AT697E-2E-E

Features • Smart Card Interface – Compliance with Standards • ISO/IEC 7816-1, 2, 3 and 4 • EMV 2000 • CB • Mondex®, Proton, ZKA, Other: Contact Gemplus® – Supported Smart Cards • Number of Smart Cards Supported: 1 • Asynchronous Cards: T=0 and T=1 • Synchronous/Memory Cards Using a Command Interpreter • EMV or Non EMV Cards Electrical Interface • Transmission Speed: 9.6 Kbps to 115 Kbps • Card Power Supply: 1.8V/3V/5V • ESD Protection On Card Pins: 4 KV - Human Body Model • Card Presence or Insertion Detection • Short Circuit Current Limitation Host Interface – Physical Layer • Serial Asynchronous Link • Programmable Transmission Speed From 1,200 bps to 115,200 bps • Format: 8 bits, No Parity, 1 Stop Bit • Adjustable Signal Voltage – Protocol • Gemplus Block Protocol (GBP) • GBP Interface Library Kit Source Code Chip Power Supply – Voltage: VCC- 2.85V to 5.4V – Consumption: 8 mA Typical, 150 mA Max - Smart Card Powered – Power Down Mode • 100 µA Max Power Down Current • Power-down/Power-up by Host Command Additional Features – Operating Temperature Range: 0° to +70° (-40° to +85° C C C C) – Package: SS0P24, QFN32 – LED Management: The LED is On When the Card is Powered On • GemCore Serial Lite PRO AT83C21GC Summary • • • Description AT83C21GC is designed to simplify the integration of smart card interfaces in electronic devices. It manages the electrical interface and communication with ISO 7816 –1/2/3/4 compatible smart cards and memory cards. Figure 1. Basic Architecture of a Smart Card Reader Host Processor AT83C21GC Smart Card Smart Card Connector 4247DS–SCR–03/07 This is a summary Document. A complete document is available on the Gemplus Web site. www.gemplus.com The connection with the host processor is achieved via a serial asynchronous link; the rate can be selected from a range from 1200 to 115,200 bps. The software inside the GemCore chip handles a communication protocol with the host system called the Gemplus Block Protocol (GBP). A complete set of documentation is available on the Gemplus web site: http://www.gemplus.com. A GBP Interface Library Kit can be provided, upon request. It consists of the source code of the GBP communication layer between the host and GemCore. It is written in the C language. See the Gemplus developers’ site at www.gemplus.com. Enquiries can also be posted to cardreader@atmel.com. For general information on the device, please refer to the AT83C5121 datasheet available on the Atmel web site, www.atmel.com. 2 AT83C21GC 4247DS–SCR–03/07 AT83C21GC Ordering information Part Number AT83C21GCxxx-ICSIL AT83C21GCxxx-ICRIL AT83C21GCxxx-ICSUL AT83C21GCxxx-ICRUL AT83C21GCxxx-PUTUL AT83C21GCxxx-PURUL Temperature Range Industrial Industrial Industrial & Green Industrial & Green Industrial & Green Industrial & Green Package SSOP24 SSOP24 SSOP24 SSOP24 QFN32 QFN32 Packing Stick Tape & Reel Stick Stick Tray Tape & Reel xxx : Firmware version 3 4247DS–SCR–03/07 Pin Description Figure 2. 24-pin SSOP Pinout CVSS LI CVCC P1.5/CRST P1.4/CCLK P1.3/CC4 P1.2/CPRES P1.1/CC8 P1.0/CIO RST XTAL2 1 2 3 4 5 6 7 8 9 10 11 12 SSOP24 24 23 22 21 20 19 18 17 16 15 14 13 VCC EVCC DVCC VSS P3.0/RxD P3.1/TxD P3.3/INT1/OE P3.4/T0 P3.2/INT0 P3.5/CIO1/T1 P3.6/CCLK1/LED0 P3.7/CRST1/LED1 XTAL1 Figure 3. 32-pin QFN Pinout CVss Vcc EVcc DVcc N/C LI N/C 32 31 30 29 28 27 26 25 CVcc P1.5/CRST P1.4/CCLK P1.3/CC4 P1.2/CPRES P1.1/CC8 P1.0/CIO RST 1 2 3 4 5 6 7 8 N/C N/C QFN32 24 23 22 21 20 19 18 17 Vss Vss P3.0/RxD P3.1/TxD P3.3/INT1/OE P3.4/T0 P3.2/INT0 P3.5/CIO1/T1 9 10 11 12 13 14 15 16 P3.7/CRST1/LED1 P3.6/CCLK1/LED0 N/C N/C XTAL2 XTAL1 N/C Table 1. Port Signal Description Internal Port P1.0 Signal Name CIO Power Supply CVCC ESD 4 kV Type I/O Description Smart Card Interface Function Card I/O – Pull-up medium is lower than 20KΩ Smart Card Interface Function Card contact 8 – Pull-up medium must be less than 20KΩ Smart Card Interface Function Card presence P1.1 CC8 CVCC 4 kV I/O P1.2 CPRES VCC 4 kV I 4 AT83C21GC 4247DS–SCR–03/07 AT83C21GC Table 1. Port Signal Description (Continued) Internal Port P1.3 Signal Name CC4 Power Supply CVCC ESD 