ATA5021-TAPY

Features • • • • • • • • • • Low Current Consumption: IVDD < 25 µA RC Oscillator Internal Reset During Power-up and Supply Voltage Drops (POR) “Short” Trigger Window for Active Mode “Long” Trigger Window for Sleep Mode Cyclical Wake-up of the Microcontroller in Sleep Mode Trigger Input Single Wake-up Input Reset Output Enable Output Digital Window Watchdog Timer ATA5021 1. Description The digital window watchdog timer, ATA5021, is designed in Atmel®’s state-of-the-art 0.8 µm SOI technology SMART-I.S.™1. In applications where safety is critical, it is especially important to monitor the microcontroller. Normal microcontroller operation is indicated by a cyclically transmitted trigger signal, which is received by a window watchdog timer within a defined time window. A missing or a wrong trigger signal causes the watchdog timer to reset the microcontroller. The IC is tailored for microcontrollers, which can work in both full-power and sleep mode. With an additional voltage monitoring (power-on reset and supply voltage drop reset), the ATA5021 offers a complete monitoring solution for micro-systems in automotive and industrial applications. 9145D–AUTO–05/10 Figure 1-1. Block Diagram with External Circuit C VDD 10 nF R1 6 OSC 8 C1 Reset 5 RC oscillator OSC VDD Microcontroller Trigger 2 State machine OSC Input signal conditioning POR Power-on reset POR Test logic 4 Enable External switching circuitry Mode 3 Wake-up 1 GND 7 2 ATA5021 9145D–AUTO–05/10 ATA5021 2. Pin Configuration Figure 2-1. Pinning SO8 WUP TRIG MODE ENA 1 2 3 4 8 7 6 5 OSC GND VDD RESET Table 2-1. Pin 1 Pin Description Symbol WUP Function Wake-up input (pull-down resistor) There is one digitally debounced wake-up input. During the long watchdog window, each signal slope at the input initiates a reset pulse at pin 5. Trigger input (pull-up resistor) It is connected to the microprocessor’s trigger signal. Mode input (pull-up resistor) The processor’s mode signal initiates the switchover between the long and the short watchdog time. Enable output (push-pull) It is used for the control of peripheral components. It is activated after the processor triggers three times correctly. Reset output (open drain) Resets the processor in the case of under-voltage condition, a wrong trigger event or if a wake-up event occurs during long watchdog period. Supply voltage Ground, reference voltage RC oscillator 2 3 TRG MODE 4 ENA 5 6 7 8 RESET VDD GND OSC 3 9145D–AUTO–05/10 3. Functional Description 3.1 Supply Voltage, Pin 6 The ATA5021 requires a stabilized supply voltage VDD = 5V ±10% to comply with its electrical characteristics. An external buffer capacitor of C = 10 nF may be connected between pin 6 and GND. 3.2 RC Oscillator, Pin 8 The clock frequency, f, can be adjusted by the components R1 and C1 according to the formula: 1 f = -- with T T = 0.18 × (C1 + Cboard + 0.016) + 0.35 + [1.59 – (C1 + Cboard + 0.016)/85] × R1 × (C1 + Cboard + 0.016) R1 (kΩ) = external resistor at pin 8 C1 (nF) = external capacitor at pin 8 Cboard = 0.004 nF; this is the parasitic test board capacity caused by additional wiring on the test assembly. With frequency calculations of original boards, this parasitic capacitor can be omitted. Table 3-1. Comparison Table Clock Period Calculation versus Measurement on Test Board Period “T” (µs) by New Formula 4.36 8.20 17.26 74.40 156.30 13.45 25.99 55.57 242.10 509.25 18.92 36.69 78.63 343.03 721.70 27.38 53.22 114.25 498.94 1049.85 32.61 Period “T” (µs) by Measurement 4.33 8.30 17.10 74.50 152.00 13.25 26.13 55.00 241.50 505.00 18.50 36.63 78.25 341.25 700.00 26.75 53.25 112.50 497.50 1020.00 31.88 Deviation of New Formula