ATXMEGA256A3-AU

Features • High-performance, Low-power AVR 8/16-bit XMEGA Microcontroller • Non-volatile Program and Data Memories – 64K - 256K Bytes of In-System Self-Programmable Flash – 4K - 8K Boot Code Section with Independent Lock Bits – 2K - 4K Bytes EEPROM – 4K - 16K Bytes Internal SRAM Peripheral Features – Four-channel DMA Controller with support for external requests – Eight-channel Event System – Seven 16-bit Timer/Counters Four Timer/Counters with 4 Output Compare or Input Capture channels Three Timer/Counters with 2 Output Compare or Input Capture channels High Resolution Extensions on all Timer/Counters Advanced Waveform Extension on one Timer/Counter – Seven USARTs IrDA Extension on 1 USART – AES and DES Crypto Engine – Two Two-wire Interfaces with dual address match(I2C and SMBus compatible) – Three SPI (Serial Peripheral Interfaces) – 16-bit Real Time Counter with Separate Oscillator – Two Eight-channel, 12-bit, 2 Msps Analog to Digital Converters – One Two-channel, 12-bit, 1 Msps Digital to Analog Converter – Four Analog Comparators with Window compare function – External Interrupts on all General Purpose I/O pins – Programmable Watchdog Timer with Separate On-chip Ultra Low Power Oscillator Special Microcontroller Features – Power-on Reset and Programmable Brown-out Detection – Internal and External Clock Options with PLL – Programmable Multi-level Interrupt Controller – Sleep Modes: Idle, Power-down, Standby, Power-save, Extended Standby – Advanced Programming, Test and Debugging Interfaces JTAG (IEEE 1149.1 Compliant) Interface for test, debug and programming PDI (Program and Debug Interface) for programming, test and debugging I/O and Packages – 50 Programmable I/O Lines – 64-lead TQFP – 64-pad MLF Operating Voltage – 1.6 – 3.6V Speed performance – 0 – 12 MHz @ 1.6 – 3.6V – 0 – 32 MHz @ 2.7 – 3.6V • 8/16-bit XMEGA A3 Microcontroller ATxmega256A3 ATxmega192A3 ATxmega128A3 ATxmega64A3 Preliminary • • • • Typical Applications • • • • • Industrial control Factory automation Building control Board control White Goods • • • • • Climate control ZigBee Motor control Networking Optical • • • • • Hand-held battery applications Power tools HVAC Metering Medical Applications 8068E–AVR–08/08 XMEGA A3 1. Ordering Information Ordering Code ATxmega256A3-AU ATxmega192A3-AU ATxmega128A3-AU ATxmega64A3-AU ATxmega256A3-MU ATxmega192A3-MU ATxmega128A3-MU ATxmega64A3-MU Notes: 1. 2. 3. Flash (B) 256K + 8K 192K + 8K 128K + 8K 64K + 4K 256K + 8K 192K + 8K 128K + 8K 64K + 4K E2 (B) 4K 4K 2K 2K 4K 4K 2K 2K SRAM (B) 16K 16K 8K 4K 16K 16K 8K 4K Speed (MHz) 32 32 32 32 32 32 32 32 Power Supply 1.6 - 3.6V 1.6 - 3.6V 1.6 - 3.6V 1.6 - 3.6V 1.6 - 3.6V 1.6 - 3.6V 1.6 - 3.6V 1.6 - 3.6V Package(1)(2)(3) Temp 64A -40⋅ - 85⋅C 64M1 This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. For packaging information, see ”Packaging information” on page 66. Package Type 64A 64M1 64-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) 64-pad, 9 x 9 x 1.0 mm Body, Lead Pitch 0.50 mm, 5.40 mm Exposed Pad, Micro Lead Frame Package (MLF) 2. Pinout/Block Diagram Figure 2-1. Block diagram and TQFP-pinout. PA2 PA1 PA0 AVCC GND PR1 PR0 RESET/PDI_CLK PDI_DATA PF7 PF6 VCC GND PF5 PF4 PF3 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 INDEX CORNER PA3 PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 GND VCC PC0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Port R DATA BU S ADC A OSC/CLK Control Port A BOD TEMP VREF RTC POR OCD AC A0 Power Control AC A1 ADC B FLASH CPU RAM E2PROM Port B DAC B AC B0 Reset Control DMA Interrupt Controller Watchdog Event System ctrl DATA BU S EVENT ROUTING NETWORK AC B1 Port C Port D Port E Port F PF2 PF1 PF0 VCC GND PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 VCC GND PD7 USART0:1 USART0:1 USART0:1 T/C0:1 Note: 1. For full details on pinout and alternate pin functions refer to ”Pinout and Pin Functions” on page 48. PC1 PC2 PC3 PC4 PC5 PC6 PC7 GND VCC PD0 PD1 PD2 PD3 PD4 PD5 PD6 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SPI USART0 T/C0:1 T/C0:1 T/C0 TWI TWI SPI SPI 2 8068E–AVR–08/08 XMEGA A3 3. Overview The XMEGA A3 is a family of low power, high performance and peripheral rich CMOS 8/16-bit microcontrollers based on the AVR ® e nhanced RISC architecture. By executing powerful instructions in a single clock cycle, the XMEGA A3 achieves throughputs approaching 1 Million Instructions Per Second (MIPS) per MHz allowing the system designer to optimize power consumption versus processing speed. The AVR CPU combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction, executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs many times faster than conventional single-accumulator or CISC based microcontrollers. The XMEGA A3 devices provide the following features: In-System Programmable Flash with Read-While-Write capabilities, Internal EEPROM and SRAM, four-channel DMA Controller, eight-channel Event System, Programmable Multi-level Interrupt Controller, 50 general purpose I/O lines, 16-bit Real Time Counter (RTC), seven flexible 16-bit Timer/Counters with compare modes and PWM, seven USARTs, two Two Wire Serial Interfaces (TWIs), three Serial Peripheral Interfaces (SPIs), AES and DES crypto engine, two 8-channel 12-bit ADCs with optional differential input with programmable gain, one 2-channel 12-bit DACs, four analog comparators with window mode, programmable Watchdog Timer with separate Internal Oscillator, accurate internal oscillators with PLL and prescaler and programmable Brown-Out Detection. The Program and Debug Interface (PDI), a fast 2-pin interface for programming and debugging, is available. The devices also have an IEEE std. 1149.1 compliant JTAG test interface, and this can also be used for On-chip Debug and programming. The XMEGA A3 devices have five software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, DMA Controller, Event System, Interrupt Controller and all peripherals to continue functioning. The Power-down mode saves the SRAM and register contents but stops the oscillators, disabling all other functions until the next TWI or pin-change interrupt, or Reset. In Power-save mode, the asynchronous Real Time Counter continues to run, allowing the application to maintain a timer base while the rest of the device is sleeping. In Standby mode, the Crystal/Resonator Oscillator is kept running while the rest of the device is sleeping. This allows very fast start-up from external crystal combined with low power consumption. In Extended Standby mode, both the main Oscillator and the Asynchronous Timer continue to run. To further reduce power consumption, the peripheral clock for each individual peripheral can optionally be stopped in Active mode and Idle sleep mode. The device is manufactured using Atmel's high-density nonvolatile memory technology. The program Flash memory can be reprogrammed in-system through the PDI or JTAG. A Bootloader running in the device can use any interface to download the application program to the Flash memory. The Bootloader software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8/16-bit RISC CPU with In-System Self-Programmable Flash, the Atmel XMEGA A3 is a powerful microcontroller family that provides a highly flexible and cost effective solution for many embedded applications. The XMEGA A3 devices are supported with a full suite of program and system development tools including: C compilers, macro assemblers, program debugger/simulators, programmers, and evaluation kits. 3 8068E–AVR–08/08 XMEGA A3 3.1 Block Diagram XMEGA A3 Block Diagram PR[0..1] XTAL1 XTAL2 Figure 3-1. PORT R (2) Oscillator Circuits/ Clock Generation Watchdog Oscillator Real Time Counter Watchdog Timer DATA BUS PA[0..7] PORT A (8) ACA ADCA AREFA Internal Reference AREFB Event System Controller SRAM DMA Controller Oscillator Control Sleep Controller Power Supervision POR/BOD & RESET VCC GND RESET/ PDI_CLK PDI_DATA PDI BUS Controller Prog/Debug Controller JTAG DES CPU AES Interrupt Controller OCD PORT B ADCB ACB PB[0..7]/ JTAG USARTF0 TCF0 EEPROM PORT B (8) Flash DACB PORT F (8) NVM Controller PF[0..7] IRCOM DATA BUS EVENT ROUTING NETWORK USARTC0:1 USARTD0:1 USARTE0:1 TCC0:1 TCD0:1 TCE0:1 TWIC TWIE SPIC SPID SPIE To Clock Generator PORT C (8) PORT D (8) PORT E (8) TOSC1 TOSC2 PC[0..7] PD[0..7] PE[0..7] 4 8068E–AVR–08/08 XMEGA A3 4. Resources A comprehensive set of development tools, application notes and datasheets are available for download on http://www.atmel.com/avr. 4.1 Recommended reading • XMEGA A Manual • XMEGA A Application Notes This device data sheet only contains part specific information and a short description of each peripheral and module. The XMEGA A Manual describes the modules and peripherals in depth. The XMEGA A application notes contain example code and show applied use of the modules and peripherals. The XMEGA A Manual and Application Notes are available from http://www.atmel.com/avr. 5. Disclaimer For devices that are not available yet, typical values contained in this datasheet are based on simulations and characterization of other AVR XMEGA microcontrollers manufactured on the same process technology. Min. and Max values will be available after the device is characterized. 5 8068E–AVR–08/08 XMEGA A3 6. AVR CPU 6.1 Features • 8/16-bit high performance AVR RISC Architecture – 138 instructions – Hardware multiplier 32x8-bit registers directly connected to the ALU Stack in RAM Stack Pointer accessible in I/O memory space Direct addressing of up to 16M bytes of program and data memory True 16/24-bit access to 16/24-bit I/O registers Support for 8-, 16- and 32-bit Arithmetic Configuration Change Protection of system critical features • • • • • • • 6.2 Overview The XMEGA A3 uses an 8/16-bit AVR CPU. The main function of the AVR CPU is to ensure correct program execution. The CPU must therefore be able to access memories, perform calculations and control peripherals. Interrupt handling is described in a separate section. Figure 6-1 on page 6 shows the CPU block diagram. Figure 6-1. CPU block diagram DATA BUS Program Counter Flash Program Memory 32 x 8 General Purpose Registers OCD Instruction Register STATUS/ CONTROL Instruction Decode ALU Multiplier/ DES DATA BUS Peripheral Module 1 Peripheral Module 2 SRAM EEPROM PMIC The AVR uses a Harvard architecture - with separate memories and buses for program and data. Instructions in the program memory are executed with a single level pipeline. While one instruction is being executed, the next instruction is pre-fetched from the program memory. 