AT89C51SND1C-ROTUL

Features • MPEG I/II-Layer 3 Hardwired Decoder – Stand-alone MP3 Decoder – 48, 44.1, 32, 24, 22.05, 16 kHz Sampling Frequency – Separated Digital Volume Control on Left and Right Channels (Software Control using 31 Steps) – Bass, Medium, and Treble Control (31 Steps) – Bass Boost Sound Effect – Ancillary Data Extraction – CRC Error and MPEG Frame Synchronization Indicators Programmable Audio Output for Interfacing with Common Audio DAC – PCM Format Compatible – I2S Format Compatible 8-bit MCU C51 Core Based (FMAX = 20 MHz) 2304 Bytes of Internal RAM 64K Bytes of Code Memory – AT89C51SND1C: Flash (100K Erase/Write Cycles) – AT83SND1C: ROM 4K Bytes of Boot Flash Memory (AT89C51SND1C) – ISP: Download from USB (standard) or UART (option) External Code Memory – AT80C51SND1C: ROMless USB Rev 1.1 Controller – Full Speed Data Transmission Built-in PLL – MP3 Audio Clocks – USB Clock MultiMedia Card® Interface Compatibility Atmel DataFlash® SPI Interface Compatibility IDE/ATAPI Interface 2 Channels 10-bit ADC, 8 kHz (8-true bit) – Battery Voltage Monitoring – Voice Recording Controlled by Software Up to 44 Bits of General-purpose I/Os – 4-bit Interrupt Keyboard Port for a 4 x n Matrix – SmartMedia® Software Interface 2 Standard 16-bit Timers/Counters Hardware Watchdog Timer Standard Full Duplex UART with Baud Rate Generator Two Wire Master and Slave Modes Controller SPI Master and Slave Modes Controller Power Management – Power-on Reset – Software Programmable MCU Clock – Idle Mode, Power-down Mode Operating Conditions: – 3V, ±10%, 25 mA Typical Operating at 25°C – Temperature Range: -40°C to +85°C Packages – TQFP80, BGA81, PLCC84 (Development Board) – Dice • • • • • • • • • • • • • • • • • • • Single-Chip Flash Microcontroller with MP3 Decoder and Human Interface AT83SND1C AT89C51SND1C AT80C51SND1C • • 4109JS–8051–10/06 1. Description The AT8xC51SND1C are fully integrated stand-alone hardwired MPEG I/II-Layer 3 decoder with a C51 microcontroller core handling data flow and MP3-player control. The AT89C51SND1C includes 64K Bytes of Flash memory and allows In-System Programming through an embedded 4K Bytes of Boot Flash memory. The AT83SND1C includes 64K Bytes of ROM memory. The AT80C51SND1C does not include any code memory. The AT8xC51SND1C include 2304 Bytes of RAM memory. The AT8xC51SND1C provides the necessary features for human interface like timers, keyboard port, serial or parallel interface (USB, TWI, SPI, IDE), ADC input, I2S output, and all external memory interface (NAND or NOR Flash, SmartMedia, MultiMedia, DataFlash cards). 2. Typical Applications • • • • MP3-Player PDA, Camera, Mobile Phone MP3 Car Audio/Multimedia MP3 Home Audio/Multimedia MP3 3. Block Diagram Figure 3-1. AT8xC51SND1C Block Diagram INT0 INT1 VDD VSS UVDD UVSS AVDD AVSS AREF AIN1:0 TXD RXD T0 T1 SS MISO MOSI SCK SCL SDA 3 3 Interrupt Handler Unit Flash ROM 64 KBytes Flash Boot 4 KBytes 3 3 3 3 4 4 4 4 1 1 RAM 2304 Bytes 10-bit A to D Converter UART and BRG Timers 0/1 Watchdog SPI/DataFlash Controller TWI Controller C51 (X2 Core) 8-Bit Internal Bus Clock and PLL Unit MP3 Decoder Unit I2S/PCM Audio Interface USB Controller MMC Interface Keyboard Interface I/O Ports IDE Interface 1 FILT X1 X2 RST ISP ALE DOUT DCLK DSEL SCLK D+ DMCLK MDAT MCMD KIN3:0 P0-P5 1 Alternate function of Port 1 3 Alternate function of Port 3 4 Alternate function of Port 4 2 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 4. Pin Description 4.1 Pinouts AT8xC51SND1C 80-pin QFP Package P5.1 P5.0 P0.0/AD0 P0.1/AD1 P0.2/AD2 P0.3/AD3 P0.4/AD4 P0.5/AD5 VSS VDD P0.6/AD6 P0.7/AD7 P4.3/SS P4.2/SCK P4.1/MOSI P4.0/MISO P2.0/A8 P2.1/A9 P4.7 P4.6 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 Figure 4-1. ALE ISP1/PSEN2/NC P1.0/KIN0 P1.1/KIN1 P1.2/KIN2 P1.3/KIN3 P1.4 P1.5 P1.6/SCL P1.7/SDA VDD PVDD FILT PVSS VSS X2 X1 TST UVDD UVSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 AT89C51SND1C-RO (FLASH) AT83SND1C-RO (ROM) AT80C51SND1C-RO (ROMLESS) 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 P4.5 P4.4 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14 P2.7/A15 VSS VDD MCLK MDAT MCMD RST SCLK DSEL DCLK DOUT VSS VDD Notes: 1. ISP pin is only available in AT89C51SND1C product. Do not connect this pin on AT83SND1C product. 2. PSEN pin is only available in AT80C51SND1C product. D+ DVDD VSS P3.0/RXD P3.1/TXD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P3.6/WR P3.7/RD AVDD AVSS AREFP AREFN AIN0 AIN1 P5.2 P5.3 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 3 4109JS–8051–10/06 Figure 4-2. AT8xC51SND1C 81-pin BGA Package 9 P4.6 8 P2.0/ A8 7 P4.0/ MISO P4.1/ MOSI P2.1/ A9 6 P4.2/ SCK P4.3/ SS 5 VDD 4 P0.2/ AD2 P0.4/ AD4 3 P0.3/ AD3 P0.0/ AD0 P1.0/ KIN0 P1.7/ SDA 2 P5.0 ISP1/ PSEN2 NC P1.3/ KIN3 1 ALE A B C D E F G H J P4.4 P4.7 P0.1/ AD1 P1.1 P2.5/ A13 P2.4/ A12 P2.2/ A10 P2.6/ A14 P2.3/ A11 P0.6 VSS P5.1 P1.2/ KIN2 P4.5 P0.7/ AD7 P2.7/ A15 P0.5/ AD5 P1.6/ SCL P1.5 P1.4 VDD VSS FILT PVDD X1 VDD RST MCMD MCLK MDAT AVDD P3.4/ T0 P3.5/ T1 P3.3/ INT1 P3.2/ INT0 UVSS PVSS X2 DSEL SCLK DOUT P5.3 P3.7/ RD VDD TST VSS DCLK VSS AIN1 AVSS AIN0 P3.1/ TXD P3.0/ RXD D- UVDD VDD P5.2 AREFP AREFN P3.6/ WR VSS D+ Notes: 1. ISP pin is only available in AT89C51SND1C product. Do not connect this pin on AT83SND1C and AT80C51SND1C product. 2. PSEN pin is only available in AT80C51SND1C product. 