 60 A 60 A 25 A 20 A 12.5 A 10.7 A 8.3 A 6.3 A B (1 slot) 600 W Single 120 A 120 A 120 A 50 A 40 A 25 A 21.4 A 16.6 A 12.5 A C (2 slots) 900 W Single 180 A 180 A 180 A 75 A 60 A 37.5 A 32.1 A 24.9 A 18.75 A D (2 slots) 1200 W Single 240 A 240 A 240 A 100 A 80 A 50 A 42.8 A 33.2 A 25 A E, F (1 slot) 250 W Multi Main Output 25 A 25 A 25 A 10.5 A 8.3 A 5.3 A 4.5 A N/A N/A G, H (1 slot) 500 W Multi Main Output 50 A 50 A 50 A 21 A 16.6 A 10.5 A 9A N/A N/A K (1 slot) 750 W Single 150 A 150 A 150 A 62.5 A 50 A 31.2 A 26.7 A 20.8 A 15.6 A L (2 slots) 1500 W Single 300 A 300 A 300 A 125 A 100 A 62.4 A 53.4 A 41.6 A 31.2 A Note: Increments of current not shown can be achieved by paralleling modules (add currents of each module selected). Auxiliary Output Table: Output(s) 2 and/or 3 of Module Voltage Identification Output Voltage Code 0 1 2 3 4 5 6 Output Voltage 2V 3.3 V 5V 12 V 15 V 24 V 28 V Module Identification E 250 W Dual Aux. Output 10 A 10 A 10 A 10 A 10 A 5A 5A F 250 W Triple Aux. Output 5A 5A 5A 5A 5A 2.5 A 2.5 A G 500 W Dual Aux. Output 20 A 20 A 20 A 20 A 20 A 10 A 10 A H 500 W Triple Aux. Output 10 A 10 A 10 A 10 A 10 A 5A 5A 3 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 AMERICAS 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 EUROPE Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 ASIA Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 EXAMPLES Examples of Model Numbers - SINGLE OUTPUTS Total Power 600 W 750 W 900 W 1200 W 1200 W 1500 W 2000 W 2500 W Volts / Amps 5 V / 120 A 12 V / 62.5 A 5 V / 180 A 5 V / 240 A 2 V / 600 A 15 V / 100 A 5 V / 400 A 48 V / 52 A Size (H x W x L) 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 8 x 11 5 x 5 x 11 5 x 8 x 11 5 x 8 x 11 Model Number VS1-B2-00 VS1-K3-00 VS1-C2-00 VS1-D2-00 VS3-L0-L0-20 VS1-L4-00 VS3-D2-C2-20* VS8-L9-D9-20 ** Other Voltages Available 2V 3.3 V 5V 12 V 15 V 24 V 28 V 36 V Special 48 V VS Series Voltage ID Code 0 1 2 3 4 5 6 7 8 (consult factory) 9 * D2 module derated to 1100 W (2000 W max.) **D9 module derated to 1000 W (2500 W max ) Examples of Model Numbers - MULTIPLE OUTPUTS Total Power 500 W 750 W 800 W 800 W 800 W 800 W 990 W 1000 W 1000 W 1100 W 1100 W 1100 W 1100 W 1100 W 1400 W 1400 W 1440 W 1600 W 1680 W 1700 W 1900 W 2000 W 2000 W 2500 W Output 1 5 / 50 5 / 50 5 / 60 5 / 60 5 / 60 5 / 60 5 / 150 5 / 50 5 / 50 5 / 120 5 / 120 5 / 170 5 / 120 5 / 120 5 / 180 5 / 180 5 / 240 5 / 170 5 / 240 5 / 240 5 / 180 5 / 300 5 / 240 5 / 300 Output 2 12 / 10 12 / 10 12 / 21 12 / 21 15 / 16.6 15 / 16.6 2 / 120 12 / 10 12 / 10 12 / 21 12 / 21 12 / 10 15 / 16.6 15 / 16.6 12 / 21 12 / 21 2 / 120 12 / 20 2 / 240 12 / 21 12 / 21 12 / 21 12 / 21 3.3 / 120 Output 3 12 / 10 12 / 10 12 / 10 12 / 10 15 / 10 15 / 10 12 / 10 12 / 10 12 / 20 12 / 10 12 / 10 15 / 10 15 / 10 12 / 20 12 / 10 12 / 21 12 / 20 12 / 20 12 / 10 12 / 20 12 / 21 Output 4 15 / 8.3 5 / 10 24 / 5 5 / 10 24 / 5 15 / 16.6 15 / 16.6 5 / 10 5 / 10 24 / 5 5 / 10 5 / 20 5 / 50 5 / 10 5 / 60 12 / 10 15 / 10 15 / 10 15 / 10 24 / 5 24 / 5 