6 8068E–AVR–08/08 XMEGA A3 This concept enables instructions to be executed in every clock cycle. The program memory is In-System Re-programmable Flash memory. 6.3 Register File The fast-access Register File contains 32 x 8-bit general purpose working registers with a single clock cycle access time. This allows single-cycle Arithmetic Logic Unit (ALU) operation. In a typical ALU operation, two operands are output from the Register File, the operation is executed, and the result is stored back in the Register File - in one clock cycle. Six of the 32 registers can be used as three 16-bit indirect address register pointers for Data Space addressing - enabling efficient address calculations. One of these address pointers can also be used as an address pointer for look up tables in Flash program memory. 6.4 ALU - Arithmetic Logic Unit The high performance Arithmetic Logic Unit (ALU) supports arithmetic and logic operations between registers or between a constant and a register. Single register operations can also be executed. Within a single clock cycle, arithmetic operations between general purpose registers or between a register and an immediate are executed. After an arithmetic or logic operation, the Status Register is updated to reflect information about the result of the operation. The ALU operations are divided into three main categories – arithmetic, logical, and bit-functions. Both 8- and 16-bit arithmetic is supported, and the instruction set allows for easy implementation of 32-bit arithmetic. The ALU also provides a powerful multiplier supporting both signed and unsigned multiplication and fractional format. 6.5 Program Flow When the device is powered on, the CPU starts to execute instructions from the lowest address in the Flash Program Memory ‘0’. The Program Counter (PC) addresses the next instruction to be fetched. After a reset, the PC is set to location ‘0’. Program flow is provided by conditional and unconditional jump and call instructions, capable of addressing the whole address space directly. Most AVR instructions use a 16-bit word format, while a limited number uses a 32-bit format. During interrupts and subroutine calls, the return address PC is stored on the Stack. The Stack is effectively allocated in the general data SRAM, and consequently the Stack size is only limited by the total SRAM size and the usage of the SRAM. After reset the Stack Pointer (SP) points to the highest address in the internal SRAM. The SP is read/write accessible in the I/O memory space, enabling easy implementation of multiple stacks or stack areas. The data SRAM can easily be accessed through the five different addressing modes supported in the AVR CPU. 7 8068E–AVR–08/08 XMEGA A3 7. Memories 7.1 Features • Flash Program Memory – One linear address space – In-System programmable – Self-Programming and Bootloader support – Application Section for application code – Application Table Section for application code or data storage – Boot Section for application code or bootloader code – Separate lock bits and protection for all sections • Data Memory – One linear address space – Single cycle access from CPU – SRAM – EEPROM Byte or page accessible Optional memory mapping for direct load and store – I/O Memory Configuration and Status register for all peripherals and modules 16-bit accessible General Purpose Register for global variables or flags – External Memory support – Bus arbitration Safe and deterministic handling of CPU and DMA Controller priority – Separate buses for SRAM, EEPROM, I/O Memory and External Memory access Simultaneous bus access for CPU and DMA Controller • Calibration Row Memory for factory programmed data Oscillator calibration bytes Serial number Device ID for each device type • User Signature Row One flash page in size Can be read and written from software Data is kept after Chip Erase 7.2 Overview The AVR architecture has two main memory spaces, the Program Memory and the Data Memory. In addition, the XMEGA A3 features an EEPROM Memory for non-volatile data storage. All three memory spaces are linear and require no paging. The available memory size configurations are shown in ”Ordering Information” on page 2. In addition each device has a Flash memory signature row for calibration data, device identification, serial number etc. Non-volatile memory spaces can be locked for further write or read/write operations. This prevents unrestricted access to the application software. 8 8068E–AVR–08/08 XMEGA A3 7.3 In-System Programmable Flash Program Memory The XMEGA A3 devices contains On-chip In-System Programmable Flash memory for program storage, see Figure 7-1 on page 9. Since all AVR instructions are 16- or 32-bits wide, each Flash address location is 16 bits. The Program Flash memory space is divided into Application and Boot sections. Both sections have dedicated Lock Bits for setting restrictions on write or read/write operations. The Store Program Memory (SPM) instruction must reside in the Boot Section when used to write to the Flash memory. A third section inside the Application section is referred to as the Application Table section which has separate Lock bits for storage of write or read/write protection. The Application Table section can be used for storing non-volatile data or application software. Figure 7-1. Flash Program Memory (Hexadecimal address) Word Address 0 Application Section (256K/192K/128K/64K) ... 1EFFF 1F000 1FFFF 20000 20FFF / / / / / 16FFF 17000 17FFF 18000 18FFF / / / / / EFFF F000 FFFF 10000 10FFF / / / / / 77FF 7800 7FFF 8000 87FF Application Table Section (8K/8K/8K/4K) Boot Section (8K/8K/8K/4K) The Application Table Section and Boot Section can also be used for general application software. 9 8068E–AVR–08/08 XMEGA A3 7.4 Data Memory The Data Memory consist of the I/O Memory, EEPROM and SRAM memories, all within one linear address space, see Figure 7-2 on page 10. To simplify development, the memory map for all devices in the family is identical and with empty, reserved memory space for smaller devices. Figure 7-2. Data Memory Map (Hexadecimal address) ATxmega192A3 I/O Registers (4KB) EEPROM (4K) Byte Address 0 FFF 1000 17FF ATxmega128A3 I/O Registers (4KB) EEPROM (2K) RESERVED Byte Address 0 FFF 1000 Byte Address 0 FFF 1000 17FF ATxmega64A3 I/O Registers (4KB) EEPROM (2K) RESERVED 1FFF 2000 5FFF 6000 FFFFFF Internal SRAM (16K) External Memory (0 - 16 MB) 2000 3FFF 4000 FFFFFF Internal SRAM (8K) External Memory (0 - 16 MB) 2000 2FFF 3000 FFFFFF Internal SRAM (4K) External Memory (0 - 16 MB) Byte Address 0 FFF 1000 ATxmega256A3 I/O Registers (4KB) EEPROM (4K) 1FFF 2000 5FFF 6000 FFFFFF Internal SRAM (16K) External Memory (0 - 16 MB) 10 8068E–AVR–08/08 XMEGA A3 7.4.1 I/O Memory All peripherals and modules are addressable through I/O memory locations in the data memory space. All I/O memory locations can be accessed by the Load (LD/LDS/LDD) and Store (ST/STS/STD) instructions, transferring data between the 32 general purpose registers in the CPU and the I/O Memory. The IN and OUT instructions can address I/O memory locations in the range 0x00 - 0x3F directly. I/O registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. The value of single bits can be checked by using the SBIS and SBIC instructions on these registers. The I/O memory address for all peripherals and modules in XMEGA A3 is shown in the ”Peripheral Module Address Map” on page 53. 7.4.2 SRAM Data Memory The XMEGA A3 devices has internal SRAM memory for data storage. 7.4.3 EEPROM Data Memory The XMEGA A3 devices has internal EEPROM memory for non-volatile data storage. It is addressable either in a separate data space or it can be memory mapped into the normal data memory space. The EEPROM memory supports both byte and page access. 11 8068E–AVR–08/08 XMEGA A3 7.5 Calibration Row The Calibration Row is a separate memory section for factory programmed data. It contains calibration data for functions such as oscillators, device ID, and a factory programmed serial number that is unique for each device. The device ID for the available XMEGA A3 devices is shown in Table 7-1 on page 12. Some of the calibration values will be automatically loaded to the corresponding module or peripheral unit during reset. The Calibration Row can not be written or erased. It can be read from application software and external programming. Table 7-1. Device ID bytes for XMEGA A3 devices. Device Byte 2 ATxmega64A3 ATxmega128A3 ATxmega192A3 ATxmega256A3 42 42 44 42 Device ID bytes Byte 1 96 97 97 98 Byte 0 1E 1E 1E 1E 7.6 User Signature Row The User Signature Row is a separate memory section that is fully accessible (read and write) from application software and external programming. The User Signature Row is one flash page in size, and is meant for static user parameter storage, such as calibration data, custom serial numbers, random number seeds etc. This section is not erased by Chip Erase, and requires a dedicated erase command. This ensures parameter storage during multiple program/erase session and On-Chip Debug sessions. 