4 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C Figure 4-3. AT8xC51SND1C 84-pin PLCC Package NC P5.1 P5.0 P0.0/AD0 P0.1/AD1 P0.2/AD2 P0.3/AD3 P0.4/AD4 P0.5/AD5 VSS VDD P0.6/AD6 P0.7/AD7 P4.3/SS P4.2/SCK P4.1/MOSI P4.0/MISO P2.0/A8 P2.1/A9 P4.7 P4.6 ALE ISP P1.0/KIN0 P1.1/KIN1 P1.2/KIN2 P1.3/KIN3 P1.4 P1.5 P1.6/SCL P1.7/SDA VDD PAVDD FILT PAVSS VSS X2 NC X1 TST UVDD UVSS 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 11 10 9 8 7 6 5 4 3 2 1 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 AT89C51SND1C-SR (FLASH) NC P4.5 P4.4 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14 P2.7/A15 VSS VDD MCLK MDAT MCMD RST SCLK DSEL DCLK DOUT VSS VDD 4.2 Signals All the AT8xC51SND1C signals are detailed by functionality in Table 1 to Table 14. Table 1. Ports Signal Description Signal Name Type Description Port 0 P0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1s written to them float and can be used as high impedance inputs. To avoid any parasitic current consumption, floating P0 inputs must be polarized to VDD or VSS. Port 1 P1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 P2 is an 8-bit bidirectional I/O port with internal pull-ups. Alternate Function P0.7:0 I/O D+ DVDD VSS P3.0/RXD P3.1/TXD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P3.6/WR P3.7/RD AVDD AVSS AREFP AREFN AIN0 AIN1 P5.2 P5.3 NC 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 AD7:0 P1.7:0 I/O KIN3:0 SCL SDA A15:8 P2.7:0 I/O 5 4109JS–8051–10/06 Signal Name Type Description Alternate Function RXD TXD P3.7:0 I/O Port 3 P3 is an 8-bit bidirectional I/O port with internal pull-ups. INT0 INT1 T0 T1 WR RD MISO MOSI SCK SS - P4.7:0 I/O Port 4 P4 is an 8-bit bidirectional I/O port with internal pull-ups. P5.3:0 I/O Port 5 P5 is a 4-bit bidirectional I/O port with internal pull-ups. Table 2. Clock Signal Description Signal Name Type Description Input to the on-chip inverting oscillator amplifier To use the internal oscillator, a crystal/resonator circuit is connected to this pin. If an external oscillator is used, its output is connected to this pin. X1 is the clock source for internal timing. Output of the on-chip inverting oscillator amplifier To use the internal oscillator, a crystal/resonator circuit is connected to this pin. If an external oscillator is used, leave X2 unconnected. PLL Low Pass Filter input FILT receives the RC network of the PLL low pass filter. Alternate Function X1 I - X2 O - FILT I - Table 3. Timer 0 and Timer 1 Signal Description Signal Name Type Description Timer 0 Gate Input INT0 serves as external run control for timer 0, when selected by GATE0 bit in TCON register. INT0 I External Interrupt 0 INT0 input sets IE0 in the TCON register. If bit IT0 in this register is set, bit IE0 is set by a falling edge on INT0. If bit IT0 is cleared, bit IE0 is set by a low level on INT0. Timer 1 Gate Input INT1 serves as external run control for timer 1, when selected by GATE1 bit in TCON register. INT1 I External Interrupt 1 INT1 input sets IE1 in the TCON register. If bit IT1 in this register is set, bit IE1 is set by a falling edge on INT1. If bit IT1 is cleared, bit IE1 is set by a low level on INT1. P3.3 P3.2 Alternate Function 6 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C Signal Name Type Description Timer 0 External Clock Input When timer 0 operates as a counter, a falling edge on the T0 pin increments the count. Timer 1 External Clock Input When timer 1 operates as a counter, a falling edge on the T1 pin increments the count. Alternate Function T0 I P3.4 T1 I P3.5 Table 4. Audio Interface Signal Description Signal Name DCLK DOUT DSEL Type O O O Description DAC Data Bit Clock DAC Audio Data DAC Channel Select Signal DSEL is the sample rate clock output. DAC System Clock SCLK is the oversampling clock synchronized to the digital audio data (DOUT) and the channel selection signal (DSEL). Alternate Function - SCLK O - Table 5. USB Controller Signal Description Signal Name Type Description USB Positive Data Upstream Port This pin requires an external 1.5 KΩ pull-up to VDD for full speed operation. USB Negative Data Upstream Port Alternate Function D+ I/O - D- I/O - Table 6. MutiMediaCard Interface Signal Description Signal Name MCLK Type O Description MMC Clock output Data or command clock transfer. MMC Command line Bidirectional command channel used for card initialization and data transfer commands. To avoid any parasitic current consumption, unused MCMD input must be polarized to VDD or VSS. MMC Data line Bidirectional data channel. To avoid any parasitic current consumption, unused MDAT input must be polarized to VDD or VSS. Alternate Function - MCMD I/O - MDAT I/O - 7 4109JS–8051–10/06 Table 7. UART Signal Description Signal Name Type Description Receive Serial Data RXD sends and receives data in serial I/O mode 0 and receives data in serial I/O modes 1, 2 and 3. Transmit Serial Data TXD outputs the shift clock in serial I/O mode 0 and transmits data in serial I/O modes 1, 2 and 3. Alternate Function RXD I/O P3.0 TXD O P3.1 Table 8. SPI Controller Signal Description Signal Name Type Description SPI Master Input Slave Output Data Line When in master mode, MISO receives data from the slave peripheral. When in slave mode, MISO outputs data to the master controller. SPI Master Output Slave Input Data Line When in master mode, MOSI outputs data to the slave peripheral. When in slave mode, MOSI receives data from the master controller. SPI Clock Line When in master mode, SCK outputs clock to the slave peripheral. When in slave mode, SCK receives clock from the master controller. SPI Slave Select Line When in controlled slave mode, SS enables the slave mode. Alternate Function MISO I/O P4.0 MOSI I/O P4.1 SCK I/O P4.2 SS I P4.3 Table 9. TWI Controller Signal Description Signal Name Type Description TWI Serial Clock When TWI controller is in master mode, SCL outputs the serial clock to the slave peripherals. When TWI controller is in slave mode, SCL receives clock from the master controller. TWI Serial Data SDA is the bidirectional Two Wire data line. Alternate Function SCL I/O P1.6 SDA I/O P1.7 Table 10. A/D Converter Signal Description Signal Name AIN1:0 AREFP AREFN Type I I I Description A/D Converter Analog Inputs Analog Positive Voltage Reference Input Analog Negative Voltage Reference Input This pin is internally connected to AVSS. Alternate Function - 8 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C Table 11. Keypad Interface Signal Description Signal Name Type Description Keypad Input Lines Holding one of these pins high or low for 24 oscillator periods triggers a keypad interrupt. Alternate Function KIN3:0 I P1.3:0 Table 12. External Access Signal Description