versus Measurement –0.3% 1.8% 1.4% 1.5% –2.2% –0.4% 1.9% 1.2% 1.2% 1.6% –1.2% 0.8% 1.7% 0.6% –1.6% –1.4% 1.4% 1.5% 1.2% 0.0% –1.1% R1 (kΩ) 10.00 10.00 10.00 10.00 10.00 32.91 32.91 32.91 32.91 32.91 46.70 46.70 46.70 46.70 46.70 68.00 68.00 68.00 68.00 68.00 81.20 C1 (nF) 0.23 0.47 1.04 4.75 10.49 0.23 0.47 1.04 4.75 10.49 0.23 0.47 1.04 4.75 10.49 0.23 0.47 1.04 4.75 10.49 0.23 4 ATA5021 9145D–AUTO–05/10 ATA5021 Table 3-1. Comparison Table Clock Period Calculation versus Measurement on Test Board Period “T” (µs) by New Formula 63.47 136.32 595.56 1253.21 40.07 78.07 167.76 733.17 1542.84 47.81 93.20 200.37 875.90 1843.26 Period “T” (µs) by Measurement 63.75 135.00 592.50 1240.00 38.88 78.00 164.00 730.00 1530.00 46.38 93.00 200.25 870.00 1835.00 Deviation of New Formula versus Measurement 1.6% 1.9% 0.7% 1.3% –2.1% 1.2% –1.7% 0.9% 0.5% –1.7% 0.8% 1.1% 0.5% 0.9% R1 (kΩ) 81.20 81.20 81.20 81.20 100.00 100.00 100.00 100.00 100.00 119.50 119.50 119.50 119.50 119.50 C1 (nF) 0.47 1.04 4.75 10.49 0.23 0.47 1.04 4.75 10.49 0.23 0.47 1.04 4.75 10.49 The clock frequency determines all time periods of the logical part as shown in Section 7. “Electrical Characteristics” on page 9 under the subheading “Timing”. 3.3 Supply Voltage Monitoring, Pin 5 During ramp-up of the supply voltage and in the case of supply-voltage drops, the integrated power-on reset (POR) circuitry sets the internal logic to a defined basic status and generates a reset pulse at the reset output, pin 5. A hysteresis in the POR threshold prevents the circuit from oscillating. During ramp-up of the supply voltage, the reset output stays active for a specified period of time (t0) in order to bring the microcontroller into its defined reset status (see Figure 3-1 on page 5). 3.4 Switch-over Mode Time, Pin 3 The switch-over mode time enables the synchronous operation of microcontroller and watchdog. When the power-on reset time has elapsed, the watchdog has to be switched to monitoring mode by the microcontroller by a “low” signal transmitted to the mode pin (pin 3) within the time-out period, t1. If the low signal does not occur within t1 (see Figure 3-1 on page 5), the watchdog generates a reset pulse, t6, and t1 starts again. Microcontroller and watchdog are synchronized with the switch-over mode time, t1, each time a reset pulse is generated. Figure 3-1. Power-on Reset and Switch-over Mode VDD t0 Reset out t6 Pin 5 Pin 6 t1 Mode Pin 3 5 9145D–AUTO–05/10 3.5 3.5.1 Microcontroller in Active Mode Monitoring with the “Short” Trigger Window After the switch-over mode, the watchdog operates in short watchdog mode and expects a trigger pulse from the microcontroller within the defined time window, t 3 , (enable time). The watchdog generates a reset pulse which resets the microcontroller if: • the trigger pulse duration is too long • the trigger pulse is within the disable time, t2 • there is no trigger pulse Figure 3-2 shows the pulse diagram with a missing trigger pulse. Figure 3-2. Pulse Diagram with no Trigger Pulse during the Short Watchdog Time VDD t0 Reset out t2 Mode t3 Pin 3 t1 Pin 5 Pin 6 Trigger Pin 2 Figure 3-3 shows a correct trigger sequence. The positive edge of the trigger signal starts a new monitoring cycle with the disable time, t2. To ensure correct operation of the microcontroller, the watchdog needs to be triggered three times correctly before it sets its enable output. This feature is used to activate or deactivate safety-critical components, which have to be switched to a certain condition (emergency status) in the case of a microcontroller malfunction. As soon as there is an incorrect trigger sequence, the enable signal is reset