12 8068E–AVR–08/08 XMEGA A3 7.7 Flash and EEPROM Page Size The Flash Program Memory and EEPROM data memory is organized in pages. The pages are word accessible for the Flash and byte accessible for the EEPROM. Table 7-2 on page 13 shows the Flash Program Memory organization. Flash write and erase operations are performed on one page at the time, while reading the Flash is done one byte at the time. For Flash access the Z-pointer (Z[m:n]) is used for addressing. The most significant bits in the address (FPAGE) gives the page number and the least significant address bits (FWORD) gives the word in the page. Table 7-2. Devices Flash Size (Bytes) ATxmega64A3 ATxmega128A3 ATxmega192A3 ATxmega256A3 64K + 4K 128K + 8K 192K + 8K 256K + 8K Page Size (words) 128 256 256 256 Number of words and Pages in the Flash. FWORD FPAGE Application Size Z[7:1] Z[8:1] Z[8:1] Z[8:1] Z[16:8] Z[17:9] Z[18:9] Z[18:9] 64K 128K 192K 256K No of Pages 256 256 384 512 Size 4K 8K 8K 8K Boot No of Pages 16 16 16 16 Table 7-3 on page 13 shows EEPROM memory organization for the XMEGA A3 devices. EEEPROM write and erase operations can be performed one page or one byte at the time, while reading the EEPROM is done one byte at the time. For EEPROM access the NVM Address Register (ADDR[m:n] is used for addressing. The most significant bits in the address (E2PAGE) gives the page number and the least significant address bits (E2BYTE) gives the byte in the page. Table 7-3. Devices EEPROM Size (Bytes) ATxmega64A3 ATxmega128A3 ATxmega192A3 ATxmega256A3 2K 2K 2K 4K Number of bytes and Pages in the EEPROM. Page Size (Bytes) 32 32 32 32 ADDR[4:0] ADDR[4:0] ADDR[4:0] ADDR[4:0] ADDR[10:5] ADDR[10:5] ADDR[10:5] ADDR[11:5] 64 64 64 128 E2BYTE E2PAGE No of Pages 13 8068E–AVR–08/08 XMEGA A3 8. DMAC - Direct Memory Access Controller 8.1 Features • Allows High-speed data transfer – From memory to peripheral – From memory to memory – From peripheral to memory – From peripheral to peripheral 4 Channels From 1 byte and up to 16 M bytes transfers in a single transaction Multiple addressing modes for source and destination address – Increment – Decrement – Static 1, 2, 4, or 8 bytes Burst Transfers Programmable priority between channels • • • • • 8.2 Overview The XMEGA A3 has a Direct Memory Access (DMA) Controller to move data between memories and peripherals in the data space. The DMA controller uses the same data bus as the CPU to transfer data. It has 4 channels that can be configured independently. Each DMA channel can perform data transfers in blocks of configurable size from 1 to 64K bytes. A repeat counter can be used to repeat each block transfer for single transactions up to 16M bytes. Each DMA channel can be configured to access the source and destination memory address with incrementing, decrementing or static addressing. The addressing is independent for source and destination address. When the transaction is complete the original source and destination address can automatically be reloaded to be ready for the next transaction. The DMAC can access all the peripherals through their I/O memory registers, and the DMA may be used for automatic transfer of data to/from communication modules, as well as automatic data retrieval from ADC conversions, data transfer to DAC conversions, or data transfer to or from port pins. A wide range of transfer triggers is available from the peripherals, Event System and software. Each DMA channel has different transfer triggers. To allow for continuous transfers, two channels can be interlinked so that the second takes over the transfer when the first is finished and vice versa. The DMA controller can read from memory mapped EEPROM, but it cannot write to the EEPROM or access the Flash. 14 8068E–AVR–08/08 XMEGA A3 9. Event System 9.1 Features • • • • Inter-peripheral communication and signalling with minimum latency CPU and DMA independent operation 8 Event Channels allows for up to 8 signals to be routed at the same time Events can be generated by – Timer/Counters (TCxn) – Real Time Counter (RTC) – Analog to Digital Converters (ADCx) – Analog Comparators (ACx) – Ports (PORTx) – System Clock (ClkSYS) – Software (CPU) Events can be used by – Timer/Counters (TCxn) – Analog to Digital Converters (ADCx) – Digital to Analog Converters (DACx) – Ports (PORTx) – DMA Controller (DMAC) – IR Communication Module (IRCOM) The same event can be used by multiple peripherals for synchronized timing Advanced Features – Manual Event Generation from software (CPU) – Quadrature Decoding – Digital Filtering Functions in Active and Idle mode • • • • 9.2 Overview The Event System is a set of features for inter-peripheral communication. It enables the possibility for a change of state in one peripheral to automatically trigger actions in one or more peripherals. What changes in a peripheral that will trigger actions in other peripherals are configurable by software. It is a simple, but powerful system as it allows for autonomous control of peripherals without any use of interrupts, CPU or DMA resources. The indication of a change in a peripheral is referred to as an event, and is usually the same as the interrupt conditions for that peripheral. Events are passed between peripherals using a dedicated routing network called the Event Routing Network. Figure 9-1 on page 16 shows a basic block diagram of the Event System with the Event Routing Network and the peripherals to which it is connected. This highly flexible system can be used for simple routing of signals, pin functions or for sequencing of events. The maximum latency is two CPU clock cycles from when an event is generated in one peripheral, until the actions are triggered in one or more other peripherals. The Event System is functional in both Active and Idle modes. 15 8068E–AVR–08/08 XMEGA A3 Figure 9-1. Event system block diagram. PORTx ClkSYS CPU ADCx Event Routing Network DACx RTC ACx IRCOM T/Cxn DMAC The Event Routing Network can directly connect together ADCs, DACs, Analog Comparators (ACx), I/O ports (PORTx), the Real-time Counter (RTC), Timer/Counters (T/C) and the IR Communication Module (IRCOM). Events can also be generated from software (CPU). All events from all peripherals are always routed into the Event Routing Network. This consist of eight multiplexers where each can be configured in software to select which event to be routed into that event channel. All eight event channels are connected to the peripherals that can use events, and each of these peripherals can be configured to use events from one or more event channels to automatically trigger a software selectable action. 16 8068E–AVR–08/08 XMEGA A3 10. System Clock and Clock options 10.1 Features • Fast start-up time • Safe run-time clock switching • Internal Oscillators: – 32 MHz run-time calibrated RC oscillator – 2 MHz run-time calibrated RC oscillator – 32 kHz calibrated RC oscillator – 32 kHz Ultra Low Power (ULP) oscillator External clock options – 0.4 - 16 MHz Crystal Oscillator – 32 kHz Crystal Oscillator – External clock PLL with internal and external clock options with 2 to 31x multiplication Clock Prescalers with 2 to 2048x division Fast peripheral clock running at 2 and 4 times the CPU clock speed Automatic Run-Time Calibration of internal oscillators Crystal Oscillator failure detection • • • • • • 10.2 Overview XMEGA A3 has an advanced clock system, supporting a large number of clock sources. It incorporates both integrated oscillators, external crystal oscillators and resonators. A high frequency Phase Locked Loop (PLL) and clock prescalers can be controlled from software to generate a wide range of clock frequencies from the clock source input. It is possible to switch between clock sources from software during run-time. After reset the device will always start up running from the 2 Mhz internal oscillator. A calibration feature is available, and can be used for automatic run-time calibration of the internal 2 MHz and 32 MHz oscillators. This reduce frequency drift over voltage and temperature. A Crystal Oscillator Failure Monitor can be enabled to issue a Non-Maskable Interrupt and switch to internal oscillator if the external oscillator fails. Figure 10-1 on page 18 shows the principal clock system in XMEGA A3. 17 8068E–AVR–08/08 XMEGA A3 Figure 10-1. Clock system overview clkULP 32 kHz ULP Internal Oscillator WDT/BOD clkRTC 32.768 kHz Calibrated Internal Oscillator 2 MHz Run-Time Calibrated Internal Oscillator 32 MHz Run-time Calibrated Internal Oscillator 32.768 KHz Crystal Oscillator RTC PERIPHERALS ADC DAC CLOCK CONTROL clkPER UNIT with PLL and Prescaler PORTS ... DMA INTERRUPT EVSYS RAM 0.4 - 16 MHz Crystal Oscillator CPU clkCPU NVM MEMORY External Clock Input FLASH EEPROM Each clock source is briefly described in the following sub-sections. 10.3 10.3.1 Clock Options 32 kHz Ultra Low Power Internal Oscillator The 32 kHz Ultra Low Power (ULP) Internal Oscillator is a very low power consumption clock source. It is used for the Watchdog Timer, Brown-Out Detection and as an asynchronous clock source for the Real Time Counter. This oscillator cannot be used as the system clock source, and it cannot be directly controlled from software. 10.3.2 32.768 kHz Calibrated Internal Oscillator The 32.768 kHz Calibrated Internal Oscillator is a high accuracy clock source that can be used as the system clock source or as an asynchronous clock source for the Real Time Counter. It is calibrated during protection to provide a default frequency which is close to its nominal frequency. 18 8068E–AVR–08/08 XMEGA A3 10.3.3 32.768 kHz Crystal Oscillator The 32.768 kHz Crystal Oscillator is a low power driver for an external watch crystal. It can be used as system clock source or as asynchronous clock source for the Real Time Counter. 10.3.4 0.4 - 16 MHz Crystal Oscillator The 0.4 - 16 MHz Crystal Oscillator is a driver intended for driving both external resonators and crystals ranging from 400 kHz to 16 MHz. 10.3.5 2 MHz Run-time Calibrated Internal Oscillator The 2 MHz Run-time Calibrated Internal Oscillator is a high frequency oscillator. It is calibrated during protection to provide a default frequency which is close to its nominal frequency. The oscillator can use the 32 kHz Calibrated Internal Oscillator or the 32 kHz Crystal Oscillator as a source for calibrating the frequency run-time to compensate for temperature and voltage drift hereby optimizing the accuracy of the oscillator. 