ATR0809-PRQG

Features • • • • • • • • • • • • Current-controlled Output Current Source with 4 Input Channels Two Selectable Outputs for Grounded Laser Diodes Up to 350 mA Output Current per Channel Total Output Current up to 500 mA On-chip RF Oscillator Oscillator Frequency Range from 200 MHz to 500 MHz Individual Setting of RF Oscillator Current on Each Output by External Resistors Maximum Oscillator Current Amplitude 100 mA Single 5 V Power Supply Common Enable/Disable Input TTL/CMOS Compatible Control Signals Small Pb-free QFN20 or SSO20 Package Applications • • • • DVD-ROM with CD-RW Capability DVD+RW with CD-RW Capability DVD-RW with CD-RW Capability Magneto-optical Drives and Others Four Channel Laser Driver with RF Oscillator and Two Outputs ATR0809 Summary Description ATR0809 is a laser diode driver for the operation of two different grounded laser diodes for DVD-RW/+RW (650 nm) and CD-RW (780 nm). It includes four channels for four different optical power levels. All channels (channel 1 = read channel, channel 2, 3, 4 = write channels) can be controlled by fast switches. The current pulses are enabled when a low signal is applied to the NE pins. All channels are summed together and switched to one of the two outputs IOUTA or IOUTB by the select input SELA. Each write channel (channel 2, 3 and 4) can contribute up to 350 mA to the total output current of up to 500 mA. The read channel can contribute up to 150 mA. Total gains of 100 (read channel), 250 (channel 2 and 3) and 100 (channel 4) are provided between each reference current input and the selected output. Although the reference inputs are current inputs, voltage control is also possible by using external resistors. An on-chip RF oscillator can be used to reduce laser mode hopping noise in read mode. The oscillator current amplitude and frequency can be set independently for the two selectable outputs with four different resistors. Oscillation is enabled by a high signal at the ENOSC pin. Complete shutdown of the output currents is achieved by a low signal at the ENABLE input. Rev. 4792BS–DVD–05/04 Figure 1. Block Diagram I4 NE4 I3 NE3 I2 NE2 Channel 4 Channel 3 IOUTA IOUTB Channel 2 IR NER ENABLE Channel 1 Read channel ENOSC RF oscillator RFA RSA RFB RSB SELA 2 ATR0809 4792BS–DVD–05/04 ATR0809 Pin Configuration SSO20 Figure 2. Pinning SSO20 IR I2 I3 I4 RFA RFB NER NE2 NE3 NE4 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VCC ENABLE IOUTA GND RSA RSB IOUTB SELA VCC ENOSC Pin Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol IR I2 I3 I4 RFA RFB NER NE2 NE3 NE4 ENOSC VCC SELA IOUTB RSB RSA GND IOUTA ENABLE VCC Type Analog Analog Analog Analog Analog Analog Digital Digital Digital Digital Digital Supply Digital Analog Analog Analog Supply Analog Digital Supply Function Input current, bias voltage approximately GND Input current, bias voltage approximately GND Input current, bias voltage approximately GND Input current, bias voltage approximately GND External resistor to GND sets frequency of oscillator A External resistor to GND sets frequency of oscillator B Digital control of channel 1 (read, active low) Digital control of channel 2 (active low) Digital control of channel 3 (active low) Digital control of channel 4 (active low) Enables RF oscillator (active high) 5 V power supply High: selects IOUTA, RSA, RFA Low: selects IOUTB, RSB, RFB Output current source B for laser diode External resistor to GND sets swing of oscillator B External resistor to GND sets swing of oscillator A Ground Output current source A for laser diode Enables output current (active high) 5 V power supply 3 4792BS–DVD–05/04 Pin Configuration QFN20 Figure 3. Pinning QFN20 I3 I2 IR VCC ENABLE I4 RFA RFB NER NE2 1 2 3 4 5 20 19 18 17 16 15 14 13 12 11 6 7 8 9 10 IOUTA GND RSA RSB IOUTB Pin Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol I4 RFA RFB NER NE2 NE3 NE4 ENOSC VCC SELA IOUTB RSB RSA GND IOUTA ENABLE VCC IR I2 I3 Type Analog Analog Analog Digital Digital Digital Digital Digital Supply Digital Analog Analog Analog Supply Analog Digital Supply Analog Analog Analog Function Input current, bias voltage approximately GND External resistor to GND sets frequency of oscillator A External resistor to GND sets frequency of oscillator B Digital control of channel 1 (read, active low) Digital control of channel 2 (active low) Digital control of channel 3 (active low) Digital control of channel 4 (active low) Enables RF oscillator (active high) 5 V power supply High: selects IOUTA, RSA, RFA Low: selects IOUTB, RSB, RFB Output current source B for laser diode External resistor to GND sets swing of oscillator B External resistor to GND sets swing of oscillator A Ground Output current source A for laser diode Enables output current (active high) 5 V power supply Input current, bias voltage approximately GND Input current, bias voltage approximately GND Input current, bias voltage approximately GND 4 ATR0809 4792BS–DVD–05/04 NE3 NE4 ENOSC VCC SELA ATR0809 Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Supply voltage Input voltage at any input Power dissipation Output voltage Junction temperature Storage temperature Notes: 1. RthJA ≤115 K/W at Tamb = 70°C 2. RthJA ≤115 K/W at Tamb = 25°C Symbol VCC Vin Pmax Vout Tj Tstg Value -0.5 to +6.0 -0.5 to VCC +0.5 0.7 (1) Unit V V W V °C °C to 1 (2) -0.5 to VCC -1 150 -65 to +125 Thermal Resistance Parameters Junction case Junction ambient Note: Symbol RthJC RthJA Value 27 125(1) Unit K/W K/W 1. Measured with multi-layer test board (JEDEC standard) Recommended Operating Conditions Parameters Supply voltage Input current External resistor to GND to set oscillator frequency External resistor to GND to set oscillator swing Operating temperature range Symbol VCC IIR, II2, II3, II4 RFA, RFB RSA, RSB Tamb Value 4.5 to 5.5 < 2.5 >3 >1 0 to +70 Unit V mA kΩ kΩ °C 5 4792BS–DVD–05/04 Ordering Information Extended Type Number ATR0809-TKQG ATR0809-PRQG Package PB-free SSO20 PB-free QFN20 (4 mm x 4 mm) Remarks Taped and reeled Tuped and reeled Package Information Package SSO20 Dimensions in mm 6.75 6.50 5.7 5.3 4.5 4.3 1.30 0.25 0.65 5.85 20 11 0.15 0.05 0.15 6.6 6.3 technical drawings according to DIN specifications 1 10 6 ATR0809 4792BS–DVD–05/04 ATR0809 7 4792BS–DVD–05/04 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Literature Requests www.atmel.com/literature Disclaimer: A tmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. © Atmel Corporation 2004 . A ll rights reserved. A tmel ® a nd combinations thereof are the registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others. Printed on recycled paper. 4792BS–DVD–05/04