AT88SC0204CA-Y6H-T

Features • One of a Family of Devices with User Memories from 1-Kbit to 8-Kbits • 2-Kbit (256-byte) EEPROM User Memory ⎯ Four 512-bit (64-byte) Zones ⎯ Self-timed Write Cycle ⎯ Single Byte or 16-byte Page Write Mode ⎯ Programmable Access Rights for Each Zone • 2-Kbit Configuration Zone ⎯ 37-byte OTP Area for User-defined Codes ⎯ 160-byte Area for User-defined Keys and Passwords • High Security Features ⎯ 64-bit Mutual Authentication Protocol (Under License of ELVA) ⎯ Cryptographic Message Authentication Codes (MAC) ⎯ Stream Encryption ⎯ Four Key Sets for Authentication and Encryption ⎯ Eight Sets of Two 24-bit Passwords ⎯ Anti-Tearing Function ⎯ Voltage and Frequency Monitors • Smart Card Features ⎯ ISO 7816 Class B (3V) Operation ⎯ ISO 7816-3 Asynchronous T=0 Protocol (Gemplus® Patent) * ⎯ Multiple Zones, Key Sets and Passwords for Multi-application Use ⎯ Synchronous 2-wire Serial Interface for Faster Device Initialization * ⎯ Programmable 8-byte Answer-To-Reset Register ⎯ ISO 7816-2 Compliant Modules • Embedded Application Features ⎯ Low Voltage Supply: 2.7V – 3.6V ⎯ Secure Nonvolatile Storage for Sensitive System or User Information ⎯ 2-wire Serial Interface (TWI, 5V Compatible) ⎯ 1.0 MHz Compatibility for Fast Operation ⎯ Standard 8-lead Plastic Packages, Green compliant (exceeds RoHS) ⎯ Same Pin Configuration as AT24CXXX Serial EEPROM in SOIC and PDIP Packages • High Reliability ⎯ Endurance: 100,000 Cycles ⎯ Data Retention: 10 years ⎯ ESD Protection: 2,000V min CryptoMemory® AT88SC0204CA Summary * Note: Modules available with either T = 0 / 2-wire modes or 2-wire mode only. 5202ES–CRYPT–08/09 Table 1. Pad VCC GND Pin Assignments Description Supply Voltage Ground ISO Module C1 C5 C3 C7 C2 TWI Module C1 C5 C3 C7 NC “SOIC, PDIP” 8 4 6 5 NC TSSOP 8 1 6 3 NC Mini-MAP 4 5 2 7 NC Figure 1. SCL/CLK Serial Clock Input SDA/IO RST Serial Data Input/Output Reset Input Pin Configuration ISO Smart Card Module VCC=C1 RST=C2 SCL/CLK=C3 NC=C4 C5=GND C6=NC C7=SDA/IO C8=NC 8-lead SOIC, PDIP NC NC NC GND 1 2 3 4 8 7 6 5 VCC NC SCL SDA 8-lead TSSOP GND NC SDA NC 1 2 3 4 8 7 6 5 VCC NC C LK NC 8-lead Ultra Thin Mini-MAP (MLP 2x3) NC 8 SDA 7 NC 6 GND 5 1 2 3 4 NC CLK NC VCC Bottom View TWI Smart Card Module VCC=C1 NC=C2 SCL/CLK=C3 NC=C4 C5=GND C6=NC C7=SDA/IO C8=NC 1. Description The AT88SC0204CA member of the CryptoMemory® family is a high-performance secure memory providing 2 Kbit of user memory with advanced security and cryptographic features built in. The user memory is divided into four 64-byte zones, each of which may be individually set with different security access rights or effectively combined together to provide space for 1 to 4 data files. The AT88SC0204CA features an enhanced command set that allows direct communication with microcontroller hardware 2-Wire interface thereby allowing for faster firmware development with reduced code space requirements. 2 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 2. Smart Card Applications The AT88SC0204CA provides high security, low cost, and ease of implementation without the need for a microprocessor operating system. The embedded cryptographic engine provides for dynamic, symmetric-mutual authentication between the device and host, as well as performing stream encryption for all data and passwords exchanged between the device and host. Up to four unique key sets may be used for these operations. The AT88SC0204CA offers the ability to communicate with virtually any smart card reader using the asynchronous T = 0 protocol (Gemplus Patent) defined in ISO 7816-3. 3. Embedded Applications Through dynamic, symmetric-mutual authentication, data encryption, and the use of cryptographic Message Authentication Codes (MAC), the AT88SC0204CA provides a secure place for storage of sensitive information within a system. With its tamper detection circuits, this information remains safe even under attack. A 2-wire serial interface running at speeds up to 1.0 MHz provides fast and efficient communications with up to 15 individually addressable devices. The AT88SC0204CA is available in industry standard 8-lead packages with the same familiar pin configuration as AT24CXXX serial EEPROM devices. Note: Figure 2. Does not apply to either the TSSOP or the Ultra Thin Mini-Map pinouts. Block Diagram VCC GND Power Management Authentication, Encryption and Certification Unit Random Generator Synchronous Interface Data Transfer SCL/CLK SDA/IO RST Asynchronous ISO Interface Password Verification EEPROM Reset Block Answer to Reset 3 5202ES–CRYPT–08/09 4. Connection Diagram Figure 3. Connection Diagram 2.7v - 5.5v 2.7v - 3.6v Microprocessor CryptoMemory SDA SCL 5. 