AT85C51SND3BX

Active AT85C51SND3Bx Errata List • • • • • • I/O Ports – P0, P2, P4, P5 Read-Modify-Write SIO Interface – Low Baudrate Data Reception Ready Report SPI Interface – DFC Usage Limitation Battery Monitor – Bad Conversion Linearity ISP – ISP Entry When Blanked Nand Flash ISP – ISP USB enumeration on Windows™ XP AT85C51SND3Bx Errata History Lot Number All Errata List 1, 2, 3, 4, 5, 6 MP3 Microcontrollers AT85C51SND3Bx AT85C51SND3Bx Errata Description 1. I/O Ports – P0, P2, P4, P5 Read-Modify-Write The P0, P2, P4, P5 implementation may lead to Input lock-up when using readmodify-write (RMW) instructions: ANL ORL XRL JBC CPL INC DEC DJNZ MOV PX.Y,C CLR PX.Y SETB PX.Y – – – (logical AND, e.g., ANL P2,A) (logical OR, e.g., ORL P2,A) (logical EX-OR, e.g., XRL P2,A) (jump if bit set and clear bit, e.g., JBC P2.1, LABEL) (complement bit, e.g., CPL P2.0) (increment, e.g., INC P2) (decrement, e.g., DEC P2) (decrement and jump if not zero, e.g., DJNZ P2, LABEL) (move carry bit to bit Y of Port X) (clear bit Y of Port X) (set bit Y of Port X) Errata Sheet Here is a normal I/O port RMW execution sequence: Read the I/O port SFR (latch) Modify the data Write back the modified data to port SFR Now here is what is really executed, these instructions that should read the internal latch read in fact the port data: – – – Read the I/O port data Modify the data Write back the modified data to port SFR Here is a detailed example: P0.0 is used as input (set low by external hardware) while other P0 I/O are used as output. Following code may set P0.1 and leave other bits unaffected: setb P0.1; – before executing, P0 SFR= 1111 1101; P0 port= 1111 1100 7656A–MP3–04/07 – after executing, P0 SFR= 1111 1110; P0 port= 1111 1110 Now P0.0 is no more programmed as input. The latch content is set to 0 meaning the port is internally driven to low level like for an output. Workaround To avoid any conflict with port inputs, put all application inputs on same port. If this is not possible, avoid using RMW instructions and rebuild such instruction by software by taking care to set the Port SFR bit to 1 when writing back to SFR. 2. SIO Interface – Low Baudrate Data Reception Ready Report RI flag reset time too long after reading data into the reception FIFO. This may report bad data reception and lead to double read of received characters. This errata depends on the CPU frequency and the treatment done on the received character, it appears using polling mode and using low baudrate values. Workaround The goal of the workaround is to leave enough time to the RI flag to be reset to forbid a bad reception (RI=1) detection. Two workaround are proposed: – – Limit the baudrate to high values, e.g. > 50Kbaud with Fosc= 12MHz, X2 mode and 12x oversampling factor. Add a delay between two reads of a character. 3. SPI Interface – DFC Usage Limitation DFC transfers to SPI do not operate properly when DFC is clocked by PLL. Workaround Use DFC transfer only with DFC clocked by oscillator. 4. Battery Monitor – Bad Conversion Linearity Battery monitor reports bad linearity data. Workaround Use the VB4:0 value as threshold voltage conversion only, do not use it for full range voltage conversion. 5. ISP – ISP Entry When Blanked Nand Flash The ISP mode is not automatically started when first powered-up with new blanked Nand Flash. This case specially appears when in production. Workaround Use a key of the keyboard matrix to force ISP entry at power-up. This is achieved by connecting any column sig- nal to ISP pin. Then pressing the key connected to this column and to ROW 0 will assert the ISP pin. Note that this workaround forbids debug mode as ISP pin is also the OCDT pin. Solution is to add a 0 Ω resistor in order to insulate the OCDT pin from the keypad during debugging. For an example on how to apply the workaround, refer to the at85rfd-07 schematic. 2 7656A–MP3–04/07 6. ISP – ISP USB enumeration on Windows™ XP When connecting the device to windows XP, an informational pop-up is opened near the status bar: This is a windows dummy message since ISP is done in full speed mode. Workaround None. Do not take care of this pop-up. 3 7656A–MP3–04/07 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Literature Requests www.atmel.com/literature Disclaimer: A tmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. © 2007 Atmel Corporation. All rights reserved. A tmel®, logo and combinations thereof, Everywhere You Are ® a nd others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 7656A–MP3–04/07