and it takes a sequence of three correct triggers before enable is active. For proper operation, the trigger pulse duration must be longer than the input signal debounce time (see item 4.2 in Section 7. “Electrical Characteristics” on page 9) and must not exceed the maximum duration of 45 clock cycles (see item 4.4 in Section 7. “Electrical Characteristics” on page 9). Figure 3-3. Pulse Diagram of a Correct Trigger Sequence during the Short Watchdog Time VDD t0 Reset out t2 Mode t1 Pin 5 t2 Pin 3 Pin 6 t3 Trigger ttrig Enable Pin 2 Pin 4 6 ATA5021 9145D–AUTO–05/10 ATA5021 3.6 3.6.1 Microcontroller in Sleep Mode Monitoring with the “Long” Trigger Window The long watchdog mode allows cyclical wake-up of the microcontroller during sleep mode. As in short watchdog mode, there is a disable time, t4, and an enable time, t5, in which a trigger signal is accepted. The watchdog can be switched from the short trigger window to the long trigger window with a “high” potential at the mode pin (pin 3). In contrast to the short watchdog mode, the time periods are now much longer and the enable output remains inactive so that other components can be switched off to effect a further decrease in current consumption. As soon as a wake-up signal at the wake-up input (pins 1) is detected, the long watchdog mode ends, a reset pulse wakes-up the sleeping microcontroller and the normal monitoring cycle starts with the mode switch-over time. Figure 3-4 shows the switch-over from the short to the long watchdog mode. The wake-up signal during the enable time, t5, activates a reset pulse, t6. The watchdog can be switched back from the long to the short watchdog mode with a low potential at the mode pin (pin 3). Figure 3-4. Pulse Diagram of the Long Watchdog Time t6 Reset out Pin 5 Wake-up t4 Mode t2 Trigger Pin 2 t5 Pin 3 Pin 1 t1 Enable Pin 4 3.7 Reset-Out, Pin 5 The Reset-out pin functionality is guaranteed for supply voltage down to 1V. In case of a voltage drop, the microcontroller gets a reset up to that value. 7 9145D–AUTO–05/10 4. State Diagram The kernel of the watchdog is a finite state machine. Figure 4-1 shows the state diagram with all possible states and transmissions. Many transmissions are controlled by an internal timer. The numbers for the time-outs are the same as on the pulse diagrams. Figure 4-1. State Diagram of the Finite State Machine Reset State time-out t0 mode_d = 0 mode_d = 1 Mode Switch State Short Window Disable State mode_d = 0 Long Window Disable State mode_d = 1 time-out t1 trg_ok trg_d = 0 mode_d = 0 time-out t2 time-out t4 trg_ok time-out t6 time-out t3 OR trg_err Short Window Enable State time-out t5 OR trg_err OR wedge Long Window Disable State Reset Out State trg_d = 0 OR wedge Notes: 1. mode_d and trg_d are the debounced signals of the MODE and TRG pins 2. wedge is the detection of a signal edge on the wake-up pin after the deboucing time 3. trg_ok is valid for once cycle after the rising edge on trg_d 4. trg_err is valid if the low period of trg_d is too long 8 ATA5021 9145D–AUTO–05/10 ATA5021 5. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Voltage range on pin VDD Voltage range on pins Output current HBM ESD ANSI/ESD-STM5.1 JESD22-A114 AEC-Q100 (002) Ambient temperature range Storage temperature range Pin Symbol VVDD,max VIO,max IOUT,max VESD,HBM Tamb Tsto Min. –0.4 –0.4 –2 Max. +6.5 VVDD + 0.4 +2 Unit V V mA ±2 kV –40 –55 +125 +150 °C °C 6. Thermal Resistance Parameters Thermal case resistance junction ambient Symbol RthJA Value 180 Unit K/W 7. Electrical Characteristics VVDD = 5V, Tamb = –40°C to +125°C, reference point is pin 7, unless otherwise specified. No. Parameters Test