5.1. Pin Descriptions Supply Voltage (VCC) The VCC input is a 2.7V to 3.6V positive voltage supplied by the host. 5.2. Clock (SCL/CLK) When using the asynchronous T = 0 protocol, the CLK (SCL) input provides the device with a carrier frequency f. The nominal length of one bit emitted on I/O is defined as an “elementary time unit” (ETU) and is equal to 372/ f. When using the synchronous protocol, data clocking is done on the positive edge of the clock when writing to the device and on the negative edge of the clock when reading from the device. 5.3. Reset (RST) The AT88SC0204CA provides an ISO 7816-3 compliant asynchronous Answer-To-Reset (ATR) sequence. Upon activation of the reset sequence, the device outputs bytes contained in the 64-bit Answer-To-Reset register. An internal pull-up on the RST input pad allows the device to operate in synchronous mode without bonding RST. The AT88SC0204CA does not support an Answer-To-Reset sequence in the synchronous mode of operation. 5.4. Serial Data (SDA/IO) The SDA/IO pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wired with any number of other open-drain or open-collector devices. An external pull-up resistor should be connected between SDA/IO and VCC. The value of this resistor and the system capacitance loading the SDA/IO bus will determine the rise time of SDA/IO. This rise time will determine the maximum frequency during read operations. Low value pull-up resistors will allow higher frequency operations while drawing higher average power supply current. SDA/IO information applies to both asynchronous and synchronous protocols. 4 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 6. *Absolute Maximum Ratings Operating Temperature............................. −40°C to +85°C Storage Temperature ............................ −65°C to + 150°C Voltage on Any Pin with Respect to Ground ....................... − 0.7 to VCC +0.7V Maximum Operating Voltage.......................................4.0V DC Output Current ..................................................5.0 mA *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condition beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability. Table 2. DC Characteristics Applicable over recommended operating range from VCC = +2.7 to 3.6V, TAC = -40°C to +85°C (unless otherwise noted) Symbol VCC(1) ICC ICC ICC ICC ISB VIL VIL VIL VIH(1) VIH IIL IIL IIL IIH IIH IIH VOH VOL IOH IOL (1) (1) VIH Parameter Supply Voltage Supply Current Supply Current Supply Current Supply Current Standby Current SDA/IO Input Low Voltage CLK Input Low Voltage RST Input Low Voltage SDA/IO Input High Voltage SCL/CLK Input High Voltage RST Input High Voltage SDA/IO Input Low Current SCL/CLK Input Low Current RST Input Low Current SDA/IO Input High Current SCL/CLK Input High Current RST Input High Current SDA/IO Output High Voltage SDA/IO Output Low Voltage SDA/IO Output High Current SDA/IO Output Low Current Test Conditions Async READ at 3.57MHz Async WRITE at 3.57MHz Synch READ at 1MHz Synch WRITE at 1MHz VIN = VCC or GND Min 2.7 Typ Max 3.6 5 5 5 5 100 Units V mA mA mA mA μA V V V V V V μA μA μA μA μA μA V V μA mA 0 0 0 VCC x 0.7 VCC x 0.7 VCC x 0.7 0 < VIL < VCC x 0.15 0 < VIL < VCC x 0.15 0 < VIL < VCC x 0.15 VCC x 0.7 < VIH < VCC VCC x 0.7 < VIH < VCC VCC x 0.7 < VIH < VCC 20K ohm external pull-up IOL = 1mA VOH VOL VCC x 0.7 0 VCC x 0.2 VCC x 0.2 VCC x 0.2 5.5 5.5 5.5 15 15 50 20 100 150 VCC VCC x 0.15 20 10 5 5202ES–CRYPT–08/09 Note: 1. To prevent Latch Up Conditions from occurring during Power Up of the AT88SC0204CA, VCC must be turned on before applying VIH. For Powering Down, VIH must be removed before turning