4 kV Type I/O Description Smart Card Interface Function Card contact 4 – Pull-up medium must be less than 20KΩ Smart Card Interface Function Card clock Smart Card Interface Function Card reset – Pull-up medium must be less than 20KΩ UART Function Receive data input UART Function Transmit data output. Input/Output Function P3.2 is a bi-directional I/O port with internal pull-ups. Input/Output Function P3.3 is a bi-directional I/O port with internal pull-ups. Input/Output Function P3.4 is a bi-directional I/O port with internal pull-ups. Alternate Card Function Card I/O: Pull-up medium must be less than 20K LED function P3.6 CCLK1 DVCC O These pins can be directly connected to the cathode of the standard LED without external current limiting resistors. The typical current of each output can be programmed by software to 2, 4 or 10 mA (LEDCON register). Input/Output Function P3.7 is a bi-directional I/O port with internal pull-ups. Reset Input Holding this pin low for 64 oscillator periods while the oscillatoris running resets the device. The Port pins are driven to their reset conditions when a voltage lower than VIL is applied, whether or not the oscillator is running. This pin has an internal pull-up resistor which allows the device to be reset by connecting a capacitor between this pin and VSS. Asserting RST when the chip is in Idle mode or Power-down mode returns the chip to normal operation. The output is active for at least 12 oscillator periods when an internal reset occurs. XTAL1 VCC I Input to the on-chip Inverting Oscillator Amplifier To use the internal oscillator, a crystal/resonator circuit is connected to this pin. If an external oscillator is used, its output is connected to this pin. XTAL2 VCC O Output of the on-chip Inverting Oscillator Amplifier To use the internal oscillator, a crystal/resonator circuit is connected to this pin. If an external oscillator is used, XTAL2 may be left unconnected. VCC PWR Supply Voltage VCC is used to power the internal voltage regulators and internal I/O’s. LI PWR DC/DC Input LI must be tied to VCC through an external coil (typically 4, 7 µH) and provide the current for the pump charge of the DC/DC converter. P1.4 CCLK CVCC 4 kV O P1.5 CRST CVCC 4 kV O P3.0 RxD EVCC I P3.1 TxD EVCC O P3.2 INT0 DVCC I/O P3.3 INT1 EVCC I/O P3.4 EVCC I/O P3.5 CIO1 DVCC I/O P3.7 RST CRST1 DVCC VCC I/O I/O 5 4247DS–SCR–03/07 Table 1. Port Signal Description (Continued) Internal Port CVCC Signal Name Power Supply ESD Type PWR Description Card Supply Voltage CVCC is the programmable voltage output for the Card interface. It must be connected to an external decoupling capacitor. DVCC PWR Digital Supply Voltage DVCC is used to supply the digital core and internal I/Os. It is internally connected to the output of a 3V regulator and must be connected to an external decoupling capacitor. EVCC VCC PWR Extra Supply Voltage EVCC is used to supply the level shifters of UART interface I/O pins. It must be connected to an external decoupling capacitor. This reference voltage is generated internally (automatically or not), or it can be connected to an external voltage reference. CVSS GND DC/DC Ground CVSS is used to sink high shunt currents from the external coil. VSS GND Ground 6 AT83C21GC 4247DS–SCR–03/07 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise,to anyintellectualproperty right is granted by this document or in connection with the sale of Atmel products. E XCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORYWARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULARPURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUTOF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes norepresentationsor warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specificationsand product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for useas components in applications intended to support or sustainlife. ©2007 Atmel Corporation . A ll rights reserved. A tmel®, logo and combinations thereof, are registered trademarks, and Everywhere You Are ® are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4247DS–SCR–03/07