Conditions VVDD = 5V R1 = 66 kΩ C1 = 470 pF Release reset state with rising supply voltage Get reset state with falling supply voltage VVDD = 1V to VPOR1 IRTO = 300 µA VVDD = 5V VVDD = 5V VVDD = 5V VIN = 5V VVDD = 5V VIN = 0V VVDD = 5V Pin Symbol Min. Typ. Max. Unit Type* Power Supply 1.1 Current Consumption 6 IVDD VPOR1 VPOR2 VPOR,hys VRST 3.9 3.8 40 25 µA A 1.2 Power-on-reset 1.3 1.4 1.5 Inputs 2.1 2.2 2.3 2.4 2.5 Logical “high” Logical “low” Hysteresis Pull-down current Pull-up current POR hysteresis Reset Level for low VDD 6 6 6 5 4.5 4.4 200 0.1 V V mV VVDD A A A A 1, 2, 3 1, 2, 3 1, 2, 3 1 2, 3 VIH VIL VIN_hys IPD IPU 3.4 1.6 0.6 5 –20 1 1.4 20 –5 V V V µA µA A A A A A *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter Notes: 1. Frequency deviation also depends on the tolerances of the external components 2. Cycle = Period of clock frequency (see Section 3.2 on page 4) 9 9145D–AUTO–05/10 7. Electrical Characteristics (Continued) VVDD = 5V, Tamb = –40°C to +125°C, reference point is pin 7, unless otherwise specified. No. Outputs 3.1 3.2 3.3 3.4 Timing 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 Notes: R1 = 66 kΩ Frequency deviation (1) C1 = 470 pF VVDD = 4.5V to 5V(2) Debounce time Maximum trigger pulse length Power-up reset time Switch-over mode time Disable time Enable time Disable time Enable time Reset-out time Short watchdog window Short watchdog window Long watchdog window Long watchdog window 8 2,3 1 3 fdev tdeb1 tdeb2 ttrgmax t0 t1 t2 t3 t4 t5 t6 3 96 45 201 1112 130 124 71970 30002 40 5 4 128 % Cycle Cycle Cycle Cycle Cycle Cycle Cycle Cycle Cycle Cycle C D D D D D D D D D D Maximum output current Logical output “low” Logical output “high” Leakage current IOUT = 1 mA IOUT = –1 mA VOUT = 5V 4, 5 4, 5 4 5 IOUT VOL VOH Ileak VVDD – 0.2 2 –2 +2 0.2 mA V V µA C A A A Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type* *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter 1. Frequency deviation also depends on the tolerances of the external components 2. Cycle = Period of clock frequency (see Section 3.2 on page 4) 10 ATA5021 9145D–AUTO–05/10 ATA5021 8. Ordering Information Extended Type Number ATA5021-TAPY ATA5021-TAQY Package SO8 SO8 Remarks Taped and reeled, Pb-free, small reel Taped and reeled, Pb-free, big reel 9. Package Information Package: SO 8 Dimensions in mm 4.9±0.1 5±0.2 3.7±0.1 0.2 0.1+0.15 1.4 0.4 1.27 3.81 3.8±0.1 6±0.2 8 5 technical drawings according to DIN specifications 1 Drawing-No.: 6.541-5031.01-4 Issue: 1; 15.08.06 4 11 9145D–AUTO–05/10 10. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 9145D-AUTO-05/10 9145C-AUTO-09/09 History • Section 3.2 “RC Oscillator, Pin 8” on pages 4 to 5 changed • Section 3.2 “RC Oscillator, Pin 8” on page 4 changed • El. Char. Table: rows 3.1, 3.2, 3.3 changed • • • • Put datasheet in the newest template Section 3.2 “”RC Oscillator, Pin 8” on pages 4 to 6 updated Section 3.5 “Microcontroller in Active Mode” on page 7 updated Section 7 “Electrical Characteristics” numbers 1.1 and 4.1 on pages 10 to 11 updated 9145B-AUTO-05/09 12 ATA5021 9145D–AUTO–05/10 Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 International Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon Hong Kong Tel: (852) 2245-6100 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support auto_control@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: T he information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2010 Atmel Corporation. All rights reserved. A tmel ®, logo and combinations thereof, and others are registered trademarks. SMART-I.S. ™ a nd others are trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 9145D–AUTO–05/10