Signal Name Type Description Address Lines Upper address lines for the external bus. Multiplexed higher address and data lines for the IDE interface. Address/Data Lines Multiplexed lower address and data lines for the external memory or the IDE interface. Address Latch Enable Output ALE signals the start of an external bus cycle and indicates that valid address information is available on lines A7:0. An external latch is used to demultiplex the address from address/data bus. Program Store Enable Output (AT80C51SND1C Only) This signal is active low during external code fetch or external code read (MOVC instruction). ISP Enable Input (AT89C51SND1C Only) This signal must be held to GND through a pull-down resistor at the falling reset to force execution of the internal bootloader. Read Signal Read signal asserted during external data memory read operation. Write Signal Write signal asserted during external data memory write operation. External Access Enable (Dice Only) EA must be externally held low to enable the device to fetch code from external program memory locations 0000h to FFFFh. Alternate Function A15:8 I/O P2.7:0 AD7:0 I/O P0.7:0 ALE O - PSEN I/O - ISP I/O - RD O P3.7 WR O P3.6 EA(1)(2) I - Notes: 1. For ROM/Flash Dice product versions: pad EA must be connected to VCC. 2. For ROMless Dice product versions: pad EA must be connected to VSS. Table 13. System Signal Description Signal Name Type Description Reset Input Holding this pin high for 64 oscillator periods while the oscillator is running resets the device. The Port pins are driven to their reset conditions when a voltage lower than VIL is applied, whether or not the oscillator is running. This pin has an internal pull-down resistor which allows the device to be reset by connecting a capacitor between this pin and VDD. Asserting RST when the chip is in Idle mode or Power-Down mode returns the chip to normal operation. Test Input Test mode entry signal. This pin must be set to VDD. Alternate Function RST I - TST I - 9 4109JS–8051–10/06 Table 14. Power Signal Description Signal Name VDD Type PWR Description Digital Supply Voltage Connect these pins to +3V supply voltage. Circuit Ground Connect these pins to ground. Analog Supply Voltage Connect this pin to +3V supply voltage. Analog Ground Connect this pin to ground. PLL Supply voltage Connect this pin to +3V supply voltage. PLL Circuit Ground Connect this pin to ground. USB Supply Voltage Connect this pin to +3V supply voltage. USB Ground Connect this pin to ground. Alternate Function - VSS GND - AVDD PWR - AVSS GND - PVDD PWR - PVSS GND - UVDD PWR - UVSS GND - 10 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 4.3 Internal Pin Structure Table 15. Detailed Internal Pin Structure Circuit(1) VDD Type Pins RTST Input TST VDD Watchdog Output P Input/Output RRST RST VSS 2 osc periods Latch Output VDD VDD VDD P1 P2 P3 Input/Output N VSS VDD P1(2) P2(3) P3 P4 P53:0 P Input/Output N VSS VDD P0 MCMD MDAT ISP PSEN P Output N VSS ALE SCLK DCLK DOUT DSEL MCLK D+ D- Input/Output D+ D- Notes: 1. For information on resistors value, input/output levels, and drive capability, refer to the Section “DC Characteristics”, page 180. 2. When the Two Wire controller is enabled, P1, P2, and P3 transistors are disabled allowing pseudo open-drain structure. 3. In Port 2, P1 transistor is continuously driven when outputting a high level bit address (A15:8). 11 4109JS–8051–10/06 5. Application Information Figure 5-1. AT8xC51SND1C Typical Application with On-Board Atmel DataFlash and 2-wire LCD LCD Battery Ref. P1.6/SCL P1.7/SDA VREFP P1.0/KIN0 P1.1/KIN1 P1.2/KIN2 P1.3/KIN3 P0.0 P0.1 P0.2 P0.3 X1 X2 VREFN AVDD AIN1 AIN0 VDD RST MMC1 MCLK MDAT MCMD MMC2 AT8xC51SND1C UVDD D+ DUVSS USB PORT P4.2/SCK P4.0/SI DOUT DCLK DSEL SCLK FILT PVSS P4n P4.1/SO DataFlash Memories Audio DAC 12 AT8xC51SND1C 4109JS–8051–10/06 AVSS P1.4 P1.5 VSS AT8xC51SND1C Figure 5-2. AT8xC51SND1C Typical Application with On-Board Atmel DataFlash and // LCD LCD Battery P1.6/SCL P1.7/SDA Ref. P1.3 P0.4 P0.5 P0.6 P0.7 VREFP VREFN AVDD AIN1 AIN0 VDD RST P1.0/KIN0 P1.1/KIN1 P1.2/KIN2 P0.0 P0.1 P0.2 P0.3 X1 X2 MMC1 MCLK MDAT MCMD MMC2 AT8xC51SND1C UVDD D+ DUVSS USB PORT P4.2/SCK P4.0/SI DOUT DCLK DSEL SCLK FILT P4.n PVSS P4.1/SO DataFlash Memories Audio DAC Figure 5-3. AT8xC51SND1C Typical Application with On-Board SSFDC Flash LCD Battery Ref. P4.0 P4.1 P4.2 P4.4 P4.5 P4.6 P4.7 VREFN P1.0/KIN0 P1.1/KIN1 P1.2/KIN2 P1.3/KIN3 P0.0 P0.1 P0.2 P0.3 X1 X2 VREFP AVDD AIN1 AIN0 VDD RST AVSS P1.4 P1.5 VSS MMC1 MCLK MDAT MCMD MMC2 AT8xC51SND1C UVDD D+ DUVSS USB PORT P3.6/WR# DOUT DCLK DSEL SCLK FILT P2 PVSS P0 P3.7/RD# Audio DAC SSFDC Memories or SmartMedia Cards SmartMedia AVSS P3.4 P3.5 VSS 13 4109JS–8051–10/06 Figure 5-4. AT8xC51SND1C Typical Application with IDE CD-ROM Drive LCD Battery P1.6/SCL P1.7/SDA Ref. P4.0 P4.1 P4.2 P4.4 P4.5 P4.6 P4.7 VREFN VDD VREFP AVDD AIN1 AIN0 RST P1.0/KIN0 P1.1/KIN1 P1.2/KIN2 P0.0 P0.1 P0.2 P0.3 X1 X2 P3.6/WR# FILT P2 PVSS P0 MMC1 MCLK MDAT MCMD MMC2 AT8xC51SND1C UVDD D+ DUVSS USB PORT P3.7/RD# DOUT DCLK DSEL SCLK Audio DAC IDE CD-ROM 14 AT8xC51SND1C 4109JS–8051–10/06 AVSS P3.4 P3.5 VSS AT8xC51SND1C 1. Peripherals The AT8xC51SND1C peripherals are briefly described in the following sections. For further details on how to interface (hardware and software) to these peripherals, please refer to the AT8xC51SND1C design guide. 1.1 Clock Generator System The AT8xC51SND1C internal clocks are extracted from an on-chip PLL fed by an onchip oscillator. Four clocks are generated respectively for the C51 core, the MP3 decoder, the audio interface, and the other peripherals. The C51 and peripheral clocks are derived from the oscillator clock. The MP3 decoder clock is generated by dividing the PLL output clock. The audio interface sample rates are also obtained by dividing the PLL output clock. 