VCC off. AC Characteristics Table 3. Applicable over recommended operating range from VCC = +2.7 to 3.6V, TAC = -40°C to +85°C, CL = 30pF (unless otherwise noted) Symbol fCLK fCLK tR tF tR tF tAA tHD.STA tSU.STA tHD.DAT tSU.DAT tSU.STO tDH tWR Parameter Async Clock Frequency Synch Clock Frequency Clock Duty cycle “Rise Time - SDA/IO, RST” “Fall Time - SDA/IO, RST” Rise Time - SCL/CLK Fall Time - SCL/CLK Clock Low to Data Out Valid Start Hold Time Start Set-up Time Data In Hold Time Data In Set-up Time Stop Set-up Time Data Out Hold Time Write Cycle Time Min 1 0 40 Max 4 1 60 1 1 9% x period 9% x period 250 Units MHz MHz % μS μS μS μS nS nS nS nS nS nS nS 200 200 10 100 200 20 5 mS 6 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 7. 7.1. Device Operations for Synchronous Protocols Clock and Data Transitions The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 6 on page 8). Data changes during SCL high periods will indicate a start or stop condition as defined below. 7.1.1. Start condition A high-to-low transition of SDA with SCL high defines a START condition which must precede all commands (see Figure 7 on page 8). 7.1.2. Stop condition A low-to-high transition of SDA with SCL high defines a STOP condition. After a read sequence, the STOP condition will place the EEPROM in a standby power mode (see Figure 7 on page 8). 7.1.3. ACKNOWLEDGE All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle (see Figure 8 on page 9). 7.2. Memory Reset After an interruption in communication due protocol errors, power loss or any reason, perform "Acknowledge Polling" to properly recover from the condition. Acknowledge polling consists of sending a start condition followed by a valid CryptoMemory command byte and determining if the device responded with an ACKNOWLEDGE. Figure 4. Bus Time for 2-Wire Serial Communications. SCL: Serial Clock, SDA: Serial Data I/O tF tHIGH tLOW tR SCL tSU.STA tHD.STA tLOW tHD.DAT tSU.DAT tSU.STO SDA IN tAA tDH tBUF SDA OUT 7 5202ES–CRYPT–08/09 Figure 5. Write Cycle Timing. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn ACK twr STOP CONDITION (1) START CONDITION Note: The Write Cycle time twr is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. Data Validity Figure 6. SDA SCL DATA STABLE DATA CHANGE ALLOWED DATA STABLE Figure 7. START and STOP Definitions SDA SCL START STOP 8 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA Figure 8. Output Acknowledge SCL 1 8 9 DATA IN DATA OUT START ACKNOWLEDGE 9 5202ES–CRYPT–08/09 8. 8.1. Device Architecture User Zones The EEPROM user memory is divided into 4 zones of 512 bits each. Multiple zones allow for storage of different types of data or files in different zones. Access to user zones is permitted only after meeting proper security requirements. These security requirements are user definable in the configuration memory during device personalization. If the same security requirements are selected for multiple zones, then these zones may effectively be accessed as one larger zone. Figure 9. Zone $00 User 0 $38 $00 User 1 $38 $00 User 2 $38 $00 User 3 $38 64 Bytes 64 Bytes 64 Bytes 64 Bytes User Zones $0 $1 $2 $3 $4 $5 $6 $7 9. Control Logic Access to the user zones occur only through the control logic built into the device. This logic is configurable through access registers, key registers and keys programmed into the configuration memory during device personalization. Also implemented in the control logic is a cryptographic engine for performing the various higher-level security functions of the device. 