10.3.6 32 MHz Run-time Calibrated Internal Oscillator The 32 MHz Run-time Calibrated Internal Oscillator is a high frequency oscillator. It is calibrated during protection to provide a default frequency which is close to its nominal frequency. The oscillator can use the 32 kHz Calibrated Internal Oscillator or the 32 kHz Crystal Oscillator as a source for calibrating the frequency run-time to compensate for temperature and voltage drift hereby optimizing the accuracy of the oscillator. 10.3.7 External Clock input The external clock input gives the possibility to connect a clock from an external source. 10.3.8 PLL with Multiplication factor 2 - 31x The PLL provides the possibility of multiplying a frequency by any number from 2 to 31. In combination with the prescalers, this gives a wide range of output frequencies from all clock sources. 19 8068E–AVR–08/08 XMEGA A3 11. Power Management and Sleep Modes 11.1 Features • 5 sleep modes – Idle – Power-down – Power-save – Standby – Extended standby • Power Reduction registers to disable clocks to unused peripherals 11.2 Overview The XMEGA A3 provides various sleep modes tailored to reduce power consumption to a minimum. All sleep modes are available and can be entered from Active mode. In Active mode the CPU is executing application code. The application code decides when and what sleep mode to enter. Interrupts from enabled peripherals and all enabled reset sources can restore the microcontroller from sleep to Active mode. In addition, Power Reduction registers provide a method to stop the clock to individual peripherals from software. When this is done, the current state of the peripheral is frozen and there is no power consumption from that peripheral. This reduces the power consumption in Active mode and Idle sleep mode. 11.3 11.3.1 Sleep Modes Idle Mode In Idle mode the CPU and Non-Volatile Memory are stopped, but all peripherals including the Interrupt Controller, Event System and DMA Controller are kept running. Interrupt requests from all enabled interrupts will wake the device. 11.3.2 Power-down Mode In Power-down mode all system clock sources, and the asynchronous Real Time Counter (RTC) clock source, are stopped. This allows operation of asynchronous modules only. The only interrupts that can wake up the MCU are the Two Wire Interface address match interrupts, and asynchronous port interrupts, e.g pin change. 11.3.3 Power-save Mode Power-save mode is identical to Power-down, with one exception: If the RTC is enabled, it will keep running during sleep and the device can also wake up from RTC interrupts. 11.3.4 Standby Mode Standby mode is identical to Power-down with the exception that all enabled system clock sources are kept running, while the CPU, Peripheral and RTC clocks are stopped. This reduces the wake-up time when external crystals or resonators are used. 20 8068E–AVR–08/08 XMEGA A3 11.3.5 Extended Standby Mode Extended Standby mode is identical to Power-save mode with the exception that all enabled system clock sources are kept running while the CPU and Peripheral clocks are stopped. This reduces the wake-up time when external crystals or resonators are used. 21 8068E–AVR–08/08 XMEGA A3 12. System Control and Reset 12.1 Features • Multiple reset sources for safe operation and device reset – Power-On Reset – External Reset – Watchdog Reset The Watchdog Timer runs from separate, dedicated oscillator – Brown-Out Reset Accurate, programmable Brown-Out levels – JTAG Reset – PDI reset – Software reset • Asynchronous reset – No running clock in the device is required for reset • Reset status register 12.2 Resetting the AVR During reset, all I/O registers are set to their initial values. The SRAM content is not reset. Application execution starts from the Reset Vector. The instruction placed at the Reset Vector should be an Absolute Jump (JMP) instruction to the reset handling routine. By default the Reset Vector address is the lowest Flash program memory address, ‘0’, but it is possible to move the Reset Vector to the first address in the Boot Section. The I/O ports of the AVR are immediately tri-stated when a reset source goes active. The reset functionality is asynchronous, so no running clock is required to reset the device. After the device is reset, the reset source can be determined by the application by reading the Reset Status Register. 12.3 12.3.1 Reset Sources Power-On Reset The MCU is reset when the supply voltage VCC is below the Power-on Reset threshold voltage. 12.3.2 External Reset The MCU is reset when a low level is present on the RESET pin. 12.3.3 Watchdog Reset The MCU is reset when the Watchdog Timer period expires and the Watchdog Reset is enabled. The Watchdog Timer runs from a dedicated oscillator independent of the System Clock. For more details see ”WDT - Watchdog Timer” on page 23. 12.3.4 Brown-Out Reset The MCU is reset when the supply voltage VCC is below the Brown-Out Reset threshold voltage and the Brown-out Detector is enabled. The Brown-out threshold voltage is programmable. 22 8068E–AVR–08/08 XMEGA A3 12.3.5 JTAG reset The MCU is reset as long as there is a logic one in the Reset Register in one of the scan chains of the JTAG system. Refer to IEEE 1149.1 (JTAG) Boundary-scan for details. 12.3.6 PDI reset The MCU can be reset through the Program and Debug Interface (PDI). 12.3.7 Software reset The MCU can be reset by the CPU writing to a special I/O register through a timed sequence. 12.4 12.4.1 WDT - Watchdog Timer Features • 11 selectable timeout periods, from 8 ms to 8s. • Two operation modes – Standard mode – Window mode • Runs from the 1 kHz output of the 32 kHz Ultra Low Power oscillator • Configuration lock to prevent unwanted changes 12.4.2 Overview The XMEGA A3 has a Watchdog Timer (WDT). The WDT will run continuously when turned on and if the Watchdog Timer is not reset within a software configurable time-out period, the microcontroller will be reset. The Watchdog Reset (WDR) instruction must be run by software to reset the WDT, and prevent microcontroller reset. The WDT has a Window mode. In this mode the WDR instruction must be run within a specified period called a window. Application software can set the minimum and maximum limits for this window. If the WDR instruction is not executed inside the window limits, the microcontroller will be reset. A protection mechanism using a timed write sequence is implemented in order to prevent unwanted enabling, disabling or change of WDT settings. For maximum safety, the WDT also has an Always-on mode. This mode is enabled by programming a fuse. In Always-on mode, application software can not disable the WDT. 23 8068E–AVR–08/08 XMEGA A3 13. PMIC - Programmable Multi-level Interrupt Controller 13.1 Features • Separate interrupt vector for each interrupt • Short, predictable interrupt response time • Programmable Multi-level Interrupt Controller – 3 programmable interrupt levels – Selectable priority scheme within low level interrupts (round-robin or fixed) – Non-Maskable Interrupts (NMI) • Interrupt vectors can be moved to the start of the Boot Section 13.2 Overview XMEGA A3 has a Programmable Multi-level Interrupt Controller (PMIC). All peripherals can define three different priority levels for interrupts; high, medium or low. Medium level interrupts may interrupt low level interrupt service routines. High level interrupts may interrupt both lowand medium level interrupt service routines. Low level interrupts have an optional round robin scheme to make sure all interrupts are serviced within a certain amount of time. The built in oscillator failure detection mechanism can issue a Non-Maskable Interrupt (NMI). 13.3 Interrupt vectors When an interrupt is serviced, the program counter will jump to the interrupt vector address. The interrupt vector is the sum of the peripheral’s base interrupt address and the offset address for specific interrupts in each peripheral. The base addresses for the XMEGA A3 devices are shown in Table 13-1. Offset addresses for each interrupt available in the peripheral are described for each peripheral in the XMEGA A manual. For peripherals or modules that have only one interrupt, the interrupt vector is shown in Table 13-1. The program address is the word address. Table 13-1. Reset and Interrupt Vectors Source RESET OSCF_INT_vect PORTC_INT_base PORTR_INT_base DMAC_INT_base RTC_INT_base TWIC_INT_base TIMERC0_INT_base TIMERC1_INT_base SPIC_INT_vect USARTC0_INT_base USARTC1_INT_base AES_INT_vect Crystal Oscillator Failure Interrupt vector (NMI) Port C Interrupt base Port R Interrupt base DMA Controller Interrupt base Real Time Counter Interrupt base Two-Wire Interface on Port C Interrupt base Timer/Counter 0 on port C Interrupt base Timer/Counter 1 on port C Interrupt base SPI on port C Interrupt vector USART 0 on port C Interrupt base USART 1 on port C Interrupt base AES Interrupt vector Interrupt Description Program Address (Base Address) 0x000 0x002 0x004 0x008 0x00C 0x014 0x018 0x01C 0x028 0x030 0x032 0x03D 0x03E 24 8068E–AVR–08/08 XMEGA A3 Table 13-1. Reset and Interrupt Vectors (Continued) Source NVM_INT_base PORTB_INT_base ACB_INT_base ADCB_INT_base PORTE_INT_base TWIE_INT_base TIMERE0_INT_base TIMERE1_INT_base SPIE_INT_vect USARTE0_INT_base USARTE1_INT_base PORTD_INT_base PORTA_INT_base ACA_INT_base ADCA_INT_base TIMERD0_INT_base TIMERD1_INT_base SPID_INT_vector USARTD0_INT_base USARTD1_INT_base PORTF_INT_base TIMERF0_INT_base USARTF0_INT_base Interrupt Description Non-Volatile Memory Interrupt base Port B Interrupt base Analog Comparator on Port B Interrupt base Analog to Digital Converter on Port B Interrupt base Port E INT base Two-Wire Interface on Port E Interrupt base Timer/Counter 0 on port E Interrupt base Timer/Counter 1 on port E Interrupt base SPI on port E Interrupt vector USART 0 on port E Interrupt base USART 1 on port E Interrupt base Port D Interrupt base Port A Interrupt base Analog Comparator on Port A Interrupt base Analog to Digital Converter on Port A Interrupt