1.2 Ports The AT8xC51SND1C implements five 8-bit ports (P0 to P4) and one 4-bit port (P5). In addition to performing general-purpose I/O, some ports are capable of external data memory operations; others allow for alternate functions. All I/O Ports are bidirectional. Each Port contains a latch, an output driver and an input buffer. Port 0 and Port 2 output drivers and input buffers facilitate external memory operations. Some Port 1, Port 3 and Port 4 pins serve for both general-purpose I/O and alternate functions. 1.3 Timers/Counters The AT8xC51SND1C implements the two general-purpose, 16-bit Timers/Counters of a standard C51. They are identified as Timer 0, Timer 1, and can independently be configured each to operate in a variety of modes as a Timer or as an event Counter. When operating as a Timer, a Timer/Counter runs for a programmed length of time, then issues an interrupt request. When operating as a Counter, a Timer/Counter counts negative transitions on an external pin. After a preset number of counts, the Counter issues an interrupt request. 1.4 Watchdog Timer The AT8xC51SND1C implements a hardware Watchdog Timer that automatically resets the chip if it is allowed to time out. The WDT provides a means of recovering from routines that do not complete successfully due to software or hardware malfunctions. 1.5 MP3 Decoder The AT8xC51SND1C implements a MPEG I/II audio layer 3 decoder (known as MP3 decoder). In MPEG I (ISO 11172-3) three layers of compression have been standardized supporting three sampling frequencies: 48, 44.1, and 32 KHz. Among these layers, layer 3 allows highest compression rate of about 12:1 while still maintaining CD audio quality. For example, 3 minutes of CD audio (16-bit PCM, 44.1 KHz) data, which needs about 32 MBytes of storage, can be encoded into only 2.7 MBytes of MPEG I audio layer 3 data. In MPEG II (ISO 13818-3), three additional sampling frequencies: 24, 22.05, and 16 KHz are supported for low bit rates applications. The AT8xC51SND1C can decode in real-time the MPEG I audio layer 3 encoded data into a PCM audio data, and also supports MPEG II audio layer 3 additional frequencies. 15 4109JS–8051–10/06 Additional features are supported by the AT8xC51SND1C MP3 decoder such as volume, bass, medium, and treble controls, bass boost effect and ancillary data extraction. 1.6 Audio Output Interface The AT8xC51SND1C implements an audio output interface allowing the decoded audio bitstream to be output in various formats. It is compatible with right and left justification PCM and I2S formats and thanks to the on-chip PLL (see Section 1.1) allows connection of almost all of the commercial audio DAC families available on the market. 1.7 Universal Serial Bus Interface The AT8xC51SND1C implements a full speed Universal Serial Bus Interface. It can be used for the following purposes: • • Download of MP3 encoded audio files by supporting the USB mass storage class. In System Programming by supporting the USB firmware upgrade class. 1.8 MultiMediaCard Interface The AT8xC51SND1C implements a MultiMediaCard (MMC) interface compliant to the V2.2 specification in MultiMediaCard Mode. The MMC allows storage of MP3 encoded audio files in removable flash memory cards that can be easily plugged or removed from the application. It can also be used for In System Programming. 1.9 IDE/ATAPI interface The AT8xC51SND1C provides an IDE/ATAPI interface allowing connexion of devices such as CD-ROM reader, CompactFlash cards, Hard Disk Drive… It consists in a 16-bit bidirectional bus part of the low-level ANSI ATA/ATAPI specification. It is provided for mass storage interface but could be used for In System Programming using CD-ROM. 1.10 Serial I/O Interface The AT8xC51SND1C implements a serial port with its own baud rate generator providing one single synchronous communication mode and three full-duplex Universal Asynchronous Receiver Transmitter (UART) communication modes. It is provided for the following purposes: • • In System Programming. Remote control of the AT8xC51SND1C by a host. 1.11 Serial Peripheral Interface The AT8xC51SND1C implements a Serial Peripheral Interface (SPI) supporting master and slave modes. It is provided for the following purposes: • • • Interfacing DataFlash memory for MP3 encoded audio files storage. Remote control of the AT8xC51SND1C by a host. In System Programming. 16 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 1.12 2-wire Controller The AT8xC51SND1C implements a 2-wire controller supporting the four standard master and slave modes with multimaster capability. It is provided for the following purposes: • • • Connection of slave devices like LCD controller, audio DAC… Remote control of the AT8xC51SND1C by a host. In System Programming. 1.13 A/D Controller The AT8xC51SND1C implements a 2-channel 10-bit (8 true bits) analog to digital converter (ADC). It is provided for the following purposes: • • • Battery monitoring. Voice recording. Corded remote control. 1.14 Keyboard Interface The AT8xC51SND1C implements a keyboard interface allowing connection of 4 x n matrix keyboard. It is based on 4 inputs with programmable interrupt capability on both high or low level. These inputs are available as alternate function of P1.3:0 and allow exit from idle and power down modes. 17 4109JS–8051–10/06 22. Electrical Characteristics 22.1 Absolute Maximum Rating *NOTICE: .................................... -0.3 Storage Temperature ......................................... -65 to +150°C Voltage on any other Pin to VSS to +4.0 V IOL per I/O Pin ................................................................. 5 mA Power Dissipation ............................................................. 1 W Operating Conditions Ambient Temperature Under Bias........................ -40 to +85°C VDD ........................................................................................................................ 4.0V Stressing the device beyond the “Absolute Maximum Ratings” may cause permanent damage. These are stress ratings only. Operation beyond the “operating conditions” is not recommended and extended exposure beyond the “Operating Conditions” may affect device reliability. 