10 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 10. Configuration Memory The configuration memory consists of 2048 bits of EEPROM memory used for storage of passwords, keys, codes, and also used for definition of security access rights for the user zones. Access rights to the configuration memory are defined in the control logic and are not alterable by the user after completion of personalization. Figure 10. $00 $08 $10 $18 $20 $28 $30 $38 $40 $48 $50 $58 $60 $68 $70 $78 $80 $88 $90 $98 $A0 $A8 $B0 $B8 $C0 $C8 $D0 $D8 $E0 $E8 $F0 $F8 Configuration Memory $0 $1 $3 $4 $5 $6 $7 Answer To Reset MTZ Card Manufacturer Code Lot History Code Identification Number Nc AR1 PR1 AR2 PR2 AR3 PR3 Reserved Issuer Code $2 Fab Code DCR AR0 Identifitcation Read Only PR0 Access Control For Authentication and Encryption use Cryptography For Authentication and Encryption use Secret PAC PAC PAC PAC PAC PAC PAC PAC Write 0 Write 1 Write 2 Write 3 Write 4 Write 5 Write 6 Write 7 PAC PAC PAC PAC PAC PAC PAC PAC Reserved Read 0 Read 1 Read 2 Read 3 Read 4 Read 5 Read 6 Read 7 Password Forbidden 10.1. Security Fuses There are three fuses on the device that must be blown during the device personalization process. Each fuse locks certain portions of the configuration zone as OTP (One-Time Programmable) memory. Fuses are designed for the module manufacturer, card manufacturer and card issuer and should be blown in sequence, although all programming of the device and blowing of the fuses may be performed at one final step. 11 5202ES–CRYPT–08/09 11. Communication Security Modes Communications between the device and host operate in three basic modes. Standard mode is the default mode for the device after power-up. Authentication mode is activated by a successful authentication sequence. Encryption mode is activated by a successful encryption activation following a successful authentication. Table 4. Standard Authentication Encryption Note: Communication Security Modes(1) Mode Configuration Data Clear Clear Clear User Data Clear Clear Encrypted Passwords Clear Encrypted Encrypted Data Integrity Check MDC(1) MAC(1) MAC(1) 1. Configuration data include viewable areas of the Configuration Zone except the passwords: MDC: Modification Detection Code. MAC: Message Authentication Code. 12. 12.1. Security Options Anti-Tearing In the event of a power loss during a write cycle, the integrity of the device’s stored data is recoverable. This function is optional: the host may choose to activate the anti-tearing function, depending on application requirements. When antitearing is active, write commands take longer to execute, since more write cycles are required to complete them, and data is limited to a maximum of eight bytes for each write request. Data is written first into a buffer zone in EEPROM instead of the intended destination address, but with the same access conditions. The data is then written in the required location. If this second write cycle is interrupted due to a power loss, the device will automatically recover the data from the system buffer zone at the next power-up. Nonvolatile buffering of the data is done automatically by the device. During power-up in applications using Anti-Tearing, the host is required to perform ACK polling in the event that the device needs to carry out the data recovery process. 12.2. Write Lock If a user zone is configured in the write lock mode, the lowest address byte of an 8-byte page constitutes a write access byte for the bytes of that page. For example, the write lock byte at $080 controls the bytes from $081 to $087. Figure 11. Address $080 Write Lock Example $0 11011001 $1 xxxx xxxx locked $2 xxxx xxxx locked $3 xxxx xxxx $4 xxxx xxxx $5 xxxx xxxx locked $6 xxxx xxxx $7 xxxx xxxx The Write-Lock byte itself may be locked by writing its least significant (rightmost) bit to “0”. Moreover, when write lock mode is activated, the write lock byte can only be programmed – that is, bits written to “0” cannot return to “1”. In the write lock configuration, write operations are limited to writing only one byte at a time. Attempts to write more than one byte will result in writing of just the first byte into the device. 12 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 12.3. Password Verification Passwords may be used to protect READ and/or WRITE access of any user zone. When a valid password is presented, it is memorized and active until power is turned off, unless a new password is presented or RST becomes active. There are eight password sets that may be used to protect any user zone. Only one password is active at a time. Presenting the correct WRITE password also grants READ access privileges. 