base Timer/Counter 0 on port D Interrupt base Timer/Counter 1 on port D Interrupt base SPI D Interrupt vector USART 0 on port D Interrupt base USART 1 on port D Interrupt base Port F Interrupt base Timer/Counter 0 on port F Interrupt base USART 0 on port F Interrupt base Program Address (Base Address) 0x040 0x044 0x048 0x04E 0x056 0x05A 0x05E 0x06A 0x072 0x074 0x07A 0x080 0x084 0x088 0x08E 0x09A 0x0A6 0x0AE 0x0B0 0x0B6 0x0D0 0x0D8 0x0EE 25 8068E–AVR–08/08 XMEGA A3 14. I/O Ports 14.1 Features • Selectable input and output configuration for each pin individually • Flexible pin configuration through dedicated Pin Configuration Register • Synchronous and/or asynchronous input sensing with port interrupts and events – Sense both edges – Sense rising edges – Sense falling edges – Sense low level Asynchronous wake-up from all input sensing configurations Two port interrupts with flexible pin masking Highly configurable output driver and pull settings: – Totem-pole – Pull-up/-down – Wired-AND – Wired-OR – Bus-keeper – Inverted I/O Optional Slew rate control Configuration of multiple pins in a single operation Read-Modify-Write (RMW) support Toggle/clear/set registers for Output and Direction registers Clock output on port pin Event Channel 7 output on port pin Mapping of port registers (virtual ports) into bit accessible I/O memory space • • • • • • • • • • 14.2 Overview The XMEGA A3 devices have flexible General Purpose I/O Ports. A port consists of up to 8 pins, ranging from pin 0 to pin 7. The ports implement several functions, including synchronous/asynchronous input sensing, pin change interrupts and configurable output settings. All functions are individual per pin, but several pins may be configured in a single operation. 14.3 I/O configuration All port pins (Pn) have programmable output configuration. In addition, all port pins have an inverted I/O function. For an input, this means inverting the signal between the port pin and the pin register. For an output, this means inverting the output signal between the port register and the port pin. The inverted I/O function can be used also when the pin is used for alternate functions. The port pins also have configurable slew rate limitation to reduce electromagnetic emission. 26 8068E–AVR–08/08 XMEGA A3 14.3.1 Push-pull Figure 14-1. I/O configuration - Totem-pole DIRn OUTn INn Pn 14.3.2 Pull-down Figure 14-2. I/O configuration - Totem-pole with pull-down (on input) DIRn OUTn INn Pn 14.3.3 Pull-up Figure 14-3. I/O configuration - Totem-pole with pull-up (on input) DIRn OUTn INn 14.3.4 Bus-keeper Pn The bus-keeper’s weak output produces the same logical level as the last output level. It acts as a pull-up if the last level was ‘1’, and pull-down if the last level was ‘0’. 27 8068E–AVR–08/08 XMEGA A3 Figure 14-4. I/O configuration - Totem-pole with bus-keeper DIRn OUTn INn Pn 14.3.5 Others Figure 14-5. Output configuration - Wired-OR with optional pull-down OUTn Pn INn Figure 14-6. I/O configuration - Wired-AND with optional pull-up INn Pn OUTn 28 8068E–AVR–08/08 XMEGA A3 14.4 Input sensing • • • • Sense both edges Sense rising edges Sense falling edges Sense low level Input sensing is synchronous or asynchronous depending on the enabled clock for the ports, and the configuration is shown in Figure 14-7 on page 29. Figure 14-7. Input sensing system overview Asynchronous sensing EDGE DETECT Interrupt Control IREQ Synchronous sensing Pn Synchronizer INn D QD Q EDGE DETECT Event INVERTED I/O R R When a pin is configured with inverted I/O the pin value is inverted before the input sensing. 14.5 Port Interrupt Each ports have two interrupts with separate priority and interrupt vector. All pins on the port can be individually selected as source for each of the interrupts. The interrupts are then triggered according to the input sense configuration for each pin configured as source for the interrupt. 14.6 Alternate Port Functions In addition to the input/output functions on all port pins, most pins have alternate functions. This means that other modules or peripherals connected to the port can use the port pins for their functions, such as communication or pulse-width modulation. ”Pinout and Pin Functions” on page 48 shows which modules on peripherals that enables alternate functions on a pin, and what alternate functions that is available on a pin. 29 8068E–AVR–08/08 XMEGA A3 15. T/C - 16-bits Timer/Counter with PWM 15.1 Features • Seven 16-bit Timer/Counters – Four Timer/Counters of type 0 – Three Timer/Counters of type 1 Four Compare or Capture (CC) Channels in Timer/Counter 0 Two Compare or Capture (CC) Channels in Timer/Counter 1 Double Buffered Timer Period Setting Double Buffered Compare or Capture Channels Waveform Generation: – Single Slope Pulse Width Modulation – Dual Slope Pulse Width Modulation – Frequency Generation Input Capture: – Input Capture with Noise Cancelling – Frequency capture – Pulse width capture – 32-bit input capture Event Counter with Direction Control Timer Overflow and Timer Error Interrupts and Events One Compare Match or Capture Interrupt and Event per CC Channel Supports DMA Operation Hi-Resolution Extension (Hi-Res) Advanced Waveform Extension (AWEX) • • • • • • • • • • • • 15.2 Overview XMEGA A3 has seven Timer/Counters, four Timer/Counter 0 and three Timer/Counter 1. The difference between them is that Timer/Counter 0 has four Compare/Capture channels, while Timer/Counter 1 has two Compare/Capture channels. The Timer/Counters (T/C) are 16-bit and can count any clock, event or external input in the microcontroller. A programmable prescaler is available to get a useful T/C resolution. Updates of Timer and Compare registers are double buffered to ensure glitch free operation. Single slope PWM, dual slope PWM and frequency generation waveforms can be generated using the Compare Channels. Through the Event System, any input pin or event in the microcontroller can be used to trigger input capture, hence no dedicated pins is required for this. The input capture has a noise canceller to avoid incorrect capture of the T/C, and can be used to do frequency and pulse width measurements. A wide range of interrupt or event sources are available, including T/C Overflow, Compare match and Capture for each Compare/Capture channel in the T/C. PORTC, PORTD and PORTE each has one Timer/Counter 0 and one Timer/Counter1. PORTF has one Timer/Counter 0. Notation of these are TCC0 (Time/Counter C0), TCC1, TCD0, TCD1, TCE0, TCE1 and TCF0, respectively. 30 8068E–AVR–08/08 XMEGA A3 Figure 15-1. Overview of a Timer/Counter and closely related peripherals Timer/Counter Base Counter Timer Period Counter Control Logic Prescaler Event System clkPER clkPER4 Compare/Capture Channel D Compare/Capture Channel C Compare/Capture Channel B Compare/Capture Channel A Comparator Buffer Capture Control Waveform Generation AWeX Hi-Res DTI Dead-Time Insertion Pattern Generation Fault Protection The Hi-Resolution Extension can be enabled to increase the waveform generation resolution by 2 bits (4x). This is available for all Timer/Counters. See ”Hi-Res - High Resolution Extension” on page 33 for more details. The Advanced Waveform Extension can be enabled to provide extra and more advanced features for the Timer/Counter. This are only available for Timer/Counter 0. See ”AWEX - Advanced Waveform Extension” on page 32 for more details. PORT 31 8068E–AVR–08/08 XMEGA A3 16. AWEX - Advanced Waveform Extension 16.1 Features • • • • • • • • Output with complementary output from each Capture channel Four Dead Time Insertion (DTI) Units, one for each Capture channel 8-bit DTI Resolution Separate High and Low Side Dead-Time Setting Double Buffered Dead-Time Event Controlled Fault Protection Single Channel Multiple Output Operation (for BLDC motor control) Double Buffered Pattern Generation 16.2 Overview The Advanced Waveform Extension (AWEX) provides extra features to the Timer/Counter in Waveform Generation (WG) modes. The AWEX enables easy and safe implementation of for example, advanced motor control (AC, BLDC, SR, and Stepper) and power control applications. Any WG output from a Timer/Counter 0 is split into a complimentary pair of outputs when any AWEX feature is enabled. These output pairs go through a Dead-Time Insertion (DTI) unit that enables generation of the non-inverted Low Side (LS) and inverted High Side (HS) of the WG output with dead time insertion between LS and HS switching. The DTI output will override the normal port value according to the port override setting. Optionally the final output can be inverted by using the invert I/O setting for the port pin. The Pattern Generation unit can be used to generate a synchronized bit pattern on the port it is connected to. In addition, the waveform generator output from Compare Channel A can be distributed to, and override all port pins. When the Pattern Generator unit is enabled, the DTI unit is bypassed. The Fault Protection unit is connected to the Event System. This enables any event to trigger a fault condition that will disable the AWEX output. Several event channels can be used to trigger fault on several different conditions. The AWEX is available for TCC0. The notation of this is AWEXC. 32 8068E–AVR–08/08 XMEGA A3 17. Hi-Res - High Resolution Extension 17.1 Features • Increases Waveform Generator resolution by 2-bits (4x) • Supports Frequency, single- and dual-slope PWM operation • Supports the AWEX when this is enabled and used for the same Timer/Counter 17.2 Overview The Hi-Resolution (Hi-Res) Extension is able to increase the resolution of the waveform generation output by a factor of 4. When enabled for a Timer/Counter, the Fast Peripheral clock running at four times the CPU clock speed will be as input to the Timer/Counter. The High Resolution Extension can also be used when an AWEX is enabled and used with a Timer/Counter. XMEGA A3 devices have four Hi-Res Extensions that each can be enabled for each Timer/Counters pair on PORTC, PORTD, PORTE and PORTF. The notation of these are HIRESC, HIRESD, HIRESE and HIRESF, respectively. 