22.2 22.2.1 DC Characteristics Digital Logic Table 143. Digital DC Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol VIL VIH1 (2) Parameter Input Low Voltage Input High Voltage (except RST, X1) Input High Voltage (RST, X1) Output Low Voltage (except P0, ALE, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT) Output Low Voltage (P0, ALE, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT) Output High Voltage (P1, P2, P3, P4 and P5) Output High Voltage (P0, P2 address mode, ALE, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT, D+, D-) Logical 0 Input Current (P1, P2, P3, P4 and P5) Input Leakage Current (P0, ALE, MCMD, MDAT, MCLK, SCLK, DCLK, DSEL, DOUT) Logical 1 to 0 Transition Current (P1, P2, P3, P4 and P5) Pull-Down Resistor Pin Capacitance VDD Data Retention Limit Min -0.5 0.2·VDD + 1.1 0.7·VDD Typ(1) Max 0.2·VDD - 0.1 VDD VDD + 0.5 0.45 Units V V V Test Conditions VIH2 VOL1 V IOL= 1.6 mA VOL2 0.45 V IOL= 3.2 mA VOH1 VDD - 0.7 V IOH= -30 μA VOH2 VDD - 0.7 V IOH= -3.2 mA IIL -50 μA VIN= 0.45 V ILI 10 μA 0.45< VIN< VDD ITL RRST CIO VRET -650 50 90 10 1.8 200 μA kΩ pF V VIN= 2.0 V TA= 25°C 180 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C Table 143. Digital DC Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol Parameter Min Typ(1) Max X1 / X2 mode 6.5 / 10.5 8 / 13.5 9.5 / 17 X1 / X2 mode 6.5 / 10.5 8 / 13.5 9.5 / 17 X1 / X2 mode 6.5 / 10.5 8 / 13.5 9.5 / 17 X1 / X2 mode 5.3 / 8.1 6.4 / 10.3 7.5 / 13 X1 / X2 mode 5.3 / 8.1 6.4 / 10.3 7.5 / 13 X1 / X2 mode 5.3 / 8.1 6.4 / 10.3 7.5 / 13 20 500 Units Test Conditions VDD < 3.3 V mA 12 MHz 16 MHz 20 MHz VDD < 3.3 V mA 12 MHz 16 MHz 20 MHz VDD < 3.3 V mA 12 MHz 16 MHz 20 MHz VDD < 3.3 V mA 12 MHz 16 MHz 20 MHz VDD < 3.3 V mA 12 MHz 16 MHz 20 MHz VDD < 3.3 V mA 12 MHz 16 MHz 20 MHz VRET < VDD < 3.3 V VRET < VDD < 3.3 V VRET < VDD < 3.3 V VDD < 3.3 V AT89C51SND1C Operating Current (3) IDD AT83SND1C Operating Current AT80C51SND1C Idle Mode Current AT89C51SND1C Idle Mode Current (3) IDL AT83SND1C Idle Mode Current AT80C51SND1C Idle Mode Current AT89C51SND1C Power-Down Mode Current IPD AT83SND1C Power-Down Mode Current AT80C51SND1C Power-Down Mode Current IFP AT89C51SND1C Flash Programming Current μA μA μA mA 20 500 20 500 15 Notes: 1. Typical values are obtained using VDD= 3 V and TA= 25°C. They are not tested and there is no guarantee on these values. 2. Flash retention is guaranteed with the same formula for VDD min down to 0V. 3. See Table 144 for typical consumption in player mode. Table 144. Typical Reference Design AT89C51SND1C Power Consumption Player Mode Stop IDD 10 mA Test Conditions AT89C51SND1C at 16 MHz, X2 mode, VDD= 3 V No song playing AT89C51SND1C at 16 MHz, X2 mode, VDD= 3 V MP3 Song with Fs= 44.1 KHz, at any bit rates (Variable Bit Rate) Playing 30 mA 181 4109JS–8051–10/06 22.2.1.1 IDD, IDL and IPD Test Conditions Figure 22-1. IDD Test Condition, Active Mode VDD VDD RST VDD PVDD UVDD AVDD IDD (NC) Clock Signal X2 X1 P0 VSS PVSS UVSS AVSS TST VDD VSS All other pins are unconnected Figure 22-2. IDL Test Condition, Idle Mode VDD RST VSS VDD PVDD UVDD AVDD IDL (NC) Clock Signal X2 X1 P0 VSS PVSS UVSS AVSS TST VDD VSS All other pins are unconnected Figure 22-3. IPD Test Condition, Power-Down Mode VDD RST VSS VDD PVDD UVDD AVDD P0 MCMD MDAT TST IPD VDD (NC) X2 X1 VSS PVSS UVSS AVSS VSS All other pins are unconnected 182 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.2.2 A to D Converter Table 145. A to D Converter DC Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol AVDD AIDD Parameter Analog Supply Voltage Min 2.7 Typ Max 3.3 Units V μA AVDD= 3.3V AIN1:0= 0 to AVDD ADEN= 1 AVDD= 3.3V ADEN= 0 or PD= 1 Test Conditions Analog Operating Supply Current 600 AIPD AVIN AVREF RREF CIA Analog Standby Current Analog Input Voltage Reference Voltage AREFN AREFP AREF Input Resistance Analog Input capacitance AVSS AVSS 2.4 10 2 AVDD μA V V AVDD 30 10 KΩ pF TA= 25°C TA= 25°C 22.2.3 22.2.3.1 Oscillator & Crystal Schematic Figure 22-4. Crystal Connection X1 C1 Q C2 VSS X2 Note: For operation with most standard crystals, no external components are needed on X1 and X2. It may be necessary to add external capacitors on X1 and X2 to ground in special cases (max 10 pF). X1 and X2 may not be used to drive other circuits. 22.2.3.2 Parameters Table 146. Oscillator & Crystal Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol CX1 CX2 CL DL F RS CS Parameter Internal Capacitance (X1 - VSS) Internal Capacitance (X2 - VSS) Equivalent Load Capacitance (X1 - X2) Drive Level Crystal Frequency Crystal Series Resistance Crystal Shunt Capacitance Min Typ 10 10 5 50 20 40 6 Max Unit pF pF pF μW MHz Ω pF 183 4109JS–8051–10/06 22.2.4 22.2.4.1 Phase Lock Loop Schematic Figure 22-5. PLL Filter Connection FILT R C1 VSS VSS C2 22.2.4.2 Parameters Table 147. PLL Filter Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol R C1 C2 Filter Resistor Filter Capacitance 1 Filter Capacitance 2 Parameter Min Typ 100 10 2.2 Max Unit Ω nF nF 22.2.5 22.2.5.1 USB Connection Schematic Figure 22-6. USB Connection VDD VBUS D+ DGND To Power Supply RFS RUSB RUSB D+ D- VSS 22.2.5.2 Parameters Table 148. USB Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol RUSB RFS Parameter USB Termination Resistor USB Full Speed Resistor Min Typ 27 1.5 Max Unit Ω KΩ 184 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.2.6 22.2.6.1 In System Programming Schematic Figure 22-7. ISP Pull-Down Connection ISP RISP VSS 22.2.6.2 Parameters Table 149. ISP Pull-Down Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol RISP Parameter ISP Pull-Down Resistor Min Typ 2.2 Max Unit KΩ 185 4109JS–8051–10/06 22.3 22.3.1 AC Characteristics External Program Bus Cycles Definition of Symbols Table 150. External Program Bus Cycles Timing Symbol Definitions Signals A I L P Address Instruction In ALE PSEN H L V X Z Conditions High Low Valid No Longer Valid Floating 22.3.1.1 22.3.1.2 Timings Test conditions: capacitive load on all pins= 50 pF. Table 151. External Program Bus Cycle - Read