12.4. Authentication Protocol The access to a user zone may be protected by an authentication protocol. Any one of four keys may be selected to use with a user zone. Authentication success is memorized and active as long as the chip is powered, unless a new authentication is initialized or RST becomes active. If the new authentication request is not validated, the card loses its previous authentication which must be presented again to gain access. Only the latest request is memorized. Figure 12. Password and Authentication Operations Device (Card) Card Number VERIFY A COMPUTE Challenge B Challenge B READ ACCESS VERIFY RPW DATA Checksum (CS) VERIFY WPW VERIFY CS Write DATA WRITE ACCESS AUTHENTICATION Host (Reader) COMPUTE Challenge A Challenge A VERIFY B Read Password (RPW) VERIFY CS Write Password (WPW) DATA CS Note: Authentication and password verification may be attempted at any time and in any order. Exceeding corresponding authentication or password attempts trial limit renders subsequent authentication or password verification attempts futile. 13 5202ES–CRYPT–08/09 12.5. Cryptographic Message Authentication Codes AT88SC0204CA implements a data validity check function in the standard, authentication or encryption modes of operation. In the standard mode, data validity check is done through a Modification Detection Code (MDC), in which the host may read an MDC from the device in order to verify that the data sent was received correctly. In authentication and encryption modes, the data validity check becomes more powerful since it provides a bidirectional data integrity check and data origin authentication capability in the form of a Message Authentication Codes (MAC). Only the host/device that carried out a valid authentication is capable of computing a valid MAC. While operating in the authentication or encryption modes, the use of MAC is required. For an ingoing command, if the device calculates a MAC different from the MAC transmitted by the host, not only is the command abandoned but the security privilege is revoked. A new authentication and/or encryption activation will be required to reactivate the MAC. 12.6. Encryption The data exchanged between the device and the host during read, write and verify password commands may be encrypted to ensure data confidentiality. The issuer may choose to require encryption for a user zone by settings made in the configuration memory. Any one of four keys may be selected for use with a user zone. In this case, activation of the encryption mode is required in order to read/write data in the zone and only encrypted data will be transmitted. Even if not required, the host may still elect to activate encryption provided the proper keys are known. 12.7. Supervisor Mode Enabling this feature allows the holder of one specific password to gain full access to all eight password sets, including the ability to change passwords. 12.8. Modify Forbidden No write access is allowed in a user zone protected with this feature at any time. The user zone must be written during device personalization prior to blowing the security fuses. 12.9. Program Only For a user zones protected by this feature, data can only be programmed (bits change from a “1” to a “0”), but not erased (bits change from a “0” to a “1”). 14 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 13. Protocol Selection The AT88SC0204CA supports two different communication protocols. Smartcard Applications: Smartcard applications use ISO 7816-B protocol in asynchronous T = 0 mode for compatibility and interoperability with industry standard smartcard readers. Embedded Applications: A 2-wire serial interface provides fast and efficient connectivity with other logic devices or microcontrollers. The power-up sequence determines establishes the communication protocol for use within that power cycle. Protocol selection is allowed only during power-up. 13.2. Synchronous 2-Wire Serial Interface The synchronous mode is the default mode after power up. This is due to the presence of an internal pull-up on RST. For embedded applications using CryptoMemory in standard plastic packages, this is the only available communication protocol. Power-up VCC, RST goes high also. After stable VCC, SCL(CLK) and SDA(I/O) may be driven. Once synchronous mode has been selected, it is not possible to switch to asynchronous mode without first powering off the device Figure 13. Synchronous 2-Wire Protocol Vcc I/O-SDA RST CLK-SCL Note: 1 2 3 4 5 Five clock pulses must be sent before the first command is issued. 