ATMEGA88-15MT2

Appendix A - ATmega88/168 Automotive specification at 150°C This document contains information specific to devices operating at temperatures up to 150°C. Only deviations are covered in this appendix, all other information can be found in the complete Automotive datasheet. The complete Automotive datasheet can be found on www.atmel.com 8-bit Microcontroller with 8K Bytes In-System Programmable Flash ATmega88/168 Automotive Appendix A PRELIMINARY Electrical Characteristics Absolute Maximum Ratings* Operating Temperature.................................. -55°C to +150°C Storage Temperature ..................................... -65°C to +175°C Voltage on any Pin except RESET with respect to Ground ................................-0.5V to VCC+0.5V Voltage on RESET with respect to Ground......-0.5V to +13.0V Maximum Operating Voltage ............................................ 6.0V DC Current per I/O Pin ............................................... 30.0 mA DC Current VCC and GND Pins................................ 200.0 mA *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Characteristics Symbol VIL VIH VIL1 VIH1 VIL2 VIH2 VIL3 VIH3 VOL VOH IIL IIH RRST RPU Parameter TA = -40°C to 150°C, VCC = 2.7V to 5.5V (unless otherwise noted) Condition VCC = 2.7V - 5.5V VCC = 2.7V - 5.5V VCC = 2.7V - 5.5V VCC = 2.7V - 5.5V VCC = 2.7V - 5.5V VCC = 2.7V - 5.5V VCC = 2.7V - 5.5V VCC = 2.7V - 5.5V IOL = 20mA, VCC = 5V IOL = 5mA, VCC = 3V IOH = -20mA, VCC = 5V IOH = -10mA, VCC = 3V VCC = 5.5V, pin low (absolute value) VCC = 5.5V, pin high (absolute value) 30 20 4.0 2.2 1 1 60 50 Min. -0.5 0.6VCC(2) -0.5 0.7VCC(2) -0.5 0.9VCC(2) -0.5 0.6VCC(2) Typ. Max. 0.3VCC(1) VCC + 0.5 0.1VCC(1) VCC + 0.5 0.2VCC(1) VCC + 0.5 0.3VCC(1) VCC + 0.5 0.8 0.5 Units V V V V V V V V V V µA µA kΩ kΩ Input Low Voltage, except XTAL1 and RESET pin Input High Voltage, except XTAL1 and RESET pins Input Low Voltage, XTAL1 pin Input High Voltage, XTAL1 pin Input Low Voltage, RESET pin Input High Voltage, RESET pin Input Low Voltage, RESET pin as I/O Input High Voltage, RESET pin as I/O Output Low Voltage(3), I/O pin except RESET Output High Voltage(4), I/O pin except RESET Input Leakage Current I/O Pin Input Leakage Current I/O Pin Reset Pull-up Resistor I/O Pin Pull-up Resistor 2 ATMega88/168 Automotive 7607F–AVR–03/08 ATMega88/168 Automotive TA = -40°C to 150°C, VCC = 2.7V to 5.5V (unless otherwise noted) (Continued) Symbol ICC Power Supply Current(6) ICC IDLE Parameter Condition Active 4MHz, VCC = 3V Active 8MHz, VCC = 5V Active 16MHz, VCC = 5V Idle 4MHz, VCC = 3V Idle 8MHz, VCC = 5V Idle 16MHz, VCC = 5V WDT enabled, VCC = 3V WDT enabled, VCC = 5V WDT disabled, VCC = 3V WDT disabled, VCC = 5V Analog Comparator Input Offset Voltage Analog Comparator Input Leakage Current Analog Comparator Propagation Delay VCC = 5V Vin = VCC/2 VCC = 5V Vin = VCC/2 VCC = 4.0V -50 500