Output 5 15 / 5 Output 6 5/5 Size 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 5 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 5 x 8 x 11 Model Number VS1-H233-00 VS1-H233-F442-00 VS1-A2-H332-00 VS1-A2-H335-00 VS1-A2-H442-00 VS1-A2-H445-00 VS1-K2-B0-00 VS1-H233-H445-00 VS1-H233-H425-00 VS1-B2-G33-00 VS1-B2-H332-00 VS1-B2-H233-10 VS1-B2-H442-00 VS1-B2-H445-00 VS3-C2-G33-00 VS3-C2-H332-00 VS3-D2-B0-00 VS3-B2-G23-G32-10 VS3-D2-D0-00 VS3-D2-G33-00 VS3-C2-G33-H245-00 VS3-L2-H332-00 VS3-D2-G33-H245-00 VS8-L2-B1-H334-00 15 / 10 5 / 10 24 / 5 24 / 5 Pin Assignments PFC J1 CONTROL CONNECTOR Pin No. Function J1-1 AC OK Logic 1 J1-2 AC OK Logic 0 J1-3 Global DC OK/Conv Run Logic 1 J1-4 Global DC OK/Conv Run Logic 0 J1-5 Global DC OK/Conv Run/AC OK Return J1-6 Global Inhibit Logic 0*/ENA Logic '0' J1-7 Global Inhibit Logic 1*/ENA Logic '1' J1-8 Global Inhibit Return*ENA RTN J1-9 Global Isolated Inhibit J1-10 Global Isolated Inhibit Return * Changes to Enable with Option Code 3 Multiple Output J1 CONTROL CONNECTOR Pin No. Function J1-1 V1 +Remote Sense J1-2 V1 Remote Margin / V. Program J1-3 V1 Remote Margin Hi J1-4 V1 -Remote Sense / Margin Lo J1-5 V1 DC OK / Conv Run Logic 1 J1-6* V1 Isolated Inhibit J1-7 V1 DC OK / Conv Run / ISO Inh. Return J1-8 V1 Single Wire Parallel J1-9 V2 Single Wire Parallel J1-10 V3 Single Wire Parallel * Inhibits off all the outputs within that module. J2 CONTROL CONNECTOR Pin No. Function J2-1 V2 +Remote Sense J2-2 V2 Remote Margin / V. Program J2-3 V2 Remote Margin Hi J2-4 V2 -Remote Sense / Margin Lo J2-5 V2 DC OK /Logic 1 J2-6 V3 +Remote Sense J2-7 V3 Remote Margin / V. Program J2-8 V3 Remote Margin Hi J2-9 V3 -Remote Sense J2-10 V3 DC Good /Logic 1 Single Output J1 CONTROL CONNECTOR Pin No. Function J1-1 +Remote Sense J1-2 Remote Margin / V. Program J1-3 Remote Margin Hi J1-4 -Remote Sense / Margin Lo J1-5 DC OK / Conv Run Logic 1 J1-6 Isolated Inhibit J1-7 DC OK / Conv Run / ISO Inh. Return J1-8 Single Wire Parallel J1-9 Spare Pin J1-10 Spare Pin Notes: Electrical Characteristics 1. 2. 3. DC OK minus 2 to 6% of nominal output voltage (tracking). Inhibit & Enable are both TTL compatible. ISOLATED requires 2 mA source, typical. DC OK/Converter Run denotes output voltage is present and converters are running (Or'ed signal configuration). PFC LED: Red = Bulk DC bus voltage low; Green = Bulk DC OK. Output LED: Red = Indicated output not operating within tolerance; Green = Indicated output operating within tolerance. The 5 x 5 x 11 (VS1/6) case is power limited to 1500W max. See operating curve. The 5 x 8 x 11 case and 5 x 11 x 11 case (VS3/4) are power limited to 2000W max. The VS8/9 cases are power limited to 2500W max. Specifications subject to change without notice. Warranty: 3 yrs 4. 5. 6. 7. 8. 