15 5202ES–CRYPT–08/09 13.3. Asynchronous T = 0 Protocol This power-up sequence complies to ISO 7816-3 for a cold reset in smart card applications. VCC goes high; RST, I/O (SDA) and CLK (SCL) are low. Set I/O (SDA) in receive mode. Provide a clock signal to CLK (SCL). RST goes high after 400 clock cycles. The device will respond with a 64-bit ATR code, including historical bytes to indicate the memory density within the CryptoMemory family. Once asynchronous mode has been selected, it is not possible to switch to synchronous mode without first powering off the device. Figure 14. Asynchronous T = 0 Protocol (Gemplus Patent) Vcc I/O-SDA RST CLK-SCL ATR 14. Initial Device Programming Enabling the security features of CryptoMemory requires prior personalization. Personalization entails setting up of desired access rights by zones, passwords and key values, programming these values into the configuration memory with verification using simple WRITE and READ commands, and then blowing fuses to lock this information in place. Gaining access to the configuration memory requires successful presentation of a secure (or transport) code. The initial signature of the secure (transport) code for the AT88SC0204CA device is $E5 47 47. This is the same as the WRITE 7 password. The user may elect to change the signature of the secure code anytime after successful presentation. After writing and verifying data in the configuration memory, the security fuses MUST be blown to lock this information in the device. For additional information on personalizing CryptoMemory, please see the application notes Programming CryptoMemory for Embedded Applications and Initializing CryptoMemory for Smart Card Applications from the product page at www.atmel.com/products/securemem. 16 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 15. Ordering Information Table 5. Ordering Information Package M2 – J Module - ISO M2 – P Module - ISO M2 – J Module -TWI M2 – P Module -TWI 8P3 8S1 8A2 8Y6 7 mil wafer Ordering Code AT88SC0204CA-MJ AT88SC0204CA-MP AT88SC0204CA-MJTG AT88SC0204CA-MPTG AT88SC0204CA-PU AT88SC0204CA-SU AT88SC0204CA-TH AT88SC0204CA-Y6H-T AT88SC0204CA-WI Voltage Range 2.7V–3.6V Temperature Range Commercial (0°C to 70°C) 2.7V–3.6V Green compliant (exceeds RoHS)/Industrial (−40°C to 85°C) Industrial (−40°C to 85°C) 2.7V–3.6V Table 6. Ordering Information Description M2 ISO 7816 Smart Card Module with Atmel® Logo 8-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8-lead, 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8-lead, 2.0 x 3.0mm Body, 0.50mm Pitch, Ultra Thin Mini-Map, Dual No Lead Package (DFN), (MLP 2x3) 1. Formal drawings may be obtained from an Atmel sales office. 2. Both the J and P Module Packages are used for either ISO (T=0 / 2-wire mode) or TWI (2-wire mode only). Package Type(1) (2) M2 – P Module: ISO or TWI 8P3 8S1 8A2 8Y6 Note: M2 – J Module : ISO or TWI M2 ISO 7816 Smart Card Module 17 5202ES–CRYPT–08/09 16. Package Information Ordering Code: MJ or MJTG Module Size: M2 Dimension*: 12.6 x 11.4 [mm] Module Size: M2 Dimension*: 12.6 x 11.4 [mm] Glob Top: Square - 8.8 x 8.8 [mm] Thickness: 0.58 [mm] Pitch: 14.25 mm Ordering Code: MP or MPTG Glob Top: Round -  8.5 [mm] Thickness: 0.58 [mm] Pitch: 14.25 mm *Note: The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions of the module after excise or punching from the carrier tape are generally 0.4 mm greater in both directions (i.e., a punched M2 module will yield 13.0 x 11.8 mm). 18 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 17. 17.1. Ordering Code: SU 8-lead SOIC C 1 E E1 N L Top View End View e b A A1 SYMBOL A A1 b C D E1 E e L COMMON DIMENSIONS (Unit of Measure = mm) MIN 1.35 0.10 0.31 0.17 4.80 3.81 5.79 0.40 0˚ NOM – – – – – – – 1.27 BSC – – 1.27 8˚ MAX 1.75 0.25 0.51 0.25 5.05 3.99 6.20 NOTE D Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 3/17/05 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) DRAWING NO. 8S1 REV. C 19 5202ES–CRYPT–08/09 18. 