33 8068E–AVR–08/08 XMEGA A3 18. RTC - Real-Time Counter 18.1 Features • • • • • • 16-bit Timer Flexible Tick resolution ranging from 1 Hz to 32.768 kHz One Compare register One Period register Clear timer on Overflow or Compare Match Overflow or Compare Match event and interrupt generation 18.2 Overview The XMEGA A3 includes a 16-bit Real-time Counter (RTC). The RTC can be clocked from an accurate 32.768 kHz Crystal Oscillator, the 32.768 kHz Calibrated Internal Oscillator, or from the 32 kHz Ultra Low Power Internal Oscillator. The RTC includes both a Period and a Compare register. For details, see Figure 18-1. A wide range of Resolution and Time-out periods can be configured using the RTC. With a maximum resolution of 30.5 µs, time-out periods range up to 2000 seconds. With a resolution of 1 second, the maximum time-out period is over 18 hours (65536 seconds). Figure 18-1. Real-time Counter overview Period 32 kHz 10-bit prescaler 1 kHz = = Overflow Counter Compare Match Compare 34 8068E–AVR–08/08 XMEGA A3 19. TWI - Two Wire Interface 19.1 Features • • • • • • • • • • • • Two Identical TWI peripherals Simple yet Powerful and Flexible Communication Interface Both Master and Slave Operation Supported Device can Operate as Transmitter or Receiver 7-bit Address Space Allows up to 128 Different Slave Addresses Multi-master Arbitration Support Up to 400 kHz Data Transfer Speed Slew-rate Limited Output Drivers Noise Suppression Circuitry Rejects Spikes on Bus Lines Fully Programmable Slave Address with General Call Support Address Recognition Causes Wake-up when in Sleep Mode I2C and System Management Bus (SMBus) compatible 19.2 Overview The Two-Wire Interface (TWI) is a bi-directional wired-AND bus with only two lines, the clock (SCL) line and the data (SDA) line. The protocol makes it possible to interconnect up to 128 individually addressable devices. Since it is a multi-master bus, one or more devices capable of taking control of the bus can be connected. The only external hardware needed to implement the bus is a single pull-up resistor for each of the TWI bus lines. Mechanisms for resolving bus contention are inherent in the TWI protocol. PORTC and PORTE each has one TWI. Notation of these peripherals are TWIC and TWIE. 35 8068E–AVR–08/08 XMEGA A3 20. SPI - Serial Peripheral Interface 20.1 Features • • • • • • • • • Three Identical SPI peripherals Full-duplex, Three-wire Synchronous Data Transfer Master or Slave Operation LSB First or MSB First Data Transfer Seven Programmable Bit Rates End of Transmission Interrupt Flag Write Collision Flag Protection Wake-up from Idle Mode Double Speed (CK/2) Master SPI Mode 20.2 Overview The Serial Peripheral Interface (SPI) allows high-speed full-duplex, synchronous data transfer between different devices. Devices can communicate using a master-slave scheme, and data is transferred both to and from the devices simultaneously. PORTC, PORTD, and PORTE each has one SPI. Notation of these peripherals are SPIC, SPID, and SPIE respectively. 36 8068E–AVR–08/08 XMEGA A3 21. USART 21.1 Features • • • • • • • • • • • • • • • Seven Identical USART peripherals Full Duplex Operation (Independent Serial Receive and Transmit Registers) Asynchronous or Synchronous Operation Master or Slave Clocked Synchronous Operation High-resolution Arithmetic Baud Rate Generator Supports Serial Frames with 5, 6, 7, 8, or 9 Data Bits and 1 or 2 Stop Bits Odd or Even Parity Generation and Parity Check Supported by Hardware Data OverRun Detection Framing Error Detection Noise Filtering Includes False Start Bit Detection and Digital Low Pass Filter Three Separate Interrupts on TX Complete, TX Data Register Empty and RX Complete Multi-processor Communication Mode Double Speed Asynchronous Communication Mode Master SPI mode for SPI communication IrDA support through the IRCOM module 21.2 Overview The Universal Synchronous and Asynchronous serial Receiver and Transmitter (USART) is a highly flexible serial communication module. The USART supports full duplex communication, and both asynchronous and clocked synchronous operation. The USART can also be set in Master SPI mode to be used for SPI communication. Communication is frame based, and the frame format can be customized to support a wide range of standards. The USART is buffered in both direction, enabling continued data transmission without any delay between frames. There are separate interrupt vectors for receive and transmit complete, enabling fully interrupt driven communication. Frame error and buffer overflow are detected in hardware and indicated with separate status flags. Even or odd parity generation and parity check can also be enabled. One USART can use the IRCOM module to support IrDA 1.4 physical compliant pulse modulation and demodulation for baud rates up to 115.2 kbps. PORTC, PORTD, and PORTE each has two USARTs, while PORTF has one USART only. Notation of these peripherals are USARTC0, USARTC1, USARTD0, USARTD1, USARTE0, USARTE1 and USARTF0, respectively. 37 8068E–AVR–08/08 XMEGA A3 22. IRCOM - IR Communication Module 22.1 Features • Pulse modulation/demodulation for infrared communication • Compatible to IrDA 1.4 physical for baud rates up to 115.2 kbps • Selectable pulse modulation scheme – 3/16 of baud rate period – Fixed pulse period, 8-bit programmable – Pulse modulation disabled • Built in filtering • Can be connected to and used by one USART at the time 22.2 Overview XMEGA contains an Infrared Communication Module (IRCOM) for IrDA communication with baud rates up to 115.2 kbps. This supports three modulation schemes: 3/16 of baud rate period, fixed programmable pulse time based on the Peripheral Clock speed, or pulse modulation disabled. There is one IRCOM available which can be connected to any USART to enable infrared pulse coding/decoding for that USART. 38 8068E–AVR–08/08 XMEGA A3 23. Crypto Engine 23.1 Features • Data Encryption Standard (DES) CPU instruction • Advanced Encryption Standard (AES) Crypto module • DES Instruction – Encryption and Decryption – Single-cycle DES instruction – Encryption/Decryption in 16 clock cycles per 8-byte block • AES Crypto Module – Encryption and Decryption – Support 128-bit keys – Support XOR data load mode to the State memory for Cipher Block Chaining – Encryption/Decryption in 375 clock cycles per 16-byte block 23.2 Overview The Advanced Encryption Standard (AES) and Data Encryption Standard (DES) are two commonly used encryption standards. These are supported through an AES peripheral module and a DES CPU instruction. All communication interfaces and the CPU can optionally use AES and DES encrypted communication and data storage. DES is supported by a DES instruction in the AVR XMEGA CPU. The 8-byte key and 8-byte data blocks must be loaded into the Register file, and then DES must be executed 16 times to encrypt/decrypt the data block. The AES Crypto Module encrypts and decrypts 128-bit data blocks with the use of a 128-bit key. The key and data must be loaded into the key and state memory in the module before encryption/decryption is started. It takes 375 peripheral clock cycles before the encryption/decryption is done and decrypted/encrypted data can be read out, and an optional interrupt can be generated. The AES Crypto Module also has DMA support with transfer triggers when encryption/decryption is done and optional auto-start of encryption/decryption when the state memory is fully loaded. 39 8068E–AVR–08/08 XMEGA A3 24. ADC - 12-bit Analog to Digital Converter 24.1 Features • • • • • • • • • • • • Two ADCs with 12-bit resolution 2 Msps sample rate for each ADC Signed and Unsigned conversions 4 result registers with individual input channel control for each ADC 8 single ended inputs for each ADC 8x4 differential inputs for each ADC Software selectable gain of 2, 4, 8, 16, 32 or 64 Software selectable resolution of 8- or 12-bit. Internal or External Reference selection Event triggered conversion for accurate timing DMA transfer of conversion results Interrupt/Event on compare result 24.2 Overview XMEGA A3 devices have two Analog to Digital Converters (ADC), see Figure 24-1 on page 41. The two ADC modules can be operated simultaneously, individually or synchronized. The ADC converts analog voltages to digital values. The ADC has 12-bit resolution and is capable of converting up to 2 million samples per second. The input selection is flexible, and both single-ended and differential measurements can be performed. The ADC can provide both signed and unsigned results, and an optional gain stage is available to increase the dynamic range of the ADC. It is a Successive Approximation Result (SAR) ADC. A SAR ADC measures one bit of the conversion result at a time. The ADC has a pipeline architecture. This means that a new analog voltage can be sampled and a new ADC measurement started on each ADC clock cycle. Each sample will be converted in the pipeline, where the total sample and conversion time is seven ADC clock cycles for 12-bit result and 5 ADC clock cycles for 8-bit result. ADC measurements can be started by application software or an incoming event from another peripheral in the device. Four different result registers with individual channel selection (MUX registers) are provided to make it easier for the application to keep track of the data. It is also possible to use DMA to move ADC results directly to memory or peripherals. Both internal and external analog reference voltages can be used. An accurate internal 1.0V reference is available. 