9. www.astecpower.com 69-825-410 Rev C 12.01.04 4 Drawings VS1 & VS6 • 1000-1500 WATTS 5-inch Case Size (5” x 5” x 11”) VS1 Input Module AC High Neutral Ground 5.00 ± 0.05 STD AIR FLOW .94 MAX 23.89) 11.00 ± .05 (279.31 ± 1.27) 1.2 8-32 UNC-2B Threaded Insert, 4 Places Like Pattern Opposite Side Max penetration: 0.150 (3.81 ) SLOT 2 SLOT 1 5.00 Max (127.03) Side 4.000 ± .020 (101.60 ± .50) J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .05 (88.65 ± 1.27) .500 ± .050 (12.70 ± 1.27) AC Main Input 6.750 ± .020 (171.45 ± .50) .27 ± .05 (6.86 ± 1.27) .750 ± .050 (19.05 ± 1.27) Bottom 8-32 UNC-2B Threaded Insert, 4 Places Max penetration: 0.150 (3.81) VS6 Input Module AC Phase A AC Phase B AC Phase C 5.00 ± 0.05 SLOT 2 SLOT 1 6.750 ± .020 (171.45 ± .50) AC Ground N 5.00 Max (127.03) Back J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .05 (88.65 ± 1.27) .750 ± .050 (19.05 ± 1.27) 4.000 ± .020 (101.60 ± .50) .500 ± .050 (12.70 ± 1.27) NOTES (ALL MODELS) 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). For VS1, VS3 & VS4 additional GND CONN added for VS6, VS8 & VS9. Max torque: 10 in-lbs (1.1 N-m). 2. Control connectors: (J1 and J2) 10 position Molex 90130-3210 housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. 3. Output terminals (A-300 W) (B-600 W) & (K-750 W) single modules: two (2) 10-32 UNF HEX HD BOLTS. Max. torque: 25 in-lbs (2.78 N-m). 4. Output terminals (E/F-250 W) & (G/H-500 W) dual/triple modules: Primary: two (2) 10-32 UNF HEX HD BOLTS. Max. torque: 25 in-lbs (2.78 N-m). Secondary: barrier strip two (2) 6-32 UNC screws (0.375” centers) per output. Max torque: 10 in-lbs (1.1 N-m). 5. Output terminals (C-900 W) (D-1200 W) & (L-1500 W) single modules: four 5/16-18 x 5/8" hex head cap screws. Max. torque: 120 in-lbs (13.35 N-m). Captive lock washer provided. 6. Chassis material: aluminum with chemical film coating. 7. Adjustment access: voltage, power fail, and overcurrent from front panel. 8. Bar code: code 39 extended. 9. Mounting for 5-inch & 8-inch case: four(4) 8-32 clinch nuts on three (3) surfaces. Mounting for 11-inch case: four (4) 8-32 clinch nuts on two (2) side surfaces & six (6) 8-32 clinch nuts on bottom surface. Max. penetration 0.150 inch (3.81). Max. torque: 15 in-lbs (1.67 N-m). 10. Additional support is recommended when unit is mounted in a suspended configuration. Mounting clinch nuts are not designed to support the weight of the unit. 11. Fans: 5-inch case, (1) 4.5" dia, 112 CFM (no load), 49 dBA. 8-inch case, (1) 4.5" dia, 112 CFM (no load), 49 dBA; (2) 2.25” dia, 23 CFM (no load), 38 dBA. 11-inch case, (2) 4.5" dia, 112 CFM (no load), 49dBA 12. All dimensions are in inches (mm). 13. Specifications subject to change without notice. 5 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 AMERICAS 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 EUROPE Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 ASIA Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 8-inch Case Size (5” x 8” x 11”) (18 lbs. / 8.2 kg. maximum) VS3 Input Module AC High Neutral Ground 7.90 ± 0.05 (200.66 ± 1.27) DRAWINGS • VS3 & VS8 • 1000-2500 WATTS VS Series .94 MAX 23.89) 11.00 ± .05 (279.31 ± 1.27) 1.2 STD AIR FLOW 8-32 UNC-2B Threaded Insert, 4 Plac Like Pattern Opposite S