18.1. Ordering Code: PU 8-lead PDIP 1 E E1 N Top View c eA End View COMMON DIMENSIONS (Unit of Measure = inches) D D1 e A2 A SYMBOL A A2 b b2 b3 c D D1 E E1 e eA L MIN − 0.115 0.014 0.045 0.030 0.008 0.355 0.005 0.300 0.240 NOM − 0.130 0.018 0.060 0.039 0.010 0.365 − 0.310 0.250 0.100 BSC 0.300 BSC MAX 0.210 0.195 0.022 0.070 0.045 0.014 0.400 − 0.325 0.280 NOTE 2 5 6 6 3 3 4 3 4 b2 b3 4 PLCS L b Side View 0.115 0.130 0.150 2 Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimensions A and L are measured with the pa ckage seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protusions. Mold Flash or protrusions shall not r exceed 0.010 inch. 4. E and eA measured with the leads const ained to be perpendicular to datum. r 5. Pointed or rounded lead tips are pre ferred to ease insertion. 6. b2 and b3 maximum dimensions do not include Dambar prot usions. Dambar protrusions shall not exceed r 0.010 (0.25 mm). 01/09/02 REV. B R 2325 Orchard Parkway San Jose, CA 95131 TITLE 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) DRAWING NO. 8P3 20 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA 19. 19.1. Ordering Code: TH 8-lead TSSOP 3 21 Pin 1 indicator this corner E1 E L1 N L Top View A End View SYMBOL COMMON DIMENSIONS (Unit of Measure = mm) MIN 2.90 4.30 – 0.80 0.19 0.45 NOM 3.00 6.40 BSC 4.40 – 1.00 – 0.65 BSC 0.60 1.00 RE3 0.75 4.50 1.20 1.05 0.30 4 3, 5 MAX 3.10 NOTE 2, 5 b D E E1 A A2 b e L L1 e D A2 Side View Notes: 1. This drawing is for general information only. Refer to JEDEC D rawing MO-153, Variation AA, for proper dimension s, tolerances, datums, etc. 2. Dimension D does not include mold Flash, prot rusions or gate burrs. Mold Flash, prot rusions and gate burrs shall not exceed 0.15 mm (0.006 in) per sid e. 3. Dimension E1 does not include inter-lead Flash or prot rusions. Inter-lead Flash and prot rusions shall not exceed 0.25 mm (0.010 in) per sid e. 4. Dimension b does not include Dambar prot rusion. Allowable Dambar prot rusion shall be 0.08 mm total in excess of the b dimension at maxi mum mate rial condition . Dambar cannot be located on the l ower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm . 5. Dimension D and E1 to be dete rmined at Datum Plane H . 10/29/08 REV. C TITLE Package Drawing Contact: packagedrawings@atmel.com 8A2, 8-lead, 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) GPC DRAWING NO. 8A2 TNR 21 5202ES–CRYPT–08/09 20. 20.1. Ordering Code: Y6H-T 8-lead Ultra Thin Mini-Map A D2 b (8X) Pin 1 Index Area E2 E Pin 1 ID L (8X) D A2 A3 A1 e (6X) 1.50 REF. COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL D E D2 E2 A A1 A2 A3 L e b 0.20 0.20 1.40 0.0 MIN NOM 2.00 BSC 3.00 BSC 1.50 0.02 0.20 REF 0.30 0.50 BSC 0.25 0.30 2 0.40 1.60 1.40 0.60 0.05 0.55 MAX NOTE Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 3. Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the device through this pad, so if soldered it should be tied to ground 11/21/08 TITLE GPC DRAWING NO. REV. 8Y6 E Package Drawing Contact: packagedrawings@atmel.com 8Y6, 8-lead, 2.0x3.0 mm Body, 0.50 mm Pitch, UltraThin Mini-MAP, Dual No Lead Package YNZ (Sawn)(UDFN) 22 AT88SC0204CA 5202ES–CRYPT–08/09 AT88SC0204CA Appendix A. Revision History Doc. Rev. 5202DS 5202DS 5202CS 5202BS 5202AS Date 08/2009 07/2009 05/2009 02/2009 07/2008 Minor edits and TWI module updates Minor updates to package drawing information and ordering information. Added Mini-MAP column to Table 1-1 and Mini-MAP pin-out drawing. Connection Diagram inserted; DC Characteristics table updated. Initial document release. Comments 23 5202ES–CRYPT–08/09 Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 International Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon Hong Kong Tel: (852) 2245-6100 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com/products/securemem Technical Support cryptomemory@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2009 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, CryptoMemory® and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 5202ES–CRYPT–08/09