U479B-MFPG3Y

Features • • • • • • • • • • 2-kV ESD Protection Two Comparators with Common Reference Tight Threshold Tolerance Threshold Matched to PTC Characteristic of Incandescent Lamps Temperature Compensated NPN Output Interference and Damage-protection According to VDE 0839 EMI Protection Reversal Polarity Protection Load-dump Protection Automotive Lamp-outage Monitor IC U479B 1. Description The monolithic integrated bipolar circuit, U479B, is designed as a monitor for lamp failure in automobiles. The comparator threshold is matched to the PTC characteristic of incandescent lamps. The threshold is tied to V4,6 = VS – VT where VT = 8 mV. If the voltage drop across the shunt resistor, Rsh, exceeds 8 mV, the output is turned off, otherwise, the output is turned on. Without supply voltage or open input pin 8, the output is turned off. A comparator input, which is not used, must be connected to pin 7. Figure 1-1. Schematic and Application Circuit VS 2 Rsh Z2 + 0.6 VS + 8 + 6 1 Lamps R1 3 & & VBatt 7 5 OUT1 4 Rsh OUT2 150 Ω Rev. 4775B–AUTO–09/05 2. Pin Configuration Figure 2-1. Pinning DIP8/SO8 1 2 3 4 8 INPUT VREF IN2 OUT1 GND VS OUT2 7 6 5 1N1 Table 2-1. Pin 1 2 3 4 5 6 7 8 Pin Description Symbol GND VS OUT2 IN1 OUT1 IN2 VREF INPUT Function Reference point, ground Supply voltage Output 2 Input 1 Output 1 Input 2 Reference voltage Input switch 2 U479B 4775B–AUTO–09/05 U479B 3. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Supply voltage Current consumption, t = 2 ms Output current Input voltage Reference point pin 7 Power dissipation Tamb = 95°C Tamb = 60°C Ambient temperature range Storage temperature range Junction temperature DIP8 SO8 DIP8 SO8 Pin 2, 7 1 3, 5 4, 6 Symbol VS I1 I3,5 -V4,6 Ptot Ptot Ptot Ptot Tamb Tstg Tj Value 16.5 1.5 20 6 Unit V A mA V 420 360 690 560 –40 to +95 –55 to +125 150 mW mW mW mW °C °C °C 4. Thermal Resistance Parameters Junction ambient DIP8 SO8 Symbol RthJA RthJA Value 110 160 Unit K/W K/W 3 4775B–AUTO–09/05 5. Electrical Characteristics VS = 9V to 15V, Tamb = –40 to +95°C, Figure 1-1 on page 1, unless otherwise specified. Parameters Supply voltage Internal Z-diode Z2 Current consumption Output saturation voltage VS = 12V VS = 9V, I3,5 = 10 mA Tamb = 25°C Reference point VPin 7 I3,5 = 3 mA VS = 12V VS = 15V V T(15 V) – V T(12 V) ∆ V = -------------------------------------------15 V – 12 V Switch identification Input 1/input 2 Input switch Switch-on, high to low Switch-off, low to high 8 4, 6 8 3, 5 Test Conditions Pin 2, 7 2 1 3, 5 Symbol VS VZ I1 Vsat Min. 9 20 4.5 6 0.5 Typ. Max. 15 Unit V V mA V Control signal threshold 4, 6 –VT –VT ∆V V8 II II td(on) td(off) 6.5 7.8 8 9.3 0.45 0.6 VS 100 5 6 30 9.5 10.8 mV mV mV/V V nA µA µs µs Voltage drift Threshold voltage Input currents Delay time Figure 5-1. Delay Times V4,6 12.00 11.95 V td(off) V0 12 6 V 0 10 20 30 40 50 td(on) 60 µs t 4 U479B 4775B–AUTO–09/05 U479B 6. Ordering Information Extended Type Number U479B-MY U479B-MFPY U479B-MFPG3Y Package DIP8 SO8 SO8 Remarks Pb-free Tubed, Pb-free Taped and reeled, Pb-free 7. Package Information P a c k a g e D IP 8 D im e n s io n s in m m 9 .8 9 .5 1 .6 4 1 .4 4 7 .7 7 7 .4 7 4 .8 m a x 6 .4 m a x 0 .5 m in 0 .5 8 0 .4 8 7 .6 2 8 5 2 .5 4 3 .3 0 .3 6 m a x 9 .8 8 .2 te c h n ic a l d ra w in g s a c c o rd in g to D IN s p e c ific a tio n s 1 4 5 4775B–AUTO–09/05 Package SO8 Dimensions in mm 5.00 4.85 1.4 0.4 1.27 3.81 8 5 0.25 0.10 5.2 4.8 3.7 0.2 3.8 6.15 5.85 technical drawings according to DIN specifications 1 4 8. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4775B-AUTO-09/05 History • Put datasheet in a new template • Pb-free logo on page 1 added • Ordering Information on page 5 changed 6 U479B 4775B–AUTO–09/05 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Literature Requests www.atmel.com/literature Disclaimer: T he information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. A tmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2005 . A ll rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® a nd others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4775B–AUTO–09/05