40 8068E–AVR–08/08 XMEGA A3 Figure 24-1. ADC overview Channel A MUX selection Channel B MUX selection Channel C MUX selection Internal inputs Channel D MUX selection Configuration Reference selection Channel A Register Channel B Register Pin inputs ADC Channel C Register Channel D Register Pin inputs 1-64 X Event Trigger Each ADC has four MUX selection registers with a corresponding result register. This means that four channels can be sampled within 1.5 µs without any intervention by the application other than starting the conversion. The results will be available in the result registers. The ADC may be configured for 8- or 12-bit result, reducing the minimum conversion time (propagation delay) from 3.5 µs for 12-bit to 2.5 µs for 8-bit result. ADC conversion results are provided left- or right adjusted with optional ‘1’ or ‘0’ padding. This eases calculation when the result is represented as a signed integer (signed 16-bit number). PORTA and PORTB each has one ADC. Notation of these peripherals are ADCA and ADCB, respectively. 41 8068E–AVR–08/08 XMEGA A3 25. DAC - 12-bit Digital to Analog Converter 25.1 Features • • • • • • • • One DAC with 12-bit resolution Up to 1 Msps conversion rate for each DAC Flexible conversion range Multiple trigger sources 1 continuous output or 2 Sample and Hold (S/H) outputs for each DAC Built-in offset and gain calibration High drive capabilities Low Power Mode 25.2 Overview The XMEGA A3 devices features two 12-bit, 1 Msps DACs with built-in offset and gain calibration, see Figure 25-1 on page 42. A DAC converts a digital value into an analog signal. The DAC may use an internal 1.1 voltage as the upper limit for conversion, but it is also possible to use the supply voltage or any applied voltage in-between. The external reference input is shared with the ADC reference input. Figure 25-1. DAC overview Configuration Reference selection Channel A Register Channel A DAC Channel B Register Channel B Event Trigger Each DAC has one continuous output with high drive capabilities for both resistive and capacitive loads. It is also possible to split the continuous time channel into two Sample and Hold (S/H) channels, each with separate data conversion registers. A DAC conversion may be started from the application software by writing the data conversion registers. The DAC can also be configured to do conversions triggered by the Event System to have regular timing, independent of the application software. DMA may be used for transferring data from memory locations to DAC data registers. The DAC has a built-in calibration system to reduce offset and gain error when loading with a calibration value from software. PORTB each has one DAC. Notation of this peripheral is DACB. 42 8068E–AVR–08/08 XMEGA A3 26. AC - Analog Comparator 26.1 Features • Four Analog Comparators • Selectable Power vs. Speed • Selectable hysteresis – 0, 20 mV, 50 mV • Analog Comparator output available on pin • Flexible Input Selection – All pins on the port – Output from the DAC – Bandgap reference voltage. – Voltage scaler that can perform a 64-level scaling of the internal VCC voltage. • Interrupt and event generation on – Rising edge – Falling edge – Toggle • Window function interrupt and event generation on – Signal above window – Signal inside window – Signal below window 26.2 Overview XMEGA A3 features four Analog Comparators (AC). An Analog Comparator compares two voltages, and the output indicates which input is largest. The Analog Comparator may be configured to give interrupt requests and/or events upon several different combinations of input change. Both hysteresis and propagation delays may be adjusted in order to find the optimal operation for each application. A wide range of input selection is available, both external pins and several internal signals can be used. The Analog Comparators are always grouped in pairs (AC0 and AC1) on each analog port. They have identical behavior but separate control registers. Optionally, the state of the comparator is directly available on a pin. PORTA and PORTB each has one AC pair. Notations are ACA and ACB, respectively. 43 8068E–AVR–08/08 XMEGA A3 Figure 26-1. Analog comparator overview Pin inputs Internal inputs + AC0 Pin inputs Internal inputs VCC scaled Interrupt sensitivity control Interrupts Events Pin 0 output Pin inputs Internal inputs + AC1 Pin inputs Internal inputs VCC scaled - 44 8068E–AVR–08/08 XMEGA A3 26.3 Input Selection The Analog comparators have a very flexible input selection and the two comparators grouped in a pair may be used to realize a window function. One pair of analog comparators is shown in Figure 26-1 on page 44. • Input selection from pin – Pin 0, 1, 2, 3, 4, 5, 6 selectable to positive input of analog comparator – Pin 0, 1, 3, 5, 7 selectable to negative input of analog comparator • Internal signals available on positive analog comparator inputs – Output from 12-bit DAC • Internal signals available on negative analog comparator inputs – 64-level scaler of the VCC, available on negative analog comparator input – Bandgap voltage reference • Output from 12-bit DAC 26.4 Window Function The window function is realized by connecting the external inputs of the two analog comparators in a pair as shown in Figure 26-2. Figure 26-2. Analog comparator window function + AC0 Upper limit of window Input signal Interrupt sensitivity control + AC1 Lower limit of window Interrupts Events 45 8068E–AVR–08/08 XMEGA A3 27. OCD - On-chip Debug 27.1 Features • Complete Program Flow Control – Go, Stop, Reset, Step into, Step over, Step out, Run-to-Cursor Debugging on C and high-level language source code level Debugging on Assembler and disassembler level 1 dedicated program address or source level breakpoint for AVR Studio / debugger 4 Hardware Breakpoints Unlimited Number of User Program Breakpoints Unlimited Number of User Data Breakpoints, with break on: – Data location read, write or both read and write – Data location content equal or not equal to a value – Data location content is greater or less than a value – Data location content is within or outside a range – Bits of a data location are equal or not equal to a value • Non-Intrusive Operation – No hardware or software resources in the device are used • High Speed Operation – No limitation on debug/programming clock frequency versus system clock frequency • • • • • • 27.2 Overview The XMEGA A3 has a powerful On-Chip Debug (OCD) system that - in combination with Atmel’s development tools - provides all the necessary functions to debug an application. It has support for program and data breakpoints, and can debug an application from C and high level language source code level, as well as assembler and disassembler level. It has full Non-Intrusive Operation and no hardware or software resources in the device are used. The ODC system is accessed through an external debugging tool which connects to the JTAG or PDI physical interfaces. Refer to ”Program and Debug Interfaces” on page 47. 46 8068E–AVR–08/08 XMEGA A3 28. Program and Debug Interfaces 28.1 Features • • • • • PDI - Program and Debug Interface (Atmel proprietary 2-pin interface) JTAG Interface (IEEE std. 1149.1 compliant) Boundary-scan capabilities according to the IEEE Std. 1149.1 (JTAG) Access to the OCD system Programming of Flash, EEPROM, Fuses and Lock Bits 28.2 Overview The programming and debug facilities are accessed through the JTAG and PDI physical interfaces. The PDI physical uses one dedicated pin together with the Reset pin, and no general purpose pins are used. JTAG uses four general purpose pins on PORTB. 28.3 JTAG interface The JTAG physical layer handles the basic low-level serial communication over four I/O lines named TMS, TCK, TDI, and TDO. It complies to the IEEE Std. 1149.1 for test access port and boundary scan. 28.4 PDI - Program and Debug Interface The PDI is an Atmel proprietary protocol for communication between the microcontroller and Atmel’s development tools. 47 8068E–AVR–08/08 XMEGA A3 29. Pinout and Pin Functions The pinout of XMEGA A3 is shown in ”For packaging information, see ”Packaging information” on page 66.” on page 2. In addition to general I/O functionality, each pin may have several function. This will depend on which peripheral is enabled and connected to the actual pin. Only one of the alternate pin functions can be used at time. 29.1 29.1.1 Alternate Pin Function Description The tables below show the notation for all pin functions available and describe its function. Operation/Power Supply VCC AVCC GND Digital supply voltage Analog supply voltage Ground 29.1.2 Port Interrupt functions SYNC ASYNC Port pin with full synchronous and limited asynchronous interrupt function Port pin with full synchronous and full asynchronous interrupt function 29.1.3 Analog functions ACn AC0OUT ADCn DACn AREF Analog Comparator input pin n Analog Comparator 0 Output Analog to Digital Converter input pin n Digital to Analog Converter output pin n Analog Reference input pin 48 8068E–AVR–08/08 XMEGA A3 29.1.4 Timer/Counter and AWEX functions OCnx OCxn Output Compare Channel x for Timer/Counter n Inverted Output Compare Channel x for Timer/Counter n 29.1.5 Communication functions SCL SDA SCLIN SCLOUT SDAIN SDAOUT XCKn RXDn TXDn SS MOSI MISO SCK Serial Clock for TWI Serial Data for TWI Serial Clock In for TWI when external driver interface is enabled Serial Clock Out for TWI when external driver interface is enabled Serial Data In for TWI when external driver interface is enabled Serial Data Out for TWI when external driver interface is enabled Transfer Clock for USART n Receiver Data for USART n Transmitter Data for USART n Slave Select for SPI Master Out Slave In for SPI Master In Slave Out for SPI Serial Clock for SPI 29.1.6 Oscillators, Clock and Event TOSCn XTALn CLKOUT EVOUT Timer Oscillator pin n Input/Output for inverting Oscillator pin n Peripheral Clock Output Event Channel 0 Output 29.1.7 Debug/System functions RESET PDI_CLK PDI_DATA TCK TDI TDO TMS Reset pin Program and Debug Interface Clock pin Program and Debug Interface Data pin JTAG Test Clock JTAG Test Data In JTAG Test Data Out JTAG Test Mode Select 49 8068E–AVR–08/08 XMEGA A3 29.2 Alternate Pin Functions The tables below show the main and alternate pin functions for all pins on each port. They also show which peripheral that makes use of or enables the alternate pin function. Table 29-1. PORT A GND AVCC PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PIN # 60 61 62 63 64 1 2 3 4 5 Port A - Alternate functions INTERRUPT ADCA POS ADCA NEG ADAA GAINPOS ADCA GAINNEG ACA POS ACA NEG ACA OUT REFA SYNC SYNC SYNC/ASYNC SYNC SYNC SYNC SYNC SYNC ADC0 ADC1 ADC2 ADC3 ADC4 ADC5 ADC6 ADC7 ADC0 ADC1 ADC2 ADC3 ADC0 ADC1 ADC2 ADC3 ADC4 ADC5 ADC6 ADC7 ADC4 ADC5 ADC6 ADC7 AC0 AC1 AC2 AC3 AC4 AC5 AC6 AC0 AC1 AREFA AC3 AC5 AC7 AC0 OUT Table 29-2. PORT B PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 GND VCC PIN # 6 6 8 9 10 11 12 13 14 15 Port B - Alternate functions INTERRUPT SYNC SYNC SYNC/ASYNC SYNC SYNC SYNC SYNC SYNC ADCB POS ADC0 ADC1 ADC2 ADC3 ADC4 ADC5 ADC6 ADC7 ADCB NEG ADC0 ADC1 ADC2 ADC3 ADCB GAINPOS ADC0 ADC1 ADC2 ADC3 ADC4 ADC5 ADC6 ADC7 ADC4 ADC5 ADC6 ADC7 ADCB GAINNEG ACB POS AC0 AC1 AC2 AC3 AC4 AC5 AC6 AC7 AC0 OUT AC5 AC3 ACB NEG AC0 AC1 DAC0 DAC1 TMS TDI TCK TDO ACB OUT DACB REFB AREFB JTAG 50 8068E–AVR–08/08 XMEGA A3 Table 29-3. PORT C PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 GND VCC PIN # 16 17 18 19 20 21 22 23 24 25 Port C - Alternate functions INTERRUPT SYNC SYNC SYNC/ASYNC SYNC SYNC SYNC SYNC SYNC TCC0 OC0A OC0B OC0C OC0D AWEXC OC0A OC0A OC0B OC0B OC0C OC0C OC0D OC0D OC1A OC1B XCK1 RXD1 TXD1 XCK0 RXD0 TXD0 SS MOSI MISO SCK CLKOUT EVOUT TCC1 USARTC0 USARTC1 SPIC TWIC SDA SCL CLOCKOUT EVENTOUT Table 29-4. PORT D PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 GND VCC PIN # 26 27 28 29 30 31 32 33 34 35 Port D - Alternate functions INTERRUPT SYNC SYNC SYNC/ASYNC SYNC SYNC SYNC SYNC SYNC TCD0 OC0A OC0B OC0C OC0D OC1A OC1B XCK1 RXD1 TXD1 XCK0 RXD0 TXD0 SS MOSI MISO SCK CLKOUT EVOUT TCD1 USARTD0 USARTD1 SPID CLOCKOUT EVENTOUT Table 29-5. PORT E PE0 PE1 PE2 PE3 PE4 PE5 PE6 PE7 GND VCC PIN # 36 37 38 39 40 41 42 43 44 45 Port E - Alternate functions INTERRUPT SYNC SYNC SYNC/ASYNC SYNC SYNC SYNC SYNC SYNC TCE0 OC0A OC0B OC0C OC0D OC1A OC1B XCK1 RXD1 TXD1 XCK0 RXD0 TXD0 SS MOSI MISO SCK CLKOUT EVOUT TOSC1 TOSC1 TCE1 USARTE0 USARTE1 SPIE TWIE SDA SCL CLOCKOUT EVENTOUT TOSC 51 8068E–AVR–08/08 XMEGA A3 Table 29-6. PORT F PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 GND VCC Port F - Alternate functions PIN # 46 47 48 49 50 51 54 55 52 53 INTERRUPT SYNC SYNC SYNC/ASYNC SYNC SYNC SYNC SYNC SYNC TCF0 OC0A OC0B OC0C OC0D XCK0 RXD0 TXD0 USARTF0 Table 29-7. PORT R PDI RESET PRO PR1 PIN # 56 57 58 59 SYNC SYNC INTERRUPT Port R - Alternate functions PROGR PDI_DATA PDI_CLOCK XTAL2 XTAL1 XTAL 52 8068E–AVR–08/08 XMEGA A3 30. Peripheral Module Address Map The address maps show the base address for each peripheral and module in XMEGA A3. For complete register description and summary for each peripheral module, refer to the XMEGA A Manual. Base Address 0x0000 0x0010 0x0014 0x0018 0x001C 0x0030 0x0040 0x0048 0x0050 0x0060 0x0068 0x0070 0x0078 0x0080 0x0090 0x00A0 0x00B0 0x00C0 0x0100 0x0180 0x01C0 0x0200 0x0240 0x0320 0x0380 0x0390 0x0400 0x0480 0x04A0 0x0600 0x0620 0x0640 0x0660 0x0680 0x06A0 0x07E0 0x0800 0x0840 0x0880 0x0890 0x08A0 0x08B0 0x08C0 0x08F8 0x0900 0x0940 0x0990 0x09A0 0x09B0 0x09C0 0x0A00 0x0A40 0x0A80 0x0A90 0x0AA0 0x0AB0 0x0AC0 0x0B00 0x0B90 0x0BA0 Name GPIO VPORT0 VPORT1 VPORT2 VPORT3 CPU CLK SLEEP OSC DFLLRC32M DFLLRC2M PR RST WDT MCU PMIC PORTCFG AES DMA EVSYS NVM ADCA ADCB DACB ACA ACB RTC TWIC TWIE PORTA PORTB PORTC PORTD PORTE PORTF PORTR TCC0 TCC1 AWEXC HIRESC USARTC0 USARTC1 SPIC IRCOM TCD0 TCD1 HIRESD USARTD0 USARTD1 SPID TCE0 TCE1 AWEXE HIRESE USARTE0 USARTE1 SPIE TCF0 HIRESF USARTF0 Description General Purpose IO Registers Virtual Port 0 Virtual Port 1 Virtual Port 2 Virtual Port 2 CPU Clock Control Sleep Controller Oscillator Control DFLL for the 32 MHz Internal RC Oscillator DFLL for the 2 MHz RC Oscillator Power Reduction Reset Controller Watch-Dog Timer MCU Control Programmable MUltilevel Interrupt Controller Port Configuration AES Module DMA Controller Event System Non Volatile Memory (NVM) Controller Analog to Digital Converter on port A Analog to Digital Converter on port B Digital to Analog Converter on port B Analog Comparator pair on port A Analog Comparator pair on port B Real Time Counter Two Wire Interface on port C Two Wire Interfaceon port E Port A Port B Port C Port D Port E Port F Port R Timer/Counter 0 on port C Timer/Counter 1 on port C Advanced Waveform Extension on port C High Resolution Extension on port C USART 0 on port C USART 1 on port C Serial Peripheral Interface on port C Infrared Communication Module Timer/Counter 0 on port D Timer/Counter 1 on port D High Resolution Extension on port D USART 0 on port D USART 1 on port D Serial Peripheral Interface on port D Timer/Counter 0 on port E Timer/Counter 1 on port E Advanced Waveform Extensionon port E High Resolution Extension on port E USART 0 on port E USART 1 on oirt E Serial Peripheral Interface on port E Timer/Counter 0 on port F High Resolution Extension on port F USART 0 on port F 53 8068E–AVR–08/08 XMEGA A3 31. Interrupt Vector Summary. 31.1 USART Interrupt vectors USART Interrupt vectors Source RXC DRE TXC Interrupt Description USART Receive Complete Interrupt vector offset USART Data Register Empty Interrupt vector offset USART Transmit Complete Interrupt vector offset Table 31-1. Offset 0 2 4 31.2 Timer/Counter Interrupt vectors Timer/Counter Interrupt vectors Source OVF ERR CCA CCB CCC CCD (1) (1) Table 31-2. Offset 0 2 4 6 8 0x0A Note: Interrupt Description Timer/Counter Overflow/Underflow Interrupt vector offset Timer/Counter Error Interrupt vector offset Timer/Counter Compare or Capture Channel A Interrupt vector offset Timer/Counter Compare or Capture Channel B Interrupt vector offset Timer/Counter Compare or Capture Channel C Interrupt vector offset Timer/Counter Compare or Capture Channel D Interrupt vector offset 1. Only available on Timer/Counter with 4 Compare or Capture channels 16-bit. 31.3 SPI Interrupt vectors SPI Interrupt vectors Source SPI Interrupt Description SPI Interrupt vector offset Table 31-3. Offset 0 31.4 TWI Interrupt vectors TWI Interrupt vectors Source MASTER SLAVE Interrupt Description TWI Master Interrupt vector offset TWI Slave Interrupt vector offset Table 31-4. Offset 0 2 54 8068E–AVR–08/08 XMEGA A3 31.5 DMA Interrupt vectors DMA Interrupt vectors Source CH0 CH1 CH2 CH3 Interrupt Description DMA Controller Channel 0 Interrupt vector offset DMA Controller Channel 1 Interrupt vector offset DMA Controller Channel 2 Interrupt vector offset DMA Controller Channel 3 Interrupt vector offset Table 31-5. Offset 0 2 4 6 31.6 Crystal Oscillator Failure Interrupt vector Crystal Oscillator Failure Interrupt vector Source OSCF Interrupt Description Crystal Oscillator Failure Interrupt vector (NMI) offset Table 31-6. Offset 0 31.7 RTC Interrupt vectors RTC Interrupt vectors Source COMP PER Interrupt Description Real Time Counter Compare Match Interrupt vector offset Real Time Counter Period Interrupt vector offset Table 31-7. Offset 0 2 31.8 AES Interrupt vector AES Interrupt vector Source AES Interrupt Description AES Interrupt vector offset Table 31-8. Offset 0 31.9 NVM Interrupt vectors NVM Interrupt vectors Source SPM EE Interrupt Description Non-Volatile Memory SPM Interrupt level vector offset Non-Volatile Memory EEPROM Interrupt level vector offset Table 31-9. Offset 0 2 55 8068E–AVR–08/08 XMEGA A3 31.10 Analog Comparator Interrupt vectors Table 31-10. Analog Comparator Interrupt vectors Offset 0 2 4 Source COMP0 COMP1 WINDOW Interrupt Description Analog Comparator 0 Interrupt vector offset Analog Comparator 1 Interrupt vector offset Analog Comparator Window Interrupt vector offset 31.11 ADC Interrupt vectors Table 31-11. Analog to Digital Converter Interrupt vectors Offset 0 2 4 6 Source CH0 CH1 CH2 CH3 Interrupt Description Analog to Digital Converter Channel 0 Interrupt vector offset Analog to Digital Converter Channel 1 Interrupt vector offset Analog to Digital Converter Channel 2 Interrupt vector offset Analog to Digital Converter Channel 3 Interrupt vector offset 31.12 PORTS Interrupt vectors Table 31-12. Ports Interrupt vectors Offset 0 2 Source INT0 INT1 Interrupt Description Port Interrupt vector 0 offset Port Interrupt vector 1 offset 56 8068E–AVR–08/08 XMEGA A3 32. Instruction Set Summary Mnemonics Operands Description Arithmetic and Logic Instructions ADD ADC ADIW SUB SUBI SBC SBCI SBIW AND ANDI OR ORI EOR COM NEG SBR CBR INC DEC TST CLR SER MUL MULS MULSU FMUL FMULS FMULSU DES Rd, Rr Rd, Rr Rd, K Rd, Rr Rd, K Rd, Rr Rd, K Rd, K Rd, Rr Rd, K Rd, Rr Rd, K Rd, Rr Rd Rd Rd,K Rd,K Rd Rd Rd Rd Rd Rd,Rr Rd,Rr Rd,Rr Rd,Rr Rd,Rr Rd,Rr K Add without Carry Add with Carry Add Immediate to Word Subtract without Carry Subtract Immediate Subtract with Carry Subtract Immediate with Carry Subtract Immediate from Word Logical AND Logical AND with Immediate Logical OR Logical OR with Immediate Exclusive OR One’s Complement Two’s Complement Set Bit(s) in Register Clear Bit(s) in Register Increment Decrement Test for Zero or Minus Clear Register Set Register Multiply Unsigned Multiply Signed Multiply Signed with Unsigned Fractional Multiply Unsigned Fractional Multiply Signed Fractional Multiply Signed with Unsigned Data Encryption Rd Rd Rd Rd Rd Rd Rd Rd + 1:Rd Rd Rd Rd Rd Rd Rd Rd Rd Rd Rd Rd Rd Rd Rd R1:R0 R1:R0 R1:R0 R1:R0 R1:R0 R1:R0 if (H = 0) then R15:R0 else if (H = 1) then R15:R0 Branch Instructions RJMP IJMP EIJMP JMP RCALL ICALL EICALL k k k Relative Jump Indirect Jump to (Z) Extended Indirect Jump to (Z) Jump Relative Call Subroutine Indirect Call to (Z) Extended Indirect Call to (Z) PC PC(15:0) PC(21:16) PC(15:0) PC(21:16) PC PC PC(15:0) PC(21:16) PC(15:0) PC(21:16) ← ← ← ← ← ← ← ← ← ← ← PC + k + 1 Z, 0 Z, EIND k PC + k + 1 Z, 0 Z, EIND None None None None None None None 2 2 2 3 2 / 3(1) 2 / 3(1) 3(1) ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← ← Rd + Rr Rd + Rr + C Rd + 1:Rd + K Rd - Rr Rd - K Rd - Rr - C Rd - K - C Rd + 1:Rd - K Rd • Rr Rd • K Rd v Rr Rd v K Rd ⊕ Rr $FF - Rd $00 - Rd Rd v K Rd • ($FFh - K) Rd + 1 Rd - 1 Rd • Rd Rd ⊕ Rd $FF Rd x Rr (UU) Rd x Rr (SS) Rd x Rr (SU) Rd x Rr