AC Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C Variable Clock Standard Mode Symbol TCLCL TLHLL TAVLL TLLAX TLLIV TPLPH TPLIV TPXIX TPXIZ TAVIV TPLAZ Parameter Clock Period ALE Pulse Width Address Valid to ALE Low Address hold after ALE Low ALE Low to Valid Instruction PSEN Pulse Width PSEN Low to Valid Instruction Instruction Hold After PSEN High Instruction Float After PSEN High Address Valid to Valid Instruction PSEN Low to Address Float 0 TCLCL-10 5·TCLCL-35 10 Min 50 2·TCLCL-15 TCLCL-20 TCLCL-20 4·TCLCL-35 3·TCLCL-25 3·TCLCL-35 0 0.5·TCLCL-10 2.5·TCLCL-35 10 Max Variable Clock X2 Mode Min 50 TCLCL-15 0.5·TCLCL-20 0.5·TCLCL-20 2·TCLCL-35 1.5·TCLCL-25 1.5·TCLCL-35 Max Unit ns ns ns ns ns ns ns ns ns ns ns 186 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.3.1.3 Waveforms Figure 22-8. External Program Bus Cycle - Read Waveforms ALE TLHLL TLLPL PSEN TPLIV TPLAZ TAVLL TLLAX P0 D7:0 A7:0 TPXAV TPXIZ TPXIX D7:0 Instruction In P2 A15:8 A7:0 D7:0 Instruction In A15:8 TPLPH 22.3.2 22.3.2.1 External Data 8-bit Bus Cycles Definition of Symbols Table 152. External Data 8-bit Bus Cycles Timing Symbol Definitions Signals A D L Q R W Address Data In ALE Data Out RD WR H L V X Z Conditions High Low Valid No Longer Valid Floating 22.3.2.2 Timings Test conditions: capacitive load on all pins= 50 pF. Table 153. External Data 8-bit Bus Cycle - Read AC Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C Variable Clock Standard Mode Symbol TCLCL TLHLL TAVLL TLLAX TLLRL Parameter Clock Period ALE Pulse Width Address Valid to ALE Low Address hold after ALE Low ALE Low to RD Low Min 50 2·TCLCL-15 TCLCL-20 TCLCL-20 3·TCLCL-30 Max Variable Clock X2 Mode Min 50 TCLCL-15 0.5·TCLCL-20 0.5·TCLCL-20 1.5·TCLCL-30 Max Unit ns ns ns ns ns 187 4109JS–8051–10/06 Variable Clock Standard Mode Symbol TRLRH TRHLH TAVDV TAVRL TRLDV TRLAZ TRHDX TRHDZ Parameter RD Pulse Width RD high to ALE High Address Valid to Valid Data In Address Valid to RD Low RD Low to Valid Data RD Low to Address Float Data Hold After RD High Data Float After RD High 0 2·TCLCL-25 4·TCLCL-30 5·TCLCL-30 0 Min 6·TCLCL-25 TCLCL-20 TCLCL+20 9·TCLCL-65 Max Variable Clock X2 Mode Min 3·TCLCL-25 0.5·TCLCL-20 0.5·TCLCL+20 4.5·TCLCL-65 2·TCLCL-30 2.5·TCLCL-30 0 0 TCLCL-25 Max Unit ns ns ns ns ns ns ns ns Table 154. External Data 8-bit Bus Cycle - Write AC Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C Variable Clock Standard Mode Symbol TCLCL TLHLL TAVLL TLLAX TLLWL TWLWH TWHLH TAVWL TQVWH TWHQX Parameter Clock Period ALE Pulse Width Address Valid to ALE Low Address hold after ALE Low ALE Low to WR Low WR Pulse Width WR High to ALE High Address Valid to WR Low Data Valid to WR High Data Hold after WR High Min 50 2·TCLCL-15 TCLCL-20 TCLCL-20 3·TCLCL-30 6·TCLCL-25 TCLCL-20 4·TCLCL-30 7·TCLCL-20 TCLCL-15 TCLCL+20 Max Variable Clock X2 Mode Min 50 TCLCL-15 0.5·TCLCL-20 0.5·TCLCL-20 1.5·TCLCL-30 3·TCLCL-25 0.5·TCLCL-20 2·TCLCL-30 3.5·TCLCL-20 0.5·TCLCL-15 0.5·TCLCL+20 Max Unit ns ns ns ns ns ns ns ns ns ns 188 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.3.2.3 Waveforms Figure 22-9. External Data 8-bit Bus Cycle - Read Waveforms ALE TLHLL TLLRL TRLRH TRHLH RD TRLDV TRLAZ TAVLL P0 TLLAX A7:0 TAVRL TAVDV P2 A15:8 D7:0 Data In TRHDZ TRHDX Figure 22-10. External Data 8-bit Bus Cycle - Write Waveforms ALE TLHLL TLLWL TWLWH TWHLH WR TAVWL TAVLL P0 TLLAX A7:0 TQVWH D7:0 Data Out P2 A15:8 TWHQX 22.3.3 22.3.3.1 External IDE 16-bit Bus Cycles Definition of Symbols Table 155. External IDE 16-bit Bus Cycles Timing Symbol Definitions Signals A D L Q R W Address Data In ALE Data Out RD WR H L V X Z Conditions High Low Valid No Longer Valid Floating 189 4109JS–8051–10/06 22.3.3.2 Timings Test conditions: capacitive load on all pins= 50 pF. Table 156. External IDE 16-bit Bus Cycle - Data Read AC Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C Variable Clock Standard Mode Symbol TCLCL TLHLL TAVLL TLLAX TLLRL TRLRH TRHLH TAVDV TAVRL TRLDV TRLAZ TRHDX TRHDZ Parameter Clock Period ALE Pulse Width Address Valid to ALE Low Address hold after ALE Low ALE Low to RD Low RD Pulse Width RD high to ALE High Address Valid to Valid Data In Address Valid to RD Low RD Low to Valid Data RD Low to Address Float Data Hold After RD High Data Float After RD High 0 2·TCLCL-25 4·TCLCL-30 5·TCLCL-30 0 0 TCLCL-25 Min 50 2·TCLCL-15 TCLCL-20 TCLCL-20 3·TCLCL-30 6·TCLCL-25 TCLCL-20 TCLCL+20 9·TCLCL-65 2·TCLCL-30 2.5·TCLCL-30 0 Max Variable Clock X2 Mode Min 50 TCLCL-15 0.5·TCLCL-20 0.5·TCLCL-20 1.5·TCLCL-30 3·TCLCL-25 0.5·TCLCL-20 0.5·TCLCL+20 4.5·TCLCL-65 Max Unit ns ns ns ns ns ns ns ns ns ns ns ns ns Table 157. External IDE 16-bit Bus Cycle - Data Write AC Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C Variable Clock Standard Mode Symbol TCLCL TLHLL TAVLL TLLAX TLLWL TWLWH TWHLH TAVWL TQVWH TWHQX Parameter Clock Period ALE Pulse Width Address Valid to ALE Low Address hold after ALE Low ALE Low to WR Low WR Pulse Width WR High to ALE High Address Valid to WR Low Data Valid to WR High Data Hold after WR High Min 50 2·TCLCL-15 TCLCL-20 TCLCL-20 3·TCLCL-30 6·TCLCL-25 TCLCL-20 4·TCLCL-30 7·TCLCL-20 TCLCL-15 TCLCL+20 Max Variable Clock X2 Mode Min 50 TCLCL-15 0.5·TCLCL-20 0.5·TCLCL-20 1.5·TCLCL-30 3·TCLCL-25 0.5·TCLCL-20 2·TCLCL-30 3.5·TCLCL-20 0.5·TCLCL-15 0.5·TCLCL+20 Max Unit ns ns ns ns ns ns ns ns ns ns 190 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.3.3.3 Waveforms Figure 22-11. External IDE 16-bit Bus Cycle - Data Read Waveforms ALE TLHLL TLLRL TRLRH TRHLH RD TRLDV TRLAZ TAVLL P0 TLLAX A7:0 TAVRL TAVDV P2 A15:8 D15:8(1) Data In D7:0 Data In TRHDZ TRHDX Note: 1. D15:8 is written in DAT16H SFR. Figure 22-12. External IDE 16-bit Bus Cycle - Data Write Waveforms ALE TLHLL TLLWL TWLWH TWHLH WR TAVWL TAVLL P0 TLLAX A7:0 TQVWH D7:0 Data Out P2 A15:8 D15:8(1) Data Out TWHQX Note: 1. D15:8 is the content of DAT16H SFR. 22.4 SPI Interface Definition of Symbols Table 158. SPI Interface Timing Symbol Definitions Signals C I O Clock Data In Data Out H L V X Z Conditions High Low Valid No Longer Valid Floating 22.4.0.4 191 