Max penetration: 0.150 SLOT 4 SLOT 3 SLOT 2 SLOT 1 5.00 MAX (127.03) Side 4.000 ± .020 (101.60 ± .50) J1 2.04 ± .05 (51.82 ± 1.27) 3.49 ± .10 (88.65 ± 2.54) 4.94 ± .10 (125.48 ± 2.54) 6.39 ± .10 (162.31 ± 2.54) 6.750 ± .020 (171.45 ± .50) .27 ± .05 (6.86 ± 1.27) .500 ± .050 (12.70 ± 1.27) .750 ± .050 (19.05 ± 1.27) AC Main Input Bottom Back VS8 7.90 ± 0.05 (200.66 ± 1.27) AC Phase A AC Phase B AC Phase C 6.750 ± .020 (171.450 ± .50) 1.2 .750 ± .050 (19.05 ± 1.27) 8-32 UNC-2B Threaded Insert, 4 Places Max penetration: 0.150 (3.81) SLOT 4 SLOT 3 SLOT 2 SLOT 1 AC Ground N 5.00 MAX (127.03) Input Module J1 2.04 ± .05 (51.82 ± 1.27) 1.067 ± .050 (27.099 ± 1.270) 5.750 ± .020 (146.050 ± .508) 3.49 ± .10 (88.65 ± 2.54) 4.94 ± .10 (125.48 ± 2.54) 6.39 ± .10 (162.31 ± 2.54) www.astecpower.com 69-825-410 Rev C 12.01.04 6 Drawings VS4 & VS9 • 2000-2500 WATTS 1.2 11-inch Case Size (5” x 11” x 11”) VS4 10.80 ±.20 274.32 ±5.04 (PFC) 8-32 UNC-2B THREADED INSERT, 6 PL AC HIGH NEUTRAL GROUND ~ N S L S L O T 5 S L O T 4 S L O T 3 S L O T 2 S L O T 1 5.00 127.0 MAX 6.750 171.450 ±.02 ±.50 ~ O P/F .52 13.1 INTERNAL FUSE 25 AMPS/600V T 6 61 .750 19.050 ±.05 ±1.270 J1 .33 8.3 2.04 ±.10 51.81 ±2.54 3.49 ±.10 88.64 ±2.54 DETAIL A 4.94 ±.10 125.47 ±2.54 6.39 ±.10 162.31 ±2.54 7.84 ±.10 199.14 ±2.54 9.29 ±.10 235.97 ±2.54 1.067 ±.050 27.099 ±1.270 5.750 ±.020 146.050 ±.508 8.750 ±.020 222.25 ±.508 VS9 1.2 .94 MAX 23.89 11.00 ±.05 279.31 ±1.27 8-32 UNC-2B THREADED INSERT, 4 PL LIKE PATTERN OPPOSITE SIDE 10.80 ±.20 274.32 ±5.04 (PFC) AC Phase A AC HIGH AC Phase B NEUTRAL AC GROUND Phase C STD AIR FLOW FRONT AIR EXHAUST 4.00 ±.02 101.60 ±.50 ~ N S L S L O T 5 S L O T 4 S L O T 3 S L O T 2 S L O T 1 5.00 127.0 MAX ~ O P/F .52 13.1 INTERNAL FUSE 25 AMPS/600V T 6 61 MAX OPTIONAL REAR AIR EXHAUST J1 .33 8.3 2.04 ±.10 51.81 ±2.54 3.49 ±.10 88.64 ±2.54 .50 ±.05 12.70 ±1.27 6.75+.02 171.45 +.50 .27 ±.05 6.86 ±1.27 .75 ±.05 19.05 ±1.27 DETAIL A 4.94 ±.10 125.47 ±2.54 6.39 ±.10 162.31 ±2.54 7.84 ±.10 199.14 ±2.54 9.29 ±.10 235.97 ±2.54 7 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 69-825-410 Rev C 12.01.04 www.astec.com Module Front Panels .60 15.24 ?.050 ?1.27 1.03 ?.050 26.21 ?1.27 + + .66 16.80 ?.050 ?1.27 J1 .66 16.80 ?.050 ?1.27 1.00 25.40 ?.050 ?1.27 .60 15.24 ?.050 ?1.27 PH PH PH + .52 13.1 .52 13.1 .52 13.1 J2 .33 8.3 1.442 REF 250W/500W DUAL/TRIPLE OUTPUT (1 SLOT) MODULE CODES E = 250W DUAL F = 250W TRIPLE G = 500W DUAL H = 500W TRIPLE .33 8.3 1.442 REF 300W/600W/750W SINGLE OUTPUT (1 SLOT) MODULE CODES A = 300W B = 600W K = 750W 2.77 70.3 3.70 94.16 ?.050 ?1.27 + + 3.70 94.16 ?.050 ?1.27 .52 13.1 J1 1.79 45.5 2.874 REF J1 DETAIL A 900W/1200W/1500W SINGLE OUTPUT (2 SLOTS) MODULE CODES C = 900W D = 1200W L = 1500W AMERICAS 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 1.38 ?.050 34.94 ?1.27 2.31 ?.050 58.59 ?1.27 1.442 REF EUROPE Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 BLANK (1 SLOT) ASIA Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 69-825-410 Rev C 12.01.04 153