4109JS–8051–10/06 22.4.0.5 Timings Test conditions: capacitive load on all pins= 50 pF. Table 159. SPI Interface Master AC Timing VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol Parameter Slave Mode TCHCH TCHCX TCLCX TSLCH, TSLCL TIVCL, TIVCH TCLIX, TCHIX TCLOV, TCHOV TCLOX, TCHOX TCLSH, TCHSH TSLOV TSHOX TSHSL TILIH TIHIL TOLOH TOHOL Clock Period Clock High Time Clock Low Time SS Low to Clock edge Input Data Valid to Clock Edge Input Data Hold after Clock Edge Output Data Valid after Clock Edge Output Data Hold Time after Clock Edge SS High after Clock Edge SS Low to Output Data Valid Output Data Hold after SS High SS High to SS Low Input Rise Time Input Fall Time Output Rise time Output Fall Time Master Mode TCHCH TCHCX TCLCX TIVCL, TIVCH TCLIX, TCHIX TCLOV, TCHOV TCLOX, TCHOX TILIH TIHIL TOLOH TOHOL Clock Period Clock High Time Clock Low Time Input Data Valid to Clock Edge Input Data Hold after Clock Edge Output Data Valid after Clock Edge Output Data Hold Time after Clock Edge Input Data Rise Time Input Data Fall Time Output Data Rise time Output Data Fall Time 0 2 2 50 50 2 0.8 0.8 20 20 40 TPER TPER TPER ns ns ns ns μs μs ns ns (1) Min Max Unit 2 0.8 0.8 100 40 40 40 0 0 50 50 TPER TPER TPER ns ns ns ns ns ns ns ns 2 2 100 100 μs μs ns ns Note: 1. Value of this parameter depends on software. 192 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.4.0.6 Waveforms Figure 22-13. SPI Slave Waveforms (SSCPHA= 0) SS (input) TSLCH TSLCL SCK (SSCPOL= 0) (input) SCK (SSCPOL= 1) (input) TSLOV MISO (output) SLAVE MSB OUT TIVCH TCHIX TIVCL TCLIX MOSI (input) MSB IN BIT 6 LSB IN TCLOV TCHOV BIT 6 TCHCH TCLCH TCLSH TCHSH TSHSL TCHCX TCLCX TCHCL TCLOX TCHOX SLAVE LSB OUT (1) TSHOX Note: 1. Not Defined but generally the MSB of the character which has just been received. Figure 22-14. SPI Slave Waveforms (SSCPHA= 1) SS (input) TSLCH TSLCL SCK (SSCPOL= 0) (input) SCK (SSCPOL= 1) (input) TSLOV MISO (output) (1) TCHCH TCLCH TCLSH TCHSH TSHSL TCHCX TCLCX TCHCL TCHOV TCLOV BIT 6 TCHOX TCLOX SLAVE LSB OUT TSHOX SLAVE MSB OUT TIVCH TCHIX TIVCL TCLIX MOSI (input) MSB IN BIT 6 LSB IN Note: 1. Not Defined but generally the LSB of the character which has just been received. 193 4109JS–8051–10/06 Figure 22-15. SPI Master Waveforms (SSCPHA= 0) SS (output) TCHCH SCK (SSCPOL= 0) (output) SCK (SSCPOL= 1) (output) TCLCH TCHCX TCLCX TCHCL TIVCH TCHIX TIVCL TCLIX MSB IN BIT 6 TCLOV TCHOV LSB IN TCLOX TCHOX LSB OUT Port Data MOSI (input) MISO (output) Port Data MSB OUT BIT 6 Note: 1. SS handled by software using general purpose port pin. Figure 22-16. SPI Master Waveforms (SSCPHA= 1) SS(1) (output) TCHCH SCK (SSCPOL= 0) (output) SCK (SSCPOL= 1) (output) TCLCH TCHCX TCLCX TCHCL TIVCH TCHIX TIVCL TCLIX MOSI (input) MSB IN TCLOV BIT 6 TCLOX TCHOX BIT 6 LSB IN MISO (output) TCHOV Port Data MSB OUT LSB OUT Port Data Note: 1. SS handled by software using general purpose port pin. 22.4.1 22.4.1.1 Two-wire Interface Timings Table 160. TWI Interface AC Timing 194 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C VDD = 2.7 to 3.3 V, TA = -40 to +85°C INPUT Min Max 14·TCLCL(4) 16·TCLCL(4) 14·TCLCL(4) 1 μs 0.3 μs 250 ns 250 ns 250 ns 0 ns 14·TCLCL(4) 14·TCLCL(4) 14·TCLCL(4) 1 μs 0.3 μs OUTPUT Min Max 4.0 μs(1) 4.7 μs(1) 4.0 μs(1) -(2) 0.3 μs(3) 20·TCLCL(4)- TRD 1 μs(1) 8·TCLCL(4) 8·TCLCL(4) - TFC 4.7 μs(1) 4.0 μs(1) 4.7 μs(1) -(2) 0.3 μs(3) Symbol THD; STA TLOW THIGH TRC TFC TSU; DAT1 TSU; DAT2 TSU; DAT3 THD; DAT TSU; STA TSU; STO TBUF TRD TFD Parameter Start condition hold time SCL low time SCL high time SCL rise time SCL fall time Data set-up time SDA set-up time (before repeated START condition) SDA set-up time (before STOP condition) Data hold time Repeated START set-up time STOP condition set-up time Bus free time SDA rise time SDA fall time Notes: 1. At 100 kbit/s. At other bit-rates this value is inversely proportional to the bit-rate of 100 kbit/s. 2. Determined by the external bus-line capacitance and the external bus-line pull-up resistor, this must be < 1 μs. 3. Spikes on the SDA and SCL lines with a duration of less than 3·TCLCL will be filtered out. Maximum capacitance on bus-lines SDA and SCL= 400 pF. 4. TCLCL= TOSC= one oscillator clock period. 22.4.1.2 Waveforms Figure 22-17. Two Wire Waveforms START or Repeated START condition Trd SDA (INPUT/OUTPUT) Tfd Trc SCL (INPUT/OUTPUT) Thd;STA Tlow Thigh Tsu;DAT1 Thd;DAT Tsu;DAT2 Tfc Tsu;STO Tsu;DAT3 0.7 VDD 0.3 VDD Tbuf Repeated START condition START condition STOP condition Tsu;STA 0.7 VDD 0.3 VDD 195 4109JS–8051–10/06 22.4.2 22.4.2.1 MMC Interface Definition of symbols Table 161. MMC Interface Timing Symbol Definitions Signals C D O Clock Data In Data Out H L V X Conditions High Low Valid No Longer Valid 22.4.2.2 Timings Table 162. MMC Interface AC timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C, CL ≤ 100pF (10 cards) Symbol TCHCH TCHCX TCLCX TCLCH TCHCL TDVCH TCHDX TCHOX TOVCH Clock Period Clock High Time Clock Low Time Clock Rise Time Clock Fall Time Input Data Valid to Clock High Input Data Hold after Clock High Output Data Hold after Clock High Output Data Valid to Clock High 3 3 5 5 Parameter Min 50 10 10 10 10 Max Unit ns ns ns ns ns ns ns ns ns 22.4.2.3 Waveforms Figure 22-18. MMC Input-Output Waveforms TCHCH TCHCX MCLK TCHCL TCHIX MCMD Input MDAT Input TCHOX MCMD Output MDAT Output TOVCH TCLCH TIVCH TCLCX 196 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.4.3 22.4.3.1 Audio Interface Definition of symbols Table 163. Audio Interface Timing Symbol Definitions Signals C O S Clock Data Out Data Select H L V X Conditions High Low Valid No Longer Valid 22.4.3.2 Timings Table 164. Audio Interface AC timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C, CL≤ 30pF Symbol TCHCH TCHCX TCLCX TCLCH TCHCL TCLSV TCLOV Parameter Clock Period Clock High Time Clock Low Time Clock Rise Time Clock Fall Time Clock Low to Select Valid Clock Low to Data Valid 30 30 10 10 10 10 Min Max 325.5(1) Unit ns ns ns ns ns ns ns Note: 1. 32-bit format with Fs= 48 KHz. 22.4.3.3 Waveforms Figure 22-19. Audio Interface Waveforms TCHCH TCHCX DCLK TCHCL TCLSV DSEL TCLOV DDAT Right Left TCLCH TCLCX 197 4109JS–8051–10/06 22.4.4 22.4.4.1 Analog to Digital Converter Definition of symbols Table 165. Analog to Digital Converter Timing Symbol Definitions Signals C E S Clock Enable (ADEN bit) Start Conversion (ADSST bit) H L Conditions High Low 22.4.4.2 Characteristics Table 166. Analog to Digital Converter AC Characteristics VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol TCLCL TEHSH TSHSL DLe Parameter Clock Period Start-up Time Conversion Time Differential nonlinearity error(1)(2) Integral nonlinearity errorss(1)(3) Offset error(1)(4) Gain error(1)(5) Min 4 4 11·TCLCL 1 Max Unit μs μs μs LSB ILe OSe Ge 2 4 4 LSB LSB LSB Notes: 1. AVDD= AVREFP= 3.0 V, AVSS= AVREFN= 0 V. ADC is monotonic with no missing code. 2. The differential non-linearity is the difference between the actual step width and the ideal step width (see Figure 22-21). 3. The integral non-linearity is the peak difference between the center of the actual step and the ideal transfer curve after appropriate adjustment of gain and offset errors (see Figure 22-21). 4. The offset error is the absolute difference between the straight line which fits the actual transfer curve (after removing of gain error), and the straight line which fits the ideal transfer curve (see Figure 22-21). 5. The gain error is the relative difference in percent between the straight line which fits the actual transfer curve (after removing of offset error), and the straight line which fits the ideal transfer curve (see Figure 22-21). 198 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.4.4.3 Waveforms Figure 22-20. Analog to Digital Converter Internal Waveforms CLK TCLCL ADEN Bit TEHSH ADSST Bit TSHSL Figure 22-21. Analog to Digital Converter Characteristics Code Out Offset Gain Error Error OSe Ge 1023 1022 1021 1020 1019 1018 Ideal Transfer curve 7 6 5 4 3 2 1 0 0 1 LSB (ideal) 1 Offset Error OSe 2 3 4 5 6 7 Center of a step Example of an actual transfer curve Integral non-linearity (ILe) Differential non-linearity (DLe) 1018 1019 1020 1021 1022 1023 1024 AVIN (LSB ideal) 199 4109JS–8051–10/06 22.4.5 22.4.5.1 Flash Memory Definition of symbols Table 167. Flash Memory Timing Symbol Definitions Signals S R B ISP RST FBUSY flag L V X Conditions Low Valid No Longer Valid 22.4.5.2 Timings Table 168. Flash Memory AC Timing VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol TSVRL TRLSX TBHBL NFCY TFDR Parameter Input ISP Valid to RST Edge Input ISP Hold after RST Edge FLASH Internal Busy (Programming) Time Number of Flash Write Cycles Flash Data Retention Time 100K 10 Min 50 50 10 Typ Max Unit ns ns ms Cycle Years 22.4.5.3 Waveforms Figure 22-22. FLASH Memory - ISP Waveforms RST TSVRL ISP (1) TRLSX Note: 1. ISP must be driven through a pull-down resistor (see Section “In System Programming”, page 185). Figure 22-23. FLASH Memory - Internal Busy Waveforms FBUSY bit TBHBL 200 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 22.4.6 22.4.6.1 External Clock Drive and Logic Level References Definition of symbols Table 169. External Clock Timing Symbol Definitions Signals C Clock H L X Conditions High Low No Longer Valid 22.4.6.2 Timings External Clock AC Timings VDD = 2.7 to 3.3 V, TA = -40 to +85°C Symbol TCLCL TCHCX TCLCX TCLCH TCHCL TCR Clock Period High Time Low Time Rise Time Fall Time Cyclic Ratio in X2 mode Parameter Min 50 10 10 3 3 40 60 Max Unit ns ns ns ns ns % 22.4.6.3 Waveforms Figure 22-24. External Clock Waveform TCLCH VDD - 0.5 0.45 V VIH1 TCLCX TCHCL TCLCL TCHCX VIL Figure 22-25. AC Testing Input/Output Waveforms INPUTS VDD - 0.5 0.45 V 0.7 VDD 0.3 VDD OUTPUTS VIH min VIL max Note: 1. During AC testing, all inputs are driven at VDD -0.5 V for a logic 1 and 0.45 V for a logic 0. 2. Timing measurements are made on all outputs at VIH min for a logic 1 and VIL max for a logic 0. Figure 22-26. Float Waveforms VLOAD VLOAD + 0.1 V VLOAD - 0.1 V Timing Reference Points VOH - 0.1 V VOL + 0.1 V 201 4109JS–8051–10/06 Note: For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV change from the loading VOH/VOL level occurs with IOL/IOH= ±20 mA. 202 AT8xC51SND1C 4109JS–8051–10/06 AT8xC51SND1C 24. Ordering Information Memory Size 64K Flash 64K Flash 64K Flash 64K ROM 64K ROM 64K ROM ROMless ROMless ROMless Part Number AT89C51SND1C-ROTIL AT89C51SND1C-7HTIL AT89C51SND1C-DDV AT83SND1Cxxx(1)-ROTIL AT83SND1Cxxx(1)-7HTIL AT83SND1Cxxx-DDV AT80C51SND1C-ROTIL AT80C51SND1C-7HTIL AT80C51SND1C-DDV Supply Voltage 3V 3V 3V 3V 3V 3V 3V 3V 3V Temperature Range Industrial Industrial Industrial Industrial Industrial Industrial Industrial Industrial Industrial Max Frequency 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz Package(2) TQFP80 BGA81 Dice TQFP80 BGA81 Dice TQFP80 BGA81 Dice Packing Tray Tray Tray Tray Tray Tray Tray Tray Tray Product Marking 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL - AT89C51SND1C-ROTUL AT89C51SND1C-7HTJL AT83SND1Cxxx(1)-ROTUL AT83SND1Cxxx(1)-7HTJL AT80C51SND1C-ROTUL AT80C51SND1C-7HTJL 64K Flash 64K Flash 64K ROM 64K ROM ROMless ROMless 3V 3V 3V 3V 3V 3V Industrial & Green Industrial Industrial & Green Industrial & Green Industrial & Green Industrial & Green 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz TQFP80 BGA81 TQFP80 BGA81 TQFP80 BGA81 Tray Tray Tray Tray Tray Tray 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL 89C51SND1C-IL Notes: 1. Refers to ROM code. 2. PLCC84 package only available for development board. 203 4109JS–8051–10/06 A tmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Literature Requests www.atmel.com/literature Disclaimer: T he information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically providedotherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’sAtmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2006 . A ll rights reserved. A tmel ®, logo and combinations thereof, are registered trademarks